ZyXEL Communications LTE7461-M602 User manual

LTE7461-M602
4G LTE-A Outdoor Router
Copyright © 2019 Zyxel Communications Corp. All Rights Reserved.
See the User's Guide at www.zyxel.com for more information,
including customer support and safety warnings.
Quick Start Guide
1/4
US Importer
Zyxel Communications, Inc
1130 North Miller Street Anaheim, CA 92806-2001
http://www.us.zyxel.com
1 2
RESET SIM
L A N (P o E )
RESET SIM
L A N (P o E )
Make sure the LTE7461 is turned off. There should be no Ethernet cable connected providing
power using PoE. Unscrew the SIM card slot cover and remove it.
1Insert your SIM card provided by an LTE ISP (Internet Service Provider). 2
Step 1 SIM Card Installation
1 2 3 4
Follow steps 1 to 4 in the drawing to connect an 8-pin Cat 5e Ethernet cable to the LTE7461's LAN port.
1-4
Step 2 Cable Connections
Cat 5e (not supplied)
Power Injector
Power Outlet
Pole Mounting
Cat 5e (not supplied)
Power Injector
Power Outlet
Wall Mounting
Location Examples
Gateway
LaptopSmartphone PC
Place the LTE7461 in an open area free
of obstacles, and adjust the angle to
point it towards the base station to
have the strongest possible LTE signal.
Package Contents
LTE7461-M602 Gigabit
PoE Injector
GbE
Cable
Cable
Gland
Grounding
Wire
Power
Cord
Quick Start
Guide
Safety
Warnings
Hex NutsM6 Spring
Washers
Tapping Screw
M4x25 mm
Nylon Wall
Plugs
M6 Hex
Bolts x90L
x4x4 x4 x4x4
M6 Hex
Bolts x12L
Flat Brackets
x2
M Bracket Pre-assembled Kit
x4x4
M6 Washers
Mounting Kit

2/4
PoE injector
Power outlet
OUT IN
12
34
Step 3 Cable Connections
Connect the other end of the Ethernet cable to the provided PoE injector's OUT port.
Connect the IN port of the injector to a computer with an Ethernet cable for initial
configuration.
1
2
Connect the power plug on the PoE injector to a power outlet.
Check the LED next to the SIM card slot.
3
4
RESET SIM
L A N (P o E )
Red
Green Blinking - Connecting to the Internet
Steady - Connected to the Internet
Blinking - Booting
Steady - Error
Step 4 Connecting WiFi to Your LTE7461 for Easy Setup
OUT IN
User Name
Password
Login
xxxxxxxxxx
admin
Desktop Version
https://192.168.1.1
2
RESET SIM
1
Amber Blinking - WiFi is on
3
Check if WiFi is on - the Amber LED is blinking. If not, press the WiFi button to enable WiFi.
Remove the label from the back of he LTE7461 and put it on the injector. Connect to the LTE7461
WiFi network using the WIFI SSID and WIFI Key on the injector label, or on your smartphone
simply scan the QR code to connect.
1
2
You can download the LTE Ally app or use the web configurator (see next) to manage the
LTE7461.
Screw the SIM card slot cover back into place.
3
Scan the QR code on the device label to see the
SSID and WiFi Key on your smartphone.
Login a ddress : 192.168.1.1
User Name : admin
Login Password : XXXXXXXXXX
WiFi SSID : Zyxel_xxxx
WiFi Key : XXXXXXXXXX
PoE injector
4
4
RESET SIM
L A N (P o E )
LTE Ally
https://192.168.1.1
User Name: admin
Login Password: XXXXXXXXXX
LTE7461-M602
User Name
Password
Login
XXXXXXXXXX
admin
https://192.168.1.1
Open a web browser and go to https://192.168.1.1.
Enter the default username (admin) and password (see label), and then click Login.
See the User’s Guide at www.zyxel.com for more information.
Configuring Your LTE7461 (Optional)

3/4
A
x4
Unit: mm
25.4
8.0
1
95mm
95mm
2
Four Nylon Wall Plugs
Wall Mounting (Optional)
Use the four corner holes of the M bracket to mark holes on a wall. Drill four holes in a wall.
1 2 Insert the screw anchors and screws into the holes.
BTapping Screw M4x25 mm
Unit: mm
x4
25.4
4.0
2.38
9
Four M6 Washers
x4
x4
Four M6 Spring Washers
Four M6 Hex Bolts x12 L
One M Bracket
x4
x1
C
D
E
F
B
D
3
4
C
E
F
Secure the M bracket to the wall.
3 4 Secure the LTE7461 to the M bracket.
BFour M6 Washers
x4
A
x4
Four M6 Spring Washers
C
x4
Four Hex Nuts
A
B
C
Step 5 Pole / Wall Mounting: Connect Pre-assembled Bracket
Make sure the LTE7461 is turned off. Disconnect the PoE injector from the power outlet.
Use A, B and C to attach the bracket to the LTE7461.
Use the wrench to tighten the nuts in the final step.

4/4
Pole Mounting (Optional)
x2
Four M6 Washers
x4
x4
Four M6 Spring Washers
One M Bracket
C
D
E
Two Flat Brackets
F
BFour M6 Hex Bolts x12 L
AFour M6 Hex Bolts x90L
x4
x4
x1
A
F
F
C
1
2
B
D
E
Use A, F and C to attach the brackets to the pole.
1 2 Use B, D and E to attach the LTE7461 with the port facing down to C on the pole. Do not tighten
the bolts too much.
Step 6 Pole / Wall Mounting Angle Adjustment
-40°
horizontal
+40°
+0° horizontal
+30°
vertical
-30°
vertical
Turn the LTE7461 on. Connect the PoE injector to a power outlet.
Use the LTE Ally app to find the optimal LTE signal strength and manage your LTE7461.
Note: After configuring the LTE7461, turn WiFi off.
Step 7 Grounding
Use the M4 screw to secure the ground cable to the ground hole on the LTE7461’s rear panel.
Attach the other end of the cable to the ground, either to the same ground electrode as the pole you installed the device
on or to the main grounding electrode of the building.
Follow your country’s regulations and safety instructions to electrically ground the device properly.
Humid, dusty and extreme environment in which place the product and obstructing the device
ventilation slots are prohibited, any kind of conditions above may harm your device.
There is a remote risk of electric shock from lightning. Do not install, use, or service this device during
a thunderstorm.
Connect only suitable accessories to the device; make sure to connect the cables to the correct
ports.
Do not open the device, opening or removing covers can expose you to dangerous high voltage
points or other risks. Please contact your vendor for further information.
Place connecting cables carefully so that no one will step on them or stumble over them and
disconnect all cables from this device before servicing or disassembling.
Please use the provided or designated connection cables/power cables/ Power over Ethernet (PoE)
Injector connect it to the right supply voltage (for example, 110V AC in North America or 230V AC in
Europe), If the power cord or PoE is damaged, it might cause electrocution. remove it from the device
and the power source , repairing the power adapter or cord is prohibited , Contact your local vendor
to order a new one.
Please refer to the device back label, datasheet or box specifications catalog information for rated
power of device and operating temperature.
The socket-outlet shall be installed near the device, and shall be easily accessible because it serves
as the main disconnecting device.
Safety Warnings
Disposal and Recycling Information
The symbol below means that according to local regulations your product and/or its battery
shall be disposed of separately from domestic waste. If this product is end of life, take it to a
recycling station designated by local authorities. At the time of disposal, the separate
collection of your product and/or its battery will help save natural resources and ensure that
the environment is sustainable development.