ZyXEL Communications VES-1616PE-54 Manual

VES-1616PE-54
Support Notes
Edition 1

2
General Application...............................................................................................................5
Firmware Upgrade ............................................................................................................5
Using the Web Configurator ..........................................................................................5
Using the Console Port: .................................................................................................5
Using FTP:......................................................................................................................6
Restore a Configuration File ..............................................................................................6
Using the Web Configurator: .........................................................................................6
Using the Console Port: .................................................................................................7
Using FTP:......................................................................................................................7
Backing Up a Configuration File .........................................................................................7
Using the Web Configurator: .........................................................................................7
Using the Console Port: .................................................................................................8
Using FTP:......................................................................................................................9
Load Factory Defaults........................................................................................................9
Using the Web Configurator: .........................................................................................9
DHCP Relay per VLAN..........................................................................................................11
DHCP Relay per VLAN..........................................................................................................11
Scenario .......................................................................................................................... 11
Triple Play ........................................................................................................................... 16
Triple Play concept .......................................................................................................... 16
PPPoE service.................................................................................................................. 16
Idea behind the PPPoE service.....................................................................................17
Content

3
Hardware/Firmware for deployment........................................................................... 17
Scenario .......................................................................................................................... 18
IP domain topology .........................................................................................................19
SMG-700 configuration................................................................................................20
1. Interface Configuration.......................................................................................20
2. PPPoE Setting Configuration............................................................................... 20
3. ISP Info Setting Configuration............................................................................. 21
4. Win RADIUS........................................................................................................22
VES-1616PE-54 configurations.....................................................................................24
1. VLAN configuration ............................................................................................24
P-870HW-51aV2 configurations................................................................................... 25
1. WAN configuration.............................................................................................25
2. Verification......................................................................................................... 26
3. Win RADIUS........................................................................................................27
Multicast Service ............................................................................................................. 28
1. IGMP Proxy Settings ...........................................................................................28
2. MVR Settings......................................................................................................29
VoIP Service .................................................................................................................... 33
1. VLAN configuration ............................................................................................33
2. Classifier configuration ....................................................................................... 35
3. Policy Rule configuration....................................................................................36
VLAN Stacking .....................................................................................................................38
Double Tagging application notes....................................................................................38
Scenario .......................................................................................................................... 38
1. VLAN Stacking configuration............................................................................... 38
2. Static VLAN configuration................................................................................... 40
3. Verification......................................................................................................... 41
VDSL Template....................................................................................................................42
VDSL Template application notes ....................................................................................42

4
Scenario .......................................................................................................................... 42
1. VDSL Profile Configuration for Primary Template................................................43
2. VDSL Profile Configuration for Secondary Template............................................ 45
3. VDSL Line Setup Configuration............................................................................47
FAQ..................................................................................................................................... 48
Frequently Asked Questions............................................................................................ 48
1. What is the default setting of the IP parameters?............................................... 48
2. What is the default login Name and Password of the Web Configurator? ........... 48
3. How to access my VES through the console port?............................................... 48
4. What is default login password for console, telnet, and FTP?.............................. 48
5. How to change the password?............................................................................49
6. How to access the Command Line Interface (CLI)?.............................................. 49
7. If I forgot the password, how to reset the password to default? .........................49
8. How do I configure an IP address? ...................................................................... 50
9. Is Online Help available on the Web Configurator? ............................................. 50
10. How to restart device from the Web Configurator? ............................................51
11. How to check the current running firmware version? .........................................51
12. Is the mini GBIC transceiver hot-swappable? ......................................................51
13. What is "Dual-Personality interface" on a VDSL Switch? .....................................51
14. Can I enable MVR and IGMP snooping at the same time?...................................52

5
Firmware Upgrade
Using the Web Configurator
a. Download (and unzipped) the correct model firmware to your computer.
b. Click Management > Maintenance in the navigator panel to display the following
screen.
c. Click the Click Here link for Firmware Upgrade
d. In the File Path field, click Browse to locate the firmware file.
e. Click Upgrade to start the firmware upgrade process.
Using the Console Port:
a. Download (and unzipped) the correct model firmware to your computer.
b. Connect to the console port and launch a Terminal Emulation software
c. Restart the switch to enter the debug mode via the terminal.
d. Enter “ATUR”.
e. Use the X-modem protocol to transfer (Send File) the firmware.
f. Enter “ATGO” to restart the switch after the file transfer is complete and the
General Application
1

6
firmware upgrade process is done.
Using FTP:
a. Download (and unzipped) the correct model firmware to your computer.
b. Launch the FTP client on your computer to log into switch. (From the command
prompt, type “ftp <Switch IP>”).
c. Press [ENTER] when prompted for a user name.
d. Enter the administrator login password to access the switch and display FTP
prompt.
e. Enter “bin” to set the transfer mode to binary.
f. Use “put” to transfer the firmware from the computer to the switch, for example:
“put firmware.bin ras-0” (or ras-1) transfers the firmware on your computer
(firmware.bin) to the switch and renames it to “ras”.
g. Enter “bye” to log out from the switch.
Restore a Configuration File
Using the Web Configurator:
a. Click Management > Maintenance in the navigator panel to display the following
screen.
b. Click the Click Here link for Restore Configuration

7
c. In the File Path field, click Browse to locate the firmware file.
d. Click Restore to start restoring configuration.
Using the Console Port:
a. Connect to the console port and launch a Terminal Emulation software.
b. Restart the switch to enter the debug mode via the terminal.
c. Enter “ATLC”
d. Use X-modem protocol to transfer (Send File) the configuration file (with a .rom
file extension).
e. Enter “ATGO” to restart the switch after file transfer and the configuration restore
processes are complete.
Using FTP:
a. Download (and unzipped) the correct model firmware to your computer.
b. Launch the FTP client on your computer to log into the switch. (From the
command prompt, type “ftp <Switch IP>”.
c. Press [ENTER] when prompted for a user name
d. Enter the administrator login password to access the switch and display FTP
prompt.
e. Enter “bin” to set the transfer mode to binary.
f. Use “put” to transfer the configuration file from the computer to the switch, for
example: “put comfig.rom rom-0” transfers the configuration file on your
computer (config.rom) to the switch and renames it to “rom-0”.
g. Enter “bye” to log out from the switch.
Backing Up a Configuration File
Using the Web Configurator:
a. Click Management > Maintenance in the navigator panel to display the following
screen.

8
b. Click the Click Here link for Backup Configuration to display the following screen.
c. Click Backup to display the File Download dialog. Then, click Save to back up the
configuration text file to a location you specify on your computer.
Using the Console Port:
a. