ZyXEL Communications Prestige P660RU-T1 Instruction Manual

ZyXEL
Firmware Release Note
Prestige P660RU-T1
Standard Version
Release 3.40(ST.5)C0
Date: November 17, 2005
Author: Sam Shi

ZyXEL Prestige 660RU-T1 Standard Version
Release 3.40(ST.5) C0
Release Note
Date: November 17, 2005
Supported Platforms:
ZyXEL Prestige 660RU-T1
Versions:
ZyNOS Version : V3.40(ST.5) | 11/17/2005 14:57:03
Bootbase Version : V1.03 | 04/26/2005 15:20:30
Notes:
P660R/RU-T1/T3/T7 is next generation of ZyXEL P623R series with higher speed of
ADSL2, ADSL2+ technology, speed up to 12Mbps (ADSL2) and 24 Mbps (ADSL2+).
With dual interface of USB and Ethernet, P660R/RU-61/63/67 offers the flexible way to
access the Internet.
Features:
Modification in V3.40(ST.5)C0 | 11/17/2005
1. Change to FCS
Modification in V3.40(ST.5)b3 | 11/9/2005
1. [Feature Enhancement]
Add reset button test Function
2. [Feature Enhancement]
Add PPPoE pass through when PC connect to device from USB interface
3. [BUG FIX] SPRID 051109589
Symptom: In SMT menu 4 and menu3.5 the ISP’s name and ESSID can not accept
special characters such as #$%^, but in eWC can accept it, they are not accordant
Condition: N/A
4. [BUG FIX] SPRID 051109596
Symptom: put rom-t has issue
Condition: after sys rom reset, put rom-t with right configurations, but device can’t
connect to internet
5. [BUG FIX] SPRID 051109598
Symptom: device can’t get IP from DHCP server after configure with wan node
command
Condition: no valid item in hunt table, vcautohunt is active, input wan node index
1, wan node vpi 0, wan node vci 33, wan node save, but device can’t get IP

Modification in V3.40(ST.5)b2 | 11/1/2005
1 [BUG FIX] SPRID: 051021682
Symptom: The display of CI command “wan atm vc webredir” has issue.
Condition: Step1: type in command “wan atm vc webredir”. It will show “usage:
webredict<enable 1 | disable 0>”
Step2: but type in command “wan atm vc webredir 1”, the webrediret is
disable.
type in command “wan atm vc webredir 0”, the webrediret is enable
2 [BUG FIX] SPRID: 051021684
Symptom: subnet mask error
Condition: 1. Log into the device via WEB GUI
2. Config Static WAN IP Address
3. Enter subnet mask ”255.255.248.0”
Then it will pop up a message shows ”subnet mask error”. However, ”
255.255.248.0”is a valid subnet
Modification in V3.40(ST.5)b1 | 10/19/2005
1.[Feature Enhancement]
Add CI command”WAN node”
Add CI command”sys password”
2. Add multiboot ver. 2.1
3. Change modem code to 3.2.0.7
Modification in V3.40(ST.4)C0 | 09/15/2005
1. Change default rom file according to 3.40(ST.3)C0
Modification in V3.40(ST.4)b2 | 08/24/2005
1. [FETURE ENHANCE]
Modify the zero configuration web pages according to PM’s requirement.
Modification in V3.40(ST.4)b1 | 08/17/2005
1 [BUG FIX] SPRID: 050817671
Symptom: the testing in progress page will consist endless
Condition: N/A
2 [BUG FIX] SPRID:
050817672
Symptom: Web redirect can not work well
Condition: When we input system password and PPPoE username/password and
press the save button, the settings are saved, but no connection testing window is shown up,
but still a window asking for the system password and PPPoE username/password again.
At this time, even if we ‘>d d 1’ in SMT, it can’t trigger PPPoE
3 [BUG FIX] SPRID:
050817675
Symptom: PPPOE/PPPOA idle timeout do not work
Condition: Step 1.:Set PPPOE idle timeout to 15 and PPPOE/LLC right username
password in menu4, Make sure PC can access the Internet
Step 2: Close all the programs that may send packets. Waiting at least 15s
Then the PPPOE is idle.
Step 3: And now, we can not access the web even if we ‘d d 1’ in SMT
except reboot the device.
4 [FETURE ENHANCE]

