ZyXEL Communications SBG3600-N SERIES User manual

SBG3600-N Series
LTE Multi-WAN Small Business Gateway
Version 1.00
Edition 1, 4/2015
Default Login Details
LAN IP Address http://192.168.1.1
User Name admin
Password 1234
Copyright © 2015 ZyXEL Communications Corporation
Quick Start Guide

2
Device Panels
RESET DSL
GBE USB
SFP
LEDS
LAN 1-4
ON/OFF
POWER
WLAN
CONSOLE
SBG3600-N
SIM CARD

3
RESET DSL
GBE USB
SFP
LEDS
LAN 1-4
ON/OFF
POWER
WLAN
CONSOLE
SBG3600-NB
SIM CARD

4
Requirements
Make sure you have the following before you start:
• INTERNET ACCESS: You need an Internet account with an ISP (Internet
Service Provider) and information such as your user name, password, and
so on.
• WEB BROWSER: Internet Explorer 8.0 and later versions, with JavaScript
enabled, or Mozilla Firefox 3 and later versions, Chrome, or Safari 2.0 and
later versions. The browser will be used to access the Internet and/or
access the Web Configurator.
Hardware Setup
1. Attach the wireless LAN antennas to the rear panel and point them up.
2. Attach the LTE antennas to the front panel and point them up.
2
1

5
3. Insert the LTE SIM card.
Insert the SIM card before you turn on the Device.
To connect the SBG3600-N:
3e
5
4a
6
7
4b
4c

6
To connect the SBG3600-NB:
4. Do one or more of the following to connect to the Internet.
a. DSL: Use a telephone cable to connect your Device’s DSL port to a
telephone jack (or the DSL or modem jack on a splitter if you have one).
If your ISP supports DSL bonding, you can connect DSL1 and DSL2 to two
separate telephone jacks and enable the bonding feature for increased
throughput at longer distances. See the User’s Guide for how to enable
bonding in the Web Configurator. 1
1. Applies to the SBG3600-N000.
5
4a
6
7
4b
4c

7
b. SFP: If fiber access is available, insert a fiber optic SFP module and
connect the fiber optic cable for Internet access. (See Transceiver
Installation and Removal on page 8for more information on SFP module.)
c. GbE: If you already have a broadband router or modem, use an Ethernet
cable to connect the GbE port to it for Internet access.
Your Device does not use Fiber (SFP) and broadband (GbE)
connections at the same time.
5. ETHERNET LAN: Use an Ethernet cable to connect a computer to an
Ethernet port for initial configuration and/or Internet access.
6. USB: Do one of the following USB connections:
a. Connect a USB (version 2.0 or lower) memory stick or a USB hard drive
for file sharing. The Device automatically detects the USB device.
b. Connect a 3G adapter to access the Internet wirelessly via a 3G network.
7. 12V DC: Use the provided power adaptor to connect the 12V DC socket on
the Device’s rear panel to an appropriate power source. Push the Device’s
ON/OFF button to the ON position. Make sure the power at the outlet is on.
Look at the lights on the front panel.
• The PWR light blinks while your Device starts up and then stays on once it
is ready.
• The DSL light is green when your Device has an ADSL connection. It is
orange when you have a VDSL connection. The DSL2 light comes on
when using DSL bonding1.
• The INET light turns on when the gateway is able to access the Internet.
• The USB light turns on when your Device detects a connected USB device
and blinks when there is traffic.
• The SFP light turns on after your Device has a fiber connection and blinks
when there is traffic.
1. Applies to the SBG3600-N000.

8
• The WLAN light flashes green when WLAN is activated. It stays on green
when the wireless LAN is ready and blinks when there is traffic.
• The LTE Signal light bars indicate the LTE signal quality. The more bars
turn on, the higher the signal quality.
• The LTE light flashes green while connecting to the LTE network. It stays
on green when the LTE connection is ready.
• An ETHERNET LAN port’s green light turns on if the port has a 1G LAN
connection. Its yellow light turns on for a 10/100M LAN connection. Either
light blinks for LAN traffic.
• The GbE port’s green light turns on if the port has a 1G WAN connection.
Its yellow light turns on for a 10/100M WAN connection. Either light blinks
for WAN traffic.
If the lights do not come on, check your connections and inspect your cables for
damage. If the lights are still off, contact technical support.
Transceiver Installation and Removal
To install a mini-GBIC transceiver (SFP module):
1. Insert the transceiver into the SFP slot.
2. Press the transceiver firmly until it clicks into place and close the
transceiver’s latch.
3. Connect the fiber optic cables to the transceiver.
To remove a mini-GBIC transceiver (SFP module).
1. Remove the fiber optic cables from the transceiver.
2. Open the transceiver’s latch.
2 31

9
3. Pull the transceiver out of the SFP slot.
Set Up a Wireless Network
Wireless LAN is enabled by default. Use the settings on the Device bottom
panel to configure wireless devices that you want to connect.
Wireless Settings Example
The default wireless settings vary by SBG3600-N Series Device. Use the
information on the bottom panel of your Device.
The Web Configurator
Use the Web Configurator web browser tool to configure the Device. Your
computer and the Device need to be in the same IP address range to use it.
1. Open your browser and enter http://192.168.1.1 (the Device’s default IP
address) as the address.
11 23
SSID: ZyXEL0A561
WPA2-PSK: FB373BD35636BC45