ZyXEL Communications P-660RU-T V2 Series User manual

P-660RU-T v2 Quick Start Guide
0
P-660RU-T v2
ADSL2+ Ethernet / USB Router
Quick Start Guide
Version 3.40
Edition 1
11/2006

1
P-660RU-T v2 Quick Start Guide
Overview
The P-660RU-T v2 ADSL2+ Ethernet / USB router is the ideal
device for small networks or individual computers connecting
to the Internet via ADSL. Featuring USB and Ethernet ports,
computers can share local resources (such as printers and
files) and access to the Internet - simultaneously.
This Quick Start Guide shows you how to:
1 Connect the hardware
2 Set up Internet access
See your User’s Guide for background information on all
features.
1 Connect the Hardware
There are two ways to connect your computer or computer
network to the P-660RU-T v2:
Option A: Connect via Ethernet. See page 2.
Option B: Connect via USB (you will need to install the USB
driver). See page 4.

P-660RU-T v2 Quick Start Guide
2
Option A: Connect via Ethernet
1ETHERNET:Use an Ethernet cable to connect a computer
to the ETHERNET port for Internet access.
2DSL: Use a telephone wire to connect your P-660RU-T
v2’s DSL port to a telephone jack (or to a splitter, if one is
already installed).
3POWER: Use only the included power adaptor to connect
the POWER socket to an appropriate power source.
After you’ve made the connections, push in the power button
to turn on the P-660RU-T v2. Look at the lights on the front
panel.

3
P-660RU-T v2 Quick Start Guide
•ThePOWER light blinks while performing system testing. It
then turns steady on if the testing is successful.
•TheDSL light blinks then turns steady on, and blinks when
there is traffic.
•TheETHERNET light turns on if the ETHERNET port is
properly connected, and blinks when there is traffic.
VIf none of the LEDs are on, unplug the device
and recheck your hardware connections.

P-660RU-T v2 Quick Start Guide
4
Option B: Connect via USB
Note: Do NOT connect the same computer to both the
USB and ETHERNET ports on the P-660RU-T v2.
1USB:Connect the provided USB cable to the P-660RU-T
v2’s USB port.
2DSL: Use a telephone wire to connect your P-660RU-T
v2’s DSL port to a telephone jack (or to a splitter, if one is
already installed).
3POWER: Use only the included power adaptor to connect
the POWER socket to an appropriate power source.

5
P-660RU-T v2 Quick Start Guide
After you’ve made the connections, push in the power button
to turn on the P-660RU-T v2. Look at the lights on the front
panel.
•ThePOWER light blinks while performing system testing. It
then turns steady on if the testing is successful.
•TheDSL light blinks then turns steady on, and blinks when
there is traffic.
•TheUSB light turns on if the USB port is properly connected,
and blinks when there is traffic.
VIf none of the LEDs are on, unplug the device
and recheck your hardware connections.
Install the USB Software
Follow the steps below to install the USB driver.
1Save your work and close all applications.
2Connect the P-660RU-T v2 to a USB port on your
computer. A Found New Hardware Wizard screen
displays.

P-660RU-T v2 Quick Start Guide
6
VIf the wizard screen does not display do one of
the following: a) Disconnect the USB cable and
reconnect it. b) Use the Windows Device Wizard
to manually add the device. c) Restart your
computer.
3Insert the support CD into your computer CD-ROM drive
and select Install the software automatically
(Recommended) and click Next to continue.
4Windows starts installing the USB driver.
Windows 2000/XP: If a warning screen displays, click Yes or
Continue Anyway.
Windows 98 SE: If prompted, insert the Windows 98 SE CD
and click OK.
5Click Finish to complete the wizard.
2 Set Up Internet Access
You can configure the P-660RU-T v2 for Internet access in
any one of three ways:
A: Configuration Genie. See page 8.
B: Zero Configuration. See page 8.
C: Web Configurator Internet Access Wizard. See page 9.

7
P-660RU-T v2 Quick Start Guide
"Configuration genie and Zero configuration are
only able to configure the device automatically
for Internet access if you are using PPPoE,
PPPoA or ENET ENCAP encapsulation with a
dynamically-assigned IP address from your ISP.
If you are not using these Internet access
settings, then use the Web Configurator
Internet Access Wizard to manually configure
the device.
You will need your Internet access information such as user
name and password, if provided by your ISP.
INFORMATION
FROM ISP
YOU ARE USING
ENCAPSULATION
METHOD
MODE IP
ADDRESS
None RFC1483 Bridge N/A
ENET ENCAP Routing Dynamic
An IP address
only
RFC1483 Routing Static
A user name
and password
PPPoA or PPPoE Routing Dynamic
PPPoA Bridge N/A
A user name,
password and
an IP address
PPPoA or PPPoE Routing Static

P-660RU-T v2 Quick Start Guide
8
A: Configuration Genie
From the included CD, click Multimedia Auto Provisioner
(the installation and configuration assistant) and then click
Installation Tutorial. After you have viewed the tutorial, click
Configuration Genie at the end of the installation tutorial or
from Multimedia Auto Provisioner on the CD.
B: Zero Configuration
Launch your web browser and navigate to any web site (for
example, www.zyxel.com). The P-660RU-T v2 automatically
detects and configures your Internet connection. This may
take about two minutes.
An IP address,
subnet mask
and a gateway
IP address
ENET ENCAP Routing Static
INFORMATION
FROM ISP
YOU ARE USING
ENCAPSULATION
METHOD
MODE IP
ADDRESS

9
P-660RU-T v2 Quick Start Guide
If you have a PPPoE or PPPoA connection, a screen displays
prompting you to enter your Internet account information.
Enter the username, password and/or service name exactly
as provided. Click Log on to the Internet!.
C: Web Configurator Internet Access Wizard
Note: Enter the Internet access information given to you
by your ISP exactly in each wizard screen. If not
given, leave the fields set to the default.
1In your browser, go to http://192.168.1.1.