Add a new page zCfgTryAgain.html. This page will be showed when DSL line has not
up. Modified the zCfgPPPOE.html. Close web redirect once PPPOE user name and
password are right
5 [BUG FIX] SPRID:
050817677
Symptom: MSN message support has some problem.
Condition: While disable or enable UPNP function in DUT, the Windows XP MSN
6.2 and MSN 7.0 can not establish Whiteboard sharing functions.
6 [BUG FIX] SPRID: 050817679
Symptom:while set the DUT LAN “Client IP Pool Starting Address” and “Size of
Client IP Pool” which are not match the “IP Subnet Mask”, but this can be saved in
GUI\Wizard Setup and rom-t. In SMT and GUI\Advanced Setup have no this issue.
Condition: N/A
7 [BUG FIX] SPRID: 050817680
Symptom： If the multicast stream speed goes up to 6Mb or higher then the P660 is not
able to keep up and the multicast stream starts to get choppy (this is brodcast tv signal
being streamed) and it gets unviewable. This goes on for awhile, then the device locks up
and you have to reboot to get it working again.
Condition: N/A
8. [FETURE CHANGED]
Change default romfile to Access Telecom version
Modification in V3.40(ST.3)C0 | 06/08/2005
1. Change to FCS
Modification in V3.40(ST.3)b2 | 06/01/2005
1. [BUG FIX] SPRID: 050525640
Symptom: Use backup function in GUI will make LAN pc and DUT WAN can not get
ip.
Condition: Step1 enter eWC->maintenance->configuration->backup.
Step2 backup current configuration.
Step3 in LAN pc can not get ip from DUT and DUT WAN can not get
dynamic ip.
2. [BUG FIX] SPRID: 050524562
Symptom: A problem about can’t get ip(enet encap/llc/dynamic)
Condition: 1. Use”sys romreset”in SMT 24.8
2. Go to WEB wizard or SMT 4, use enet encap/LLC/dynamic ip, set the
vpi/vci=0/33, then the device can’t get ip (use other vpi/vci is ok, our AUT-C set vpi/vci is
0/33).
3. [BUG FIX] SPRID: 050516864
Symptom: Use ax/4000 test UBR have problem
Condition: Set menu 4 ATM QoS Type= UBR, Peak Cell Rate (PCR) = 1000, Sustain
Cell Rate (SCR) = 500, Maximum Burst Size (MBS) =500, The traffic do not restrict by
the PCR, it can up to 1600 cells/s.
4. [FEATURE ENHENCE]
Routing Throughput Enhancement.
5. Change Default Rom-file
Add new rule into VC hunting table: VPI/VCI: 0/38 Encapsulation: PPPOA
Multiplexing: VC

