ZyXEL Communications PRESTIGE 660RU Series User manual

Prestige 660RU Series
ADSL2+ Ethernet/USB Gateway
Quick Start Guide
Version 3.40
01/2005

Prestige 660RU Series Quick Start Guide
2
Introducing the Prestige
The Prestige 660RU ADSL2+ USB/Ethernet Gateway is the ideal all-in-one device for
small networks connecting to the Internet via ADSL. Provided with both USB and
Ethernet ports, computers can share local resources (such as printers and files) and
access to the Internet - simultaneously. See your User’s Guide for more details on all
Prestige features.
You should have an Internet account already set up and have been given most of the
following information.
INTERNET ACCOUNT INFORMATION
Virtual Path Identifier (VPI): ____________
Virtual Channel Identifier (VCI): ____________
Multiplexing (VC-based or LLC-based): VC LLC
Your device’s WAN IP Address (if given): __________________
DNS Server IP Address (if given): Primary: ___________________
Secondary: _________________
Encapsulation or Protocol (choose one below)
RFC 1483
ENET ENCAP Ethernet Encapsulation Gateway IP Address: ________________
PPPoA User Name: ____________ Password: ____________
PPPoE (PPPoE) Service Name: ____________
User Name: ____________ Password: ____________
Overview
This guide shows you how to connect and access the Internet through your Prestige via
the Ethernet or the USB port. You should have an Internet account already set up.
1. Make the hardware connections.
2. Check front panel LEDs for proper hardware operation.
3. Access the Internet via the Ethernet port or the USB port after USB driver
installation.

Prestige 660RU Series Quick Start Guide
3
Hardware Connections
1. Connect the Prestige to a telephone jack using a telephone wire.
2. Use an Ethernet cable to connect a computer to the LAN 10/100M port for
initial configuration and/or Internet access.
3. If you have a USB-enabled computer that does not have a network
interface card for attaching to your Ethernet network, connect the computer
to the USB port with a USB cable. Refer to the Installing the USB Driver
section.
4. Connect to a power source using the included power adaptor.
5. After you’ve made the connections, connect the power adaptor to a power
supply and push in the power button to turn on the Prestige. Look at the
front panel LEDs.
Check Front Panel LEDs
When the Prestige is turned on, the PWR/SYS LED and USB LEDs blink while
performing system testing. The PWR/SYS LED then turns steady on if the testing is

Prestige 660RU Series Quick Start Guide
4
successful. The appropriate LAN and/or USB LEDs turn on if they are properly
connected. See your User’s Guide for detailed LED descriptions.
Zero Configuration Internet Access
Once you connect and turn on the Prestige, it automatically detects the Internet
connection settings from the ISP and makes the necessary configuration changes.
1. Wait until the DSL LED turns steady on. Launch your web browser and navigate to
a web site (for example, www.zyxel.com). The Prestige automatically detects and
configures your Internet connection. This may take about two minutes.
2. If you have a PPPoE or PPPoA connection, a screen displays prompting you to
enter your Internet account information. Enter the username, password and/or
service name exactly as provided by your ISP. Click Apply.
3. You should be able to access the Internet. Otherwise, follow the on-screen
instructions to solve the problem(s). Refer to the rest of this guide or the User’s
Guide to manually configure your Prestige for an Internet connection and other
advanced settings.

Prestige 660RU Series Quick Start Guide
5
If an Internet access parameter is changed, either restart the
device to have the Prestige automatically reconfigure your
Internet connection or change it manually in the Wizard screens
of the web configurator (see your User’s Guide for details).
Prestige Factory Defaults
This Quick Start Guide provides a basic configuration that should be compatible with
your home or small office network setup. Refer to the User’s Guide for additional
configuration instructions.
PRESTIGE FACTORY DEFAULTS
USB/LAN IP Address 192.168.1.1 Subnet Mask 255.255.255.0
Default Password 1234 DHCP IP Pool 192.168.1.33 – 192.168.1.64
Installing the USB Driver
If you want to connect to the Internet through the Prestige’s USB port, follow the steps
for your operating system to install the USB driver.
Windows
System Requirements
• Windows 98 SE (Second Edition), Windows Me (Millennium Edition),
Windows 2000 or Windows XP
• An available USB port
Install the USB driver before you connect the Prestige to the
USB port.
Screen shots for Windows XP are shown in the following procedure unless otherwise
specified.
1. Save your work and close all other Windows applications.
2. Insert the included CD. The CD automatically runs and the main screen displays.
3. Double-click Install Driver on the main screen.

Prestige 660RU Series Quick Start Guide
6
4. A Welcome screen
displays, click Next.
5. Click Yes to agree to
the license
agreement.

Prestige 660RU Series Quick Start Guide
7
6. When a Start
Copying Files
screen displays, click
Next to continue.
7. Windows 98 SE/Me:
Select Yes, I want to
restart my
computer now. and
click OK.

Prestige 660RU Series Quick Start Guide
8
Windows 2000/XP:
Connect the Prestige
to the computer’s
USB port when
prompted. A window
displays briefly,
indicating that the
system has found
new hardware.
8. Windows XP: If a
warning window
displays, click
Continue Anyway.

