ZyXEL Communications ZyWALL USG 100 Series User manual

www.zyxel.com
Unified Security Gateway
Firmware v2.11
Edition 1, 11/2008
DEFAULT LOGIN DETAILS
IP Address: https://192.168.1.1
Username: admin
Password: 1234
CONTENTS
ENGLISH 3
DEUTSCH 19
ESPAÑOL 37
FRANÇAIS 53
ITALIANO 69
РУССКИЙ 85
简体中文 101
繁體中文 115
QUICK START GUIDE
ZyWALL USG 100
ZyWALL USG 200
Copyright 2008 ZyXEL Communications Corporation
C

2
Front and Rear Panels
USG 100
USG 200
SYS CARD
PWR AUX
USB 1-2 P1 - P7
AUX CONSOLE EXTENSION
CARD SLOT
POWER
AUX CONSOLE EXTENSION
CARD SLOT
POWER
PWR AUX
SYS CARD USB 1-2 P1 - P7
RESET
RESET

ENGLISH
3
ENGLISH
Checking the Package Contents
Your package should include one of each of the following:
• ZyWALL
• Power cord
• Rack-mounting kit
• RJ-45 Ethernet cable
• RS-232 console Y-cable
• Printed Quick Start
Guide
• Compact
disk (CD)

4
Rack-mounted Installation
Mount the ZyWALL in a 19-inch rack or place it on a sturdy, flat surface.
Leave 10 cm of clearance at the sides and 20 cm in the rear.
1. Align one bracket with the holes on one side of the ZyWALL and
secure it with the included bracket screws. Similarly, attach the other
bracket.
2. After attaching both mounting brackets, position the ZyWALL in the
rack by lining up the holes in the brackets with the appropriate holes
on the rack. Secure the ZyWALL to the rack with the rack-mounting
screws.
.

ENGLISH
5
Connecting the Hardware
1. It is recommended that you configure the ZyWALL before using it to
protect your network. Use an Ethernet cable to connect a computer to
port P4.
2. Use another Ethernet cable(s) to connect port 1 and/or port 2to an
Ethernet jack with Internet access.
3. Use the included power adaptor to connect the power socket (on the
rear panel) to a power outlet.

6
4. Look at the front panel. The PWR light turns on. The SYS light blinks
during system testing and initialization and then stays on when the
system is ready.

ENGLISH
7
Web Login
1. Launch your web browser
and go to http://192.168.1.1
(the ZyWALL automatically
redirects you to https://
192.168.1.1).
2. Click Yes to proceed if
you get a security alert
or certificate screen.

8
3. Enter admin as
the user name
and 1234 as the
password. Click
Login.
4. It is strongly recommended
that you change the
password. Type and retype
a new password, and click
Apply.

ENGLISH
9
Installation Setup Wizard
Use an installation setup wizard to connect to the Internet and register
the ZyWALL and/or activate trial services, like IDP and content filter.
Use the installation wizard only for initial configuration starting
from the default configuration.
The Status screen opens. Click the Wizard icon in the upper right
corner.

10
Changes you make in the installation wizard may not be applied if you
have already changed the ZyWALL’s configuration.
• INSTALLATION
SETUP, ONE ISP
sets up a single
Internet
connection for
wan1.
• INSTALLATION SETUP, TWO ISP sets up Internet connections for
wan1 and wan2.
The wizard screens vary
depending on the
encapsulation type you use.
Refer to information
provided by your ISP and
the web help screens to
know what to enter in each
field. You can leave fields
blank if you don’t have that
information.