Modification in V3.40(ST.3)b1 | 05/19/2005
1. [Bug Fix] SPRID: 050505225
Symptom: While use “Full Feature” mode in NAT in GUI, and configure rule in “Full
Feature”, but this NAT rule can not work. Then reboot DUT, this rule can works
properly.
Condition: Step1: In GUI/Advanced Setup/NAT, choose “Full Feature”.
Step2: In “Full Feature”, configure a NAT rule (For example: One-to-One,
or Many-to-One……).
Step3: While complete the setting, this NAT “Full Feature” rule can not
work. Then reboot DUT, this rule can works properly.
Step4: In SMT, it has no this issue.
2. [Bug Fix] SPRID: 050506301
Symptom: use pppoe encapsulation，get rom-t file from LAN pc change some
configuration and put the rom-t file, then pppoe login password will be change.
Condition: step1: use pppoe encapsulation, get rom-t file from LAN pc change some
configuration(such as system name->1234)
step2: put rom-t file from LAN pc ,after the DUT reboot, pppoe can not dial
up.
step3: change the pppoe login password then can dial up.
3. [Bug Fix] SPRID: 050310555
Symptom: in eWC can set DUT LAN ip to 0.0.0.0, in SMT menu3.2 when set it, it
warning “0.0.0.0 is not a valid IP address” they are not match.
Condition: N/A
4. [Bug Fix] SPRID: 050310549
Symptom: When 2 PCs visit eWC of DUT, the priority have some problem .
Condition: N/A
5. [Bug Fix] SPRID: 041222143
Symptom: in menu 24.11, leave the telnet server port default, upload firmware using
tftp from lan side pc, it always fails; but if telnet server port is changed to 23, the
function works well.
Condition: N/A
6. [Bug Fix] SPRID: 041124036
Symptom: 1.In Menu 24.8 typing ”ip ping 192.168.8.1” (the ip address from which
you can get response”.the default times of ping is three.
2.when the device get response in the first time or the second
time.type”ctrl+c”.then type the Up key and Enter quickly.the system will crash and
reboot.
Condition: N/A
7. [Bug Fix] SPRID: 050506307
Symptom: two LAN pc connect to DUT with anyip have problem.
Codition: step1 : use CI command “ip anyip enable yes” turn on DUT anyip
step2: LAN two pc set any ip out of DUT dhcp ip pool.
step3 when one LAN pc ping access DUT then another pc can not ping
access unless change the static ip.
8. [Bug Fix]

Symptom: there is always show testing on Web although Auto VC hunt finished and
failed.
Condition: N/A
9.[FETURE ENHANCE]
Supporting rom file back/restore via GUI .
10.[FETURE ENHANCE]
Modifying the 'Reset System' button ( MaintenanceÆdiagnosticÆGeneral) to 'Restart
the Device'.
Modification in V3.40(ST.2)C0 | 04/19/2005
1. Change to FCS firmware version.
Modification in V3.40(ST.2)b3 | 04/13/2005
2. [FEATURE CHANGE]
Symptom: Add Mbuf_Cache size for throughput improvement,
3. [FEATURE CHANGE]
Symptom: Add FTP_MALLOC.
4. [Bug Fix]
Symptom: VC-hunt causes sys exception.
5. [Bug Fix]
Symptom: The UPnP shows wrong link speed on WinXP PC.
6. [Bug Fix]
Symptom: Dialing messages shows up on console during VC-Hunt with PPPOE and
PPPOA
7. [Bug Fix]
Symptom: If we unplug ADSL line right after the ADSL just entered "wait for init
state" than ADSL will hold on this state and doesn't switch to down state, the CPU
loading is about 20% at the same time.
Modification in V3.40(ST.2)b2 | 03/17/2005
8. [FEATURE CHANGE]
Symptom: Add Mbuf_Cache to improve the throughput.
9. [Bug Fix]
Symptom: ATM Priority (UBR vs. CBR) scenario not correct.
10. [Bug Fix]
Symptom: In web wizard - LAN page. Change LAN IP for 192.168.1.1 to
192.168.181.1, the PC gets IP from the device but can't use IE to access device.
11. [Bug Fix]
Symptom: NAT_RuleList page display error in Mozilla.
12. [Bug Fix]
Symptom: In Lan page if type "255.255.248.0" in IP Subnet Mask will show "Subnet
Mask error".
13. [Bug Fix]
Symptom: Apply policy route rule to menu 3.2 or 11.3, the packet from LAN or WAN
can't route to gateway set in policy rule.
14. [Bug Fix]
Symptom: Set the MIB object “sysName” fail, this object doesn’t change but prompt
name of CI changed as what it set.