Prestige 660RU Series Quick Start Guide
9
9. Click Finish to
complete the
installation.
Restart the computer
if prompted.
10. Windows 98 SE/Me: After the computer finishes restart, connect the square end
of the USB cable to the back of your Prestige and connect the rectangular end of
the USB 6cable to the back of your computer. A window displays briefly,
indicating that the system has found new hardware.
11. Windows 2000/XP: The login screen of the Prestige web configurator appears
automatically. Click Login to configure other features. Otherwise, close the
screen or just navigate to another web site.
Verifying Your USB Installation
The screen for Windows XP is shown here.
Check the status of the Prestige in the
Device Manager window. Click Start,
Settings, Control Panel, System,
Hardware and then click Device Manager.
(Steps may vary depending on the version of
Windows).
Verify the status of the Prestige under
Network Adapter. Check that there is no
question mark on the device icon for the
Prestige.

Prestige 660RU Series Quick Start Guide
10
Mac
System Requirements
• Macintosh operating system versions 10.1 and later
• An available USB port
Install the USB driver before you connect the Prestige to the
USB port.
Screen shots for Macintosh 10.3 are shown in the following procedure unless otherwise
specified. The screens on your computer may differ slightly from the screens shown
here depending on the version of your operating system.
1. Close all programs and applications
2. Insert the included CD into the CD-ROM drive. An icon for the CD appears.
3. Double-click the CD’s icon.
4. Copy the driver ZyXEL(TMX.1.0.C0).ZIP to the desktop and extract this .ZIP file.
Double-click ZyXEL(TMX.1.0.C0).
5. Double-click
P660RU-Tx.dmg.
The file P660RU-
Tx.pkg will be
created.

Prestige 660RU Series Quick Start Guide
11
6. Double-click
P660RU-Tx.pkg to
install the driver.
7. A welcome screen
appears. Click
Continue.
8. You will then see the
Select a Destination
screen, select a
destination (this must
be on an actual
physical hard drive
on the Macintosh, not
a virtual drive) and
click Continue.

Prestige 660RU Series Quick Start Guide
12
9. Click Upgrade.
10. You then see a
screen telling you
that you must restart
the computer after
the installation
completes. Click
Continue
Installation. The
driver will
automatically install.
11. Click Restart to
reboot your computer
and complete the
driver installation.

Prestige 660RU Series Quick Start Guide
13
Troubleshooting
PROBLEM CORRECTIVE ACTION
The PWR/SYS
LED is off.
Make sure the Prestige is connected to the correct power adaptor,
the power adaptor is connected to an adequate power supply and
the Prestige power switch is turned on.
Turn the Prestige off and on. If the error persists, you may have a
hardware problem. In this case, you should contact your local
vendor.
The 10/100M
LED won’t turn
on.
Check the cable connection to the Prestige LAN 10/100M port.
Make sure your computer network card is working properly.
The DSL LED is
off.
Check the connection between the Prestige DSL port and the wall
jack.
I cannot ping
any computer on
the LAN.
If all of the LAN LEDs are off, check the cables between the
Prestige and your computer or hub.
Check the TCP/IP configuration on your computer. Make sure that
the IP address and the subnet mask of the Prestige and the
computer are in the same range.
Refer to the appendix in your User’s Guide for more information
about setting up the IP address on your computer.
USB driver
installation
crashes my
computer.
You may have a sniffer program installed. Remove any sniffer
applications on the computer and reboot the computer.
Reinstall the USB driver.

Prestige 660RU Series Quick Start Guide
14
PROBLEM CORRECTIVE ACTION
The USB LED is
off or Windows
does not auto-
detect the USB
connection to
the Prestige.
Make sure the Prestige is turned on and connected to the USB port
on the computer.
Perform a hardware scan by clicking Start, Settings, Control
Panel and double-clicking Add/Remove Hardware. (Steps may
vary depending on the version of Windows).
Follow the on-screen instructions to search for the Prestige and
install the driver.
Check for possible hardware conflicts. In Windows, click Start,
Settings, Control Panel, System, Hardware and then click
Device Manager. Verify the status of the Prestige under Network
Adapter. (Steps may vary depending on the version of Windows).
Remove the USB driver and install it on the computer again.
Connect the Prestige to another computer. If the error persists, you
may have a hardware problem. In this case, you should contact
your local vendor.
The PPP LED is
off.
Make sure the Prestige is turned on and you have a PPPoE or
PPPoA connection.
Make sure you entered your username, password and/or service
name correctly. A username may be case-sensitive.
Check the schedule rules. Refer to the Call Scheduling chapter
(SMT) in the User’s Guide.
If you use PPPoA or PPPoE encapsulation, check the idle time-out
setting. Refer to the WAN chapter (web configurator) or the
Remote Node Configuration chapter (SMT) in the User’s Guide.
Contact your ISP.
Certifications
1. Go to www.zyxel.com.
2. Select your product from the drop-down list box on the ZyXEL home page to go to
that product's page.
3. Select the certification you wish to view from this page.