ZyXEL Communications P-2602HWNLI User manual

P-2602HWNLI
802.11g Wireless ADSL2+ 4-port VoIP IAD
Quick Start Guide
Version 3.40
09/2007
Edition 2

P-2602HWNLI Quick Start Guide
2
Overview
Your P-2602HWNLI Integrated Access Device allows you to make phone calls over the Internet (Voice over
Internet, or VoIP) as well as regular analog (PSTN) or digital (ISDN) phone calls. It also provides Internet
access for your network.
The P-2602HWNLI also allows wired and wireless clients to safely access the Internet. It can connect up to
four Ethernet devices, and includes wireless networking capability.
The following figure shows your P-2602HWNLI, labeled A, connecting your computers to the Internet and
providing firewall protection. The telephones connected to the P-2602HWNLI can also make calls over the
Internet. See the User's Guide for more information on all features.
Note: When you set up your P-2602HWNLI you may need your Internet access and (SIP-based) voice
account information.

P-2602HWNLI Quick Start Guide
3
1 Connect Your P-2602HWNLI
1DSL: Use the gray ADSL cable to connect the DSL port to a telephone jack or the DSL (or MODEM) jack
on a splitter.
2Do one of the following to connect one or more telephones to the P-2602HWNLI. These are also known as
Foreign eXchange Station (FXS) connections.
PHONE: Use telephone wire (and any included telephone adaptors) to connect analog telephones to these
ports. Use the PHONE 1 port first.

P-2602HWNLI Quick Start Guide
4
Note: When the P-2602HWNLI does not have power, only the phone connected to the
PHONE 1 port can be used for making calls. Ensure you know which phone this is, so
that in case of emergency you can make outgoing calls.
ISDN PHONE: Use telephone wire to connect one or more ISDN telephones or an ISDN PBX to this port.
3 PSTN/ISDN: You can connect either a PSTN or an ISDN line to this port. This is a Foreign eXchange Office
(FXO) port. Use the included green PSTN cable or ISDN cable to connect the PSTN/ISDN port.
• Connect the PSTN line cable’s larger end to the PSTN/ISDN port. Connect the other end to the tele-
phone jack or the TEL or PHONE socket on a splitter.
• The ISDN line cable’s connectors are of equal size. Connect either end to the PSTN/ISDN port. Con-
nect the other end to an ISDN Terminal Adapter (TA). Connect the TA’s other port to the telephone jack
or the TEL or PHONE socket on a splitter.
Note: If you are using T-ISDN (UR-2), connect the green wire to a TAE connector before connecting it
to the telephone splitter's "phone" jack or a telephone wall jack.
4ETHERNET: Use an Ethernet cable to connect a computer to an Ethernet port for initial configuration and/
or Internet access.
5POWER:Use the included power adaptor to connect the POWER socket to an appropriate power source
(see the User’s Guide for details of power adaptors by region).
6Push in the POWER button and look at the lights on either side.
•ThePOWER light blinks during start-up and stays on once the P-2602HWNLI is
ready.
•TheDSL light blinks during start-up, and stays on once the P-2602HWNLI is
ready. If the DSL light is off, there is a problem with the hardware or the phone line
connection to the ISP.
•TheETHERNET lights blink once on startup, and remain on if there is an active
Ethernet connection. When the P-2602HWNLI is sending/receiving data on an
active Ethernet connection, the light blinks.
•TheWLAN light turns steady green when the wireless LAN is ready. It blinks when
the P-2602HWNLI is sending/receiving data through the wireless LAN.
• Use the following sections in this guide to get to the screens where you configure
Internet access, wireless and VoIP settings.

P-2602HWNLI Quick Start Guide
5
2 Initial Configuration
Open your web browser, and go to http://www.zyxel.com.
Your P-2602HWNLI tries to detect your Internet connection. This takes about two minutes. If any other
screens appear, follow the directions in the screen.
If http://www.zyxel.com opens correctly, your Internet access is ready. If the web page does not open, use the
following steps. You should have information provided by your ISP.
1Enter 192.168.1.1 as the web site address
in your browser.
2Type the default user name admin and the default admin
password admin for administrator access. Click Login.
When you log in as an administrator, all features are
available.
Note: For user access, type the default user name user
and default user password 1234. Then Click Login.
Advanced features are not available in the user
mode. Refer to the Available Features Table in the
User’s Guide for more information.
3Type (and retype) a new password and
click Apply.