15. [Bug Fix]
Symptom: ATU-R can't link up after run the Loop test script for a spell.
16. [Bug Fix]
Symptom: Attainable downstream rate is 0 in ADSL2/ ADSL2+ mode, but it's normal
in ADSL1 mode.
17. [Bug Fix]
Symptom: ADSL sync up mode reset to default (ADSL2+) while sync up again.
Modification in V3.40(ST.2)b1 | 02/21/2005
1. [FEATURE CHANGE]
Symptom: Change DMT code form v3.0.10.3_A_TC to 3.0.11.22_A_TC for
supporting ADSL2/2+
Modification in V3.40(ST.1)b1 | 12/23/2004
2. [FEATURE CHANGE]
Symptom: Change default ROM file to disable UPNP.
3. [FEATURE CHANGE]
Symptom: Change the messages display format in CI Command “wan adsl chandata”
while the link up mode is ADSL2 and ADSL2+.
Modification in 3.40(ST.0)b1|10/22/2004
1. [FEATURE CHANGED]
Firmware downloads mechanism in Bootext is ready.
Modification in 3.40(ST.0)a2| 09/11/2004
2. [FEATURE CHANGED]
Symptom: Remove the centralize log and cli-for-smt for more system free memory.
Modification in 3.40(ST.0)a1 | 07/27/2004
1. Create this project.

ZyXEL Confidential
340ST5C0.doc 8/25
Internal Information:
1. Support ADSL2+ by TrendChip modem code DMT FwVer: 3.2.0.7_A_TC, HwVer:
T14F7_0.0
2. Support Multiboot client V2.1
Known Issues:
1. Ethernet and USB interfaces stop while ADSL is initializing.
2. The TR-067 Loop test failure.
3. If there are two or more PVCs with CBR or VBR QOS type and the total PCR
requirement exceed the line rate then the bandwidth distribution between those PVCs is
unpredictable.
4. Setup two PVCs with 1483 bridge, each PVC with 500Kbps upstream and 10Mbps
downstream traffic. If packet size is 1500 The CPU loading is 88%. The CPU loading
is 100% if packet size is 1024.
5. The VBR property of TrendChip is different form the others.
6. The value of MBS can’t be too large. Ex 10000.
7. F/W upgrade in eWC can not work with IE 5.0.3315.
8. MAC OS can’t login the WEBGUI through IE 5.2.
9. In MAC OS 10.1, USB interface can’t be detected after unplug USB cable.
10. In MAC OS 10.1, MAC PC will crash if USB cable was unplugged during data
exchanging between MAC PC and device by USB interface.
11. For CHT spec, there are two point fail but almost can reach the criteria
12. Use ax/4000 test VBR have problem.
13. Use ax/4000 test priority have problem in especially setting.
14. DUT will reboot automatically when DUT wan port is initialing and exist packet attack
from wan port, until the packet stops send to wan port of DUT, the DUT will recover
15. The Throughput does not meet the ADSL2+ criteria
16. The USB interface can't play IPTV (IGMP).
17. The debug information “[BrgStopShortCut] : Recover USB” has not been closed and it
affect auto test running smoothly.
18. In GUI, The WAN Backup functions need at least one none-zero Check WAN IP.
Modifications:
Modification in V3.40(ST.3)C0 | 06/08/2005
1. Change to FCS
Modification in V3.40(ST.3)b2 | 06/01/2005
1. [BUG FIX] SPRID: 050525640
Symptom: Use backup function in GUI will make LAN pc and DUT WAN can not get
ip.
Condition: Step1 enter eWC->maintenance->configuration->backup.
Step2 backup current configuration.
Step3 in LAN pc can not get ip from DUT and DUT WAN can not get
dynamic ip.
2. [BUG FIX] SPRID: 050524562

