ZyXEL Communications P-660R-T3 V2 Instruction Manual

ZyXEL Confidential
ZyXEL
Firmware Release Note
P-660R-T3 v2
Standard Version
Release 3.40(APT.1)C0
Date: Feb 10, 2007
Author: Jeff Sun
1/16

ZyXEL Confidential
ZyXEL P-660R-T3 v2 Standard Version
Release 3.40(APT.1)C0
Release Note
Date: Feb 10,2007
Supported Platforms:
ZyXEL P-660R-T3 v2
Versions:
ZyNOS Version : V3.40(APT.1) | 2/10/2007 09:21:21
Bootbase Version : V1.04 | 7/17/2006 09:52:52
Notes:
P-660R-T3 v2/T3 v2/T7 v2 is next generation of ZyXEL P660R series with higher speed
of ADSL2, ADSL2+ technology, speed up to 12Mbps (ADSL2) and 24 Mbps (ADSL2+).
With Ethernet, P-660R-T3 v2/T3 v2/T7 v2 offers the flexible way to access the Internet.
Features:
Modification in V3.40(APT.1) | 02/10/2007
1. change to FCS version
Modification in V3.40(APT.1)b1 | 02/06/2007
2. Create this project with new modem code, from 3.5.18.8 for Annex A to 3.5.29.2 for
Annex B.
Modification in V3.40(APT.0)b4 | 11/23/2006
1[BUG FIX]
SPRID:061114828
ProblemCategory:newfoundcommonissueinRxseries
ProblemSymptom:WhenLANPCusesdifferentIP(IPmustbeassigned
automatically)toenterGUI＞LAN＞ClientList,DUTwillcrash.
ProblemCondition:Step1:Restoredefaultsetting,LANPCcangetIP(for
example:192.168.1.33).
Step2:LANPCconfigureastaticIP(forexample:192.168.1.37),thenPCgetIP
192.168.1.37.
Step3:CancelstaticIPinLANPC,itwillgetIP192.168.1.37automatically.
Step4:LoginGUI＞AdvancedSetup＞LAN＞ClientList,DUTwillcrash.
2[BUG FIX]
SPRID:061114823
2/16

ZyXEL Confidential
ProblemCategory:commonissue
ProblemSymptom:ActiveWindowsNetworking(NetBIOSoverTCP/IP)inGUI/
advanced/LAN/IPPage,itcan＇tsave
ProblemCondition:step1.loginadvanced,innetwork‐＞LAN‐＞IPpage,click
“advancedsetup ＂button,inthefollowingpage,activeWindows
Networking(NetBIOSoverTCP/IP),allowbetweenLANtoWAN,thenclick
“apply＂.
step2.gotothepageagain,thesetcan ＇tsave,theWindows
Networking(NetBIOSoverTCP/IP)isstillinactive.
3[BUG FIX]
SPRID:061114821
ProblemCategory:NewDefect
ProblemSymptom:thereisredundantmessageinGUI.
ProblemCondition:InGUI＞status,thereisredundantmessageaboutSecurity.

Modification in V3.40(APT.0)b3 | 11/07/2006
1[BUGFIX]
SPRID:061031176
ProblemCategory:BATdefect
ProblemSymptom:Remotemanagementcannotwork
ProblemCondition:wanpccannotaccessdevicealthoughremotemanagement
allowedwanaccessdevice
2[BUGFIX]
SPRID:061031167
ProblemCategory:NewDefect
ProblemSymptom:ATMQoSTest‐ATMQoSprioritytestfail
ProblemCondition:useAX4000testQoSpriority,thepriorityofmoreremote
nodesisnotcorrect.
3[BUGFIX]
SPRID:061031172
ProblemCategory:NewDefect
ProblemSymptom:useftpcannotuploadFWfrom(APT.0)b1to(APT.0)b2
ProblemCondition:useftpcannotuploadFWfrom(APT.0)b1to(APT.0)b2
4[BUGFIX]
SPRID: 061031174
ProblemCategory: New Defect
Problem Symptom: GUI can not backup romfile
Problem Condition: GUI can not backup romfile,the backup romfile can not
download from device.
5[BUG FIX]
SPRID: 061031177
3/16