P-2602HWNLI Quick Start Guide
6
2.1 Voice Setup
Use the wizard setup screens to set up your SIP account with the information given to you by your ISP and
register your SIP account.
4Click Apply to replace the factory default
certificate for added security; alternatively
click Ignore to proceed if you do not want
to change the certificate now.
This screen displays only when you log in
as an administrator.
5Select Go to Wizard setup and click
Apply.
6Click INTERNET/WIRELESS SETUP
to configure your Internet access
and/or wireless settings. Follow the
directions in the screens and enter
your Internet access information
exactly as it was given to you.
7Click VOICE OVER INTERNET
SETUP to configure your VoIP
account settings. See Section 2.1.

P-2602HWNLI Quick Start Guide
7
Note: You should have a voice account already set up.
2.2 Regular Phone Line Configuration
When one of your VoIP accounts is registered, the P-2602HWNLI normally uses the Internet (not the regular
phone line) to make phone calls. Follow the directions in this section to make sure you can also use the
regular phone line while one of your VoIP accounts is registered.
Note: When the P-2602HWNLI does not have power, only the phone connected to the
PHONE 1 port can be used for making calls. Ensure you know which phone this is, so
that in case of emergency you can make outgoing calls.
In the main screen, click VoIP > PSTN Line (or ISDN Line if you want to configure for an ISDN phone).
1Select the SIP server profile of your
VoIP service provider, either SIP
Profile 1 or SIP Profile 2, and click
Apply. If your VoIP service provider is
not in the list, select None and click
Apply.
2Fill in the fields with information from
your voice service provider. Leave the
default settings in fields for which no
information was provided (except if
otherwise specified).
If you have a SIP account like
[e-mail],“1234” would
be the SIP Number and “VoIP-
provider.com” would be the SIP Service
Domain.
This screen configures SIP account 1.
Select the check box if you have a
second SIP account that you want to
use.
Note: If your selected a preconfigured SIP profile, just enter your SIP number, user name and
password. Leave the remaining fields at default.

P-2602HWNLI Quick Start Guide
8
PSTN (or ISDN)Line Pre-fix Number: If you want to make a
regular phone call after one of your VoIP accounts has been
registered you have to dial this number before you dial the
phone number.
Relay to PSTN (or ISDN)Line: Enter phone numbers for
regular phone calls (that do not use the Internet) that you
always want to dial without the prefix number. For example,
enter emergency phone numbers here.
Click Apply.
2.3 Make Calls Through the Internet
When a PHONE light turns on, your SIP account is registered
successfully. Dial a numerical SIP number (like “12345” for example) on your phone’s keypad. Use your voice
service provider’s dialing plan to make calls through the Internet to regular telephone numbers. See your
User’s Guide if you need to make peer-to-peer VoIP calls or calls to SIP numbers that use letters.
3 Troubleshooting
If you cannot access the Internet, follow these steps.
1Check the device’s lights. If they are different from what is described in Section 1, make sure the
connections are correct. If the lights are still different, turn off the device, wait a few seconds, and turn it on
again.
2Follow the steps in Section 2 again. Make sure you enter the correct information. For example, if your
account has a user name and password, make sure you type it correctly. In addition, if you are not sure
which encapsulation your ISP uses, contact your ISP.
3If you are using a new Internet account, contact your ISP to make sure it is active.
4If you still have problems, see Troubleshooting in the User’s Guide.
If you can access the Internet, but you cannot make calls through the Internet, follow these steps.
1Make sure the VOICE OVER INTERNET SETUP wizard screens are properly configured (see Section 2.1).
2One of the PHONE lights should come on. Make sure that your telephone is connected to the
corresponding PHONE or ISDN PHONE port.
3You can also check the VoIP status in the Status screen.
Viewing Your Product’s Certifications
1Go to www.zyxel.com.
2Select your product from the drop-down list box on the ZyXEL home page to go to that product's page.
3Select the certification you wish to view from this page.