ZyXEL Confidential
340ST5C0.doc 9/25
Symptom: A problem about can’t get ip(enet encap/llc/dynamic)
Condition: 1. Use”sys romreset”in SMT 24.8
2. Go to WEB wizard or SMT 4, use enet encap/LLC/dynamic ip, set the
vpi/vci=0/33, then the device can’t get ip (use other vpi/vci is ok, our AUT-C set vpi/vci is
0/33).
3. [BUG FIX] SPRID: 050516864
Symptom: Use ax/4000 test UBR have problem
Condition: Set menu 4 ATM QoS Type= UBR, Peak Cell Rate (PCR) = 1000, Sustain
Cell Rate (SCR) = 500, Maximum Burst Size (MBS) =500, The traffic do not restrict by
the PCR, it can up to 1600 cells/s.
4. [FEATURE ENHENCE]
Routing Throughput Enhancement.
5. Change Default Rom-file
Add new rule into VC hunting table: VPI/VCI: 0/38 Encapsulation: PPPOA
Multiplexing: VC
Modification in V3.40(ST.3)b1 | 05/19/2005
1. [Bug Fix] SPRID: 050505225
Symptom: While use “Full Feature” mode in NAT in GUI, and configure rule in “Full
Feature”, but this NAT rule can not work. Then reboot DUT, this rule can works
properly.
Condition: Step1: In GUI/Advanced Setup/NAT, choose “Full Feature”.
Step2: In “Full Feature”, configure a NAT rule (For example: One-to-One,
or Many-to-One……).
Step3: While complete the setting, this NAT “Full Feature” rule can not
work. Then reboot DUT, this rule can works properly.
Step4: In SMT, it has no this issue.
2. [Bug Fix] SPRID: 050506301
Symptom: use pppoe encapsulation，get rom-t file from LAN pc change some
configuration and put the rom-t file, then pppoe login password will be change.
Condition: step1: use pppoe encapsulation, get rom-t file from LAN pc change some
configuration(such as system name->1234)
step2: put rom-t file from LAN pc ,after the DUT reboot, pppoe can not dial
up.
step3: change the pppoe login password then can dial up.
3. [Bug Fix] SPRID: 050310555
Symptom: in eWC can set DUT LAN ip to 0.0.0.0, in SMT menu3.2 when set it, it
warning “0.0.0.0 is not a valid IP address” they are not match.
Condition: N/A
4. [Bug Fix] SPRID: 050310549
Symptom: When 2 PCs visit eWC of DUT, the priority have some problem .
Condition: N/A
5. [Bug Fix] SPRID: 041222143
Symptom: in menu 24.11, leave the telnet server port default, upload firmware using
tftp from lan side pc, it always fails; but if telnet server port is changed to 23, the
function works well.

ZyXEL Confidential
340ST5C0.doc 10/25
Condition: N/A
6. [Bug Fix] SPRID: 041124036
Symptom: 1.In Menu 24.8 typing ”ip ping 192.168.8.1” (the ip address from which
you can get response”.the default times of ping is three.
2.when the device get response in the first time or the second
time.type”ctrl+c”.then type the Up key and Enter quickly.the system will crash and
reboot.
Condition: N/A
7. [Bug Fix] SPRID: 050506307
Symptom: two LAN pc connect to DUT with anyip have problem.
Codition: step1 : use CI command “ip anyip enable yes” turn on DUT anyip
step2: LAN two pc set any ip out of DUT dhcp ip pool.
step3 when one LAN pc ping access DUT then another pc can not ping
access unless change the static ip.
8. [Bug Fix]
Symptom: there is always show testing on Web although Auto VC hunt finished and
failed.
9. [FETURE ENHANCE]
Supporting rom file back/restore via GUI .
10.[FETURE ENHANCE]
Modifying the 'Reset System' button ( MaintenanceÆdiagnosticÆGeneral) to 'Restart
the Device'.
Condition: N/A
Modification in V3.40(ST.2)b1 | 02/21/2005
1. [BUG FIXED]
Symptom: Input the CI command "wan atm vc result" while DSL do not sync up, the
system will hang up.
Modification in V3.40(ST.1)C0| 01/14/2005
1. Change to FCS firmware version.
Modification in V3.40(ST.1)b4| 01/12/2005
1. [BUG FIXED]
Symptom: VC hunt causes system reboot, if the right hunting information in 10th entry
of VC hunt Table and VC hunt debug open.
2. [BUG FIXED]
Symptom: VC hunt has finished successful but connection fail page is redirected by
WEB.
Modification in V3.40(ST.1)b3| 01/05/2005
3. [BUG FIXED]
Symptom: Login device by FTP and enter ls or dir, then system reboot.
4. [BUG FIXED]
Symptom: When we get ROM-t from LAN side by FTP, and modified it by WordPad,
then put ROM -t, the device won’t accept the new ROM-t.
Modification in V3.40(ST.1)b2 | 01/04/2005
1. [BUG FIXED]
Symptom: When get ROM-t from LAN side by FTP, and modify it, then put ROM-t,
the DUT will show not enough memory.