ZyXEL Communications P-660HNT1 User manual

www.zyxel.com
802.11n Wireless ADSL2+ 4-port
Gateway
Firmware v3.40
Edition 2, 8/2010
P-660HN-TxA
DEFAULT LOGIN DETAILS
IP Address: http://192.168.1.1
Password: 1234
Copyright 2010
ZyXEL Communications Corporation

2
Device Panels
POWER
LAN1-4
INTERNET
WPS/WLAN
DSL
WPS/WLAN
BUTTON
RESET
LAN PORT 1-4
ON/OFF
POWER
DSL PORT

P-660HN-TxA
3
Overview
The P-660HN-TxA is an ADSL router with a four-port built-in Ethernet
switch and IEEE 802.11n wireless capability. The P-660HN-TxA allows
wired and wireless clients to safely access the Internet.
Hardware Connections
This section shows you how to set up your P-660HN-TxA.
2
1
4
3

4
1. DSL: Use a telephone wire to connect your P-660HN-TxA’s DSL port
to a telephone jack (or to a splitter, if one is already installed).
2. LAN: Use an Ethernet cable to connect a computer to a LAN port for
initial configuration and/or Internet access.
3. POWER: Use the power adaptor provided with your P-660HN-TxA to
connect an appropriate power source to the POWER socket. Make
sure the power source is on.
4. Push the ON/OFF button to the ON position. Look at the lights on the
front panel.
• The POWER light blinks while your P-660HN-TxA starts up and
stays on once it is ready. The DSL light is on when the P-660HN-
TxA has a DSL connection, and the WLAN light is on when the
wireless LAN is ready. The INTERNET light is on when you are
able to access the Internet and blinks when the P-660HN-TxA is
sending or receiving data.
• Each LAN light stays on if the corresponding LAN port is properly
connected and blinks when there is traffic.
If any of these lights are not on, check your connections, and inspect
your cables for damage. If the lights are still off, contact your local
vendor.

P-660HN-TxA
5
Internet and Wireless Setup
1. In your browser, go to http://192.168.1.1.
2. Enter the default password 1234 and click Login.

6
3. Click Go to Wizard setup. Then, click Apply.
4. Click INTERNET/WIRELESS SETUP. Wait while your P-660HN-TxA
tries to detect your DSL connection.
5. Follow the directions in the wizard. Do not change default settings if
your ISP did not provide information.

P-660HN-TxA
7
Troubleshooting
1. If you cannot access the web configurator using Internet Explorer in
Windows XP or Windows Server 2003, make sure you allow pop-up
windows, JavaScripts and Java permissions or set the Internet
security level lower than High in Internet Explorer (in Internet
Explorer, click Tools > Internet Options > Security > Custom
Level...). See the appendix in the User’s Guide for more information.
2. If you cannot access the Internet when your computer is connected to
the LAN port, follow these steps.
a. Check the lights on the front panel. If they are different from what is
described on page 4, make sure the P-660HN-TxA is correctly
connected. If the lights are still different, turn off the device, wait a
few seconds, and turn it on again.
b. Follow the steps on page 7again. Make sure you enter the correct
information. For example, if your account has a user name and
password, make sure you type it correctly. In addition, if you are not
sure which encapsulation your ISP uses, contact your ISP.
c. If you are using a new Internet account, contact your ISP to make
sure it is active.
d. If you still have problems, see Troubleshooting in the User’s
Guide.
3. If you cannot access the Internet using the wireless network, follow
these steps.
a. On a computer in the wireless network, open your browser, and go
to http://192.168.1.1. If you see the login screen, follow
suggestions a- dabove. If you do not, go to the next step.

8
b. Make sure your P-660HN-TxA and your computer are using the
same wireless and wireless security settings.
Viewing Certification(s)
• Go to www.zyxel.com.
• Select your product from the drop-down list box on the ZyXEL home
page to go to that product's page.
• Select the certification you wish to view from this page.