ZyXEL Confidential
ProblemCategory: New Defect
Problem Symptom: There is not user mode
Problem Condition: This FW can not find user mode,use password ”user” also
can not login user mode
6[BUG FIX]
SPRID: 061031179
ProblemCategory: New Defect
Problem Symptom: Wizard can not work correctly
Problem Condition: 1.There is not login page to login Wizard page and you must
first login in Admin mode then enter Wizard mode. 2.You must configure to
RFC1483 mode then Wizard can work correctly,else it can not work.
Modification in V3.40(APT.0)b2 | 10/24/2006
1. create this project with new gui
Modification in V3.40(APT.0)b1 | 08/16/2006
2. Create this project.
Known Issues:
1. If UPNP is disabled than MSN messenger whiteboard doesn't work behind NAT.
2. The TR-067 Loop test failure.
3. If there are two or more PVCs with CBR or VBR QOS type and the total PCR
requirement exceed the line rate then the bandwidth distribution between those PVCs is
unpredictable.
4. Setup two PVCs with 1483 bridge, each PVC with 500Kbps upstream and 10Mbps
downstream traffic. If packet size is 1500 The CPU loading is 88%. The CPU loading is
100% if packet size is 1024.
5. The VBR property of TrendChip is different form the others.
6. The value of MBS can’t be too large. Ex 10000.
7. F/W upgrade in eWC can not work with IE 5.0.3315.
8. MAC OS can’t login the WEBGUI through IE 5.2.
9. When we do the ETSI-101388 test with ALC1224-73, the downstream will have CRC
error and ADSL will retrain.
10. Use ax/4000 test VBR have problem.
11. Use ax/4000 test priority have problem in especially setting.
12. Any IP works fine at the first time, but after power on and off, it won’t work until 10
minutes later.
Modifications:
Modification in V3.40(APT.1)b1 | 02/06/2007
1. This version is based on P-660R-T1 v2(AGJ.3)C0
Modification in V3.40(APT.0)b3 | 11/07/2006
1 remove SPTGEN
2 add dynamic button in more connections
4/16

ZyXEL Confidential
Modification in V3.40(APT.0)b2 | 10/24/2006
1. This version is based on trunk Revision 1.281
Modification in V3.40(APT.0)b1 | 08/16/2006
1. This version is based on P-660R-T1 v2(AGJ.1)C0
2. Boot base CL= 3, set to E8
3. Default ROM File Value Setting
1 system version
P-660R-T3_v2> sys version
ZyNOS version: V3.40(APT.1) | 2/10/2007
romRasSize: 1112492
system up time: 0:00:11 (4a5 ticks)
bootbase version: V1.04 | 7/17/2006
ZyNOS CODE: P-660R-T3 v2 AT Feb 06 2007 17:03:55
2 modem code version
P-660R-T3_v2> wan adsl fwversion
DMT FwVer: 3.5.29.2_B_TC3085 HwVer: T14F7_1.0
3 Lan status
P-660R-T3> lan index 1
enif0 is selected
P-660R-T3> lan dis
Active: Yes
Interface: enif0
IP Address: 192.168.1.1
Subnet Mask: 255.255.255.0
RIP Direction: Both
RIP Version: RIP-2B
Multicast: IGMP-v2
Protocol Filter Set:
Incoming: 0 0 0 0
Outgoing: 0 0 0 0
Device Filter Set:
Incoming: 0 0 0 0
Outgoing: 0 0 0 0
4 Dhcp Status
P-660R-T3_v2> ip dhcp enif0 st
DHCP on iface enif0 is server
Start assigned IP address: 192.168.1.33/24
Number of IP addresses reserved: 32
Hostname prefix: dhcppc
DNS server: 0.0.0.0 0.0.0.0
WINS server: 0.0.0.0 0.0.0.0
Domain Name :
5/16

