ZyXEL Communications P-660HW-D Series User manual

P-660HW-D
ADSL2+ 4-port Gateway
Quick Start Guide
Version 3.40
1/2007
Edition 2

P-660HW-D Quick Start Guide
2
Overview
The P-660HW-D is an ADSL router with a four-port built-in Ethernet switch.
See your User’s Guide for background information on all features.
This Quick Start Guide shows you how to:
• Connect the hardware.
• Set up your Internet and wireless connection. The device should connect to the Internet automatically if it is pre-
configured. If you were given Internet connection information from your Internet Service Provider (ISP), you
may have to set up the connection manually (See section 3).
How to use the included CD
If you prefer to see a multi-media animation of how to make hardware connections, see the installation tutorial
on the included CD.
1On the included CD, click Multimedia Auto Provisioner > Installation Tutorial.
2At the end of the tutorial, click Configuration Genie to set up your P-660HW-D to connect to the Internet.

P-660HW-D Quick Start Guide
3
1 Hardware Connections
1DSL: Use the gray telephone wire to connect your P-660HW-D’s DSL port to a telephone jack (or to a
splitter, if one is already installed).
2ETHERNET: Use the yellow Ethernet cable to connect a computer to an ETHERNET port for initial
configuration and/or Internet access.
3POWER: Use the power adaptor provided with your P-660HW-D to connect an appropriate power source
to the POWER socket. Make sure the power source is on.
4Push in the POWER button.
5Look at the lights on the front panel.

P-660HW-D Quick Start Guide
4
•ThePOWER light blinks while your P-660HW-D starts up and stays on once it is ready.
•TheDSL light is on when the P-660HW-D has a DSL connection.
•TheINTERNET light is on when you are able to access the Internet and blinks when the P-660HW-D is send-
ing or receiving data.
• Each ETHERNET light stays on if the corresponding ETHERNET port is properly connected and blinks when
there is traffic.
If any of these lights are not on, check your connections, and inspect your cables for damage. If the lights are
still off, contact your local vendor.
2 Internet Connection Setup: Automatic
Use this section to have your P-660HW-D automatically detect and set up your Internet connection.
1Open your web browser. Your P-660HW-D tries to detect your Internet connection.
2Wait for the P-660HW-D to finish the connection test. This may take several minutes. If you do not see a
connection test screen similar to the following, go to step 5.
3If the connection test is successful, the following screen appears. Your Internet connection is ready for you
to use.

P-660HW-D Quick Start Guide
5
4If the connection test is not successful, you may see a screen similar to the following one. Follow the
instructions in the screen. If you still cannot access the Internet, take the steps in the following section. You
should have information provided by your Internet Service Provider.
5If you do not see the connection test screen, or if the connection test is not successful, check your
connections and restart the P-660HW-D. If you still cannot access the Internet, follow the steps in the
following section. You should have information provided by your Internet Service Provider.
3 Internet and Wireless Setup: Wizard
Use this section to set up your Internet connection if automatic Internet connection does not work (see section
2). You should have information from your Internet Service Provider (ISP).
1Open your browser and enter the P-660HW-D's IP address 192.168.1.1 (default) as the URL. If your
browser does not display a login screen, see Troubleshooting for details.
2Enter the admin password 1234 (default). Click Login.

P-660HW-D Quick Start Guide
6
3Type (and retype) a new password and click Apply.
Note: You have to use a new password other than the default password 1234, or you cannot apply it
successfully.
4The system asks you to enter your new password to log in again.
5Select Go to Wizard setup. Then, click Apply.

P-660HW-D Quick Start Guide
7
6Click INTERNET/WIRELESS SETUP. Wait while your P-660HW-D tries to detect your DSL connection.
7Click Next. Go to step 8to configure wireless settings.
If the connection test is not successful, you may see either a screen similar to one of the following. Either
click Restart the Internet/Wireless Setup Wizard if available to have the ZyXEL Device detect your
connection again or click Next to set up your Internet connection manually.

P-660HW-D Quick Start Guide
8
Follow up the instructions in the wizard. Enter your Internet connection information exactly as provided by your
ISP. If you do not see the following screen, go to section 4.
8Select Active and click Next to continue. Make sure Enable OTIST is not selected (recommended).
Note: ZyXEL's One-Touch Intelligent Security Technology (OTIST) feature allows you to automatically
configure the SSID and WPA-PSK on all OTIST-equipped wireless clients within range of the P-
660HW-D. For more information of OTIST, see OTIST on page 12.

P-660HW-D Quick Start Guide
9
9Configure your wireless settings in the screen. Click Next.
10 Follow the directions in the screen. The screen varies depending on the security you choose. Click Next to
continue.
11Click Apply to save your wireless LAN settings.

P-660HW-D Quick Start Guide
10
12Use the read-only summary table to check whether what you have configured is correct. Click Finish to
complete and save the wizard setup.
13The Internet connection is ready for you to use.
4 Internet Connection Setup: Manual
Use this section to set up your Internet connection manually if you do not see the ISP Parameters for Internet
Access screen when you run the wizard (see section 3).
1Follow steps 1to 3in section 3in order to log in to the web configurator.
2Select Go to Advanced setup. Then, click Apply.