ZyXEL Confidential
Default gateway: 192.168.1.1
5 Wan status
P-660R-T3_v2> wan node index 1
P-660R-T3_v2> wan node disp
WAN node index = 1
Active = yes
Route IP = on
Bridge = off
Name = MyISP
Encapsulcation <2:PPPoE|3:RFC1483|4:PPPoA|5:Enet Encap> = 5
Mux <1:LLC|2:VC> = 1
VPI/VCI = 8 / 35
PPPoE service name =
PPP username = user
PPP password = 1234
PPP authentication <1:PAP|2:CHAP|3:BOTH> = 3
SUA/NAT is enabled, NAT lookupset = 255
Dynamic IP address
WAN IP address = 0.0.0.0
Remote IP address = 0.0.0.0
Remote IP subnet mask = 0.0.0.0
Idle timeout = 0
Call scheduling set = 0 0 0 0
Nailed-up connection = off
QOS Type <2:CBR|3:UBR|4:VBR_nRT|5:VBR_RT> = 3
QOS PCR/SCR/MBS = 0, 0, 0
RIP direction <0:none|1:both|2:in|3:out>= 0
RIP version <0:RIP-1|1:RIP-2B|2:RIP-2M> = 0
Multicast <0:IGMP-v2|1:IGMP-v1|2:none> = 2
Incoming protocol filter set = 0 0 0 0
Incoming device filter set = 0 0 0 0
Outgoing protocol filter set = 0 0 0 0
Outgoing device filter set = 0 0 0 0
Call protocol filter set = 0 0 0 0
Call device filter set = 0 0 0 0
6 Vc-autohunt table
P-660R-T3_v2> wan atm vc disp
(1) Configure Buffer
(2) RemoteNode (Read Only)
RN VPI VCI | RN VPI VCI | RN VPI VCI | RN VPI VCI |
---------------------------------------------------------------
1 8 35 | 2 0 0 | 3 0 0 | 4 0 0 |
5 0 0 | 6 0 0 | 7 0 0 | 8 0 0 |
(3) VC Hunt Table: (User setting)
Flags: Active(1)
RN VPI VCI serv| RN VPI VCI serv| RN VPI VCI serv| RN VPI VCI serv
6/16

ZyXEL Confidential
---------------------------------------------------------------
1 0 33 3fH| 1 0 35 3fH| 1 1 35 3fH| 1 8 32 3fH|
1 0 101 3fH| 1 0 50 3fH| 1 0 32 3fH| 1 14 24 3fH|
0 0 0 0H| 0 0 0 0H|
(4) WebRedirect: Enable
7 Autoexec.net display
P-660R-T3_v2> sys view autoexec.net
sys errctl 0
sys trcl level 5
sys trcl type 1180
sys trcp cr 64 96
sys trcl sw off
sys trcp sw off
ip tcp mss 512
ip tcp limit 2
ip tcp irtt 65000
ip tcp window 2
ip tcp ceiling 6000
ip rip activate
ip rip merge on
ppp ipcp compress off
sys wdog sw on
ip icmp discovery enif0 off
bridge mode 1
sys quick enable
wan adsl rate off
ether driver qroute 2
wan dmt db tlb e
sys quickbrg arp on Annex A CI Command List
Command Class List Table
System Related Command Exit Command Ethernet Related Command
WAN Related Command IP Related Command PPP Related Command
Bridge Related Command
SystemRelatedCommand Home
Command Description
sys
adjtime retrive date and time from Internet
cbuf
display [a|f|u] display cbuf a: all f: free u: used
cnt cbuf static
display display cbuf static
clear clear cbuf static
baud <1..5> change console speed
callhist
display display call history
remove <index> remove entry from call history
7/16

ZyXEL Confidential
clear clear the counters in GUI status menu
countrycode [countrycode] set country code
date [year month date] set/display date
domainname display domain name
edit <filename> edit a text file
enhanced return OK if commands are supported for PWC
purposes
errctl [level] set the error control level
0:crash no save,not in debug mode (default)
1:crash no save,in debug mode
2:crash save,not in debug mode
3:crash save,in debug mode
event
display display tag flags information
trace display system event information
display display trace event
clear <num> clear trace event
extraphnum maintain extra phone numbers for outcalls
add <set 1-3> <1st phone num> [2nd phone
num] add extra phone numbers
display display extra phone numbers
node <num> set all extend phone number to remote node
<num>
remove <set 1-3> remove extra phone numbers
reset reset flag and mask
feature display feature bit
fid
display display function id list
firmware display ISDN firmware type
hostname [hostname] display system hostname
iface
disp [#] display iface list
isr [all|used|free] display interrupt service routine
interrupt display interrupt status
log
category
access [0:none/1:log] record the access control logs
display display the category setting
error [0:none/1:log/2:alert/3:both] record and alert the system error logs
mten [0:none/1:log] record the system maintenance logs
upnp [0:none/1:log] record upnp logs
urlblocked [0:none/1:log/2:alert/3:both] record and alert the web blocked logs
urlforward [0:none/1:log] record web forward logs
clear clear log
display display all logs
errlog
clear display log error
disp clear log error
online turn on/off error log online display
load load the log setting buffer
mail
alertAddr [mail address] send alerts to this mail address
display display mail setting
logAddr [mail address] send logs to this mail address
8/16

ZyXEL Confidential
schedule display display mail schedule
schedule hour [0-23] hour time to send the logs
schedule minute [0-59] minute time to send the logs
schedule policy
[0:full/1:hourly/2:daily/3:weekly/4:non
e]
mail schedule policy
schedule week
[0:sun/1:mon/2:tue/3:wed/4:thu/5:fri/6:
sat]
weekly time to send the logs
server [domainName/IP] mail server to send the logs
subject [mail subject] mail subject
save save the log setting buffer
syslog
active [0:no/1:yes] active to enable unix syslog
display display syslog setting
facility [Local ID(1-7)] log the messages to different files
server [domainName/IP] syslog server to send the logs
mbuf
cnt
disp display system mbuf count
clear clear system mbuf count
link link list system mbuf link
pool <id> [type] list system mbuf pool
status display system mbuf status
disp <address> display mbuf status
debug [on|off]
memory <address> <length> display memory content
memwrite <address> <len> [data list ...] write some data to memory at <address>
memwl <address> write long word to memory at <address>
memrl <address> read long word at <address>
memutil
usage display memory allocate and heap status
mqueue <address> <len> display memory queues
mcell mid [f|u] display memory cells by given ID
msecs [a|f|u] display memory sections
mtstart <n-mcell> start memory test
mtstop stop memory test
mtalloc <size> [n-mcell] allocate memory for testing
mtfree <start-idx> [end-idx] free the test memory
model display server model name
proc
display display all process information
stack [tag] display process's stack by a give TAG
pstatus display process's status by a give TAG
queue
display [a|f|u] [start#] [end#] display queue by given status and range numbers
ndisp [qid] display a queue by a given number
quit quit CI command mode
reboot [code] reboot system
code = 0 cold boot,
= 1 immediately boot
= 2 bootModule debug mode
reslog
9/16

ZyXEL Confidential
disp display resources trace
clear clear resources trace
stdio [second] change terminal timeout value
time [hour [min [sec]]] display/set system time
timer
disp display timer cell
trace [on|off] set/display timer information online
start [tmValue] start a timer
stop <ID> stop a timer
trcdisp monitor packets
trclog
switch [on|off] set system trace log
online [on|off] set on/off trace log online
level [level] set trace level of trace log #:1-10
type <bitmap> set trace type of trace log
disp display trace log
clear clear trace
call display call event
encapmask [mask] set/display tracelog encapsulation mask
trcpacket
create <entry> <size> create packet trace buffer
destroy packet trace related commands
channel <name>
[none|incoming|outgoing|bothway] <channel name>=enet0,sdsl00, fr0 set packet trace direction for a given channel
string enable smt trace log
switch [on|off] turn on/off the packet trace
disp display packet trace
udp send packet trace to other system
switch [on|off] set tracepacket upd switch
addr <addr> send trace packet to remote udp address
port <port> set tracepacket udp port
parse [[start_idx], end_idx] parse packet content
brief display packet content briefly
version display RAS code and driver version
view <filename> view a text file
wdog
switch [on|off] set on/off wdog
cnt [value] display watchdog counts value: 0-34463
romreset restore default romfile
server
access <telnet|ftp|web|icmp|snmp|dns>
<value> set server access type
load load server information
disp display server information
port <telnet|ftp|web|snmp> <port> set server port
save save server information
secureip <telnet|ftp|web|icmp|snmp|dns> <ip> set server secure ip addr
spt
dump dump spt raw data
root dump spt root data
rn dump spt remote node data
user dump spt user data
slot dump spt slot data
save save spt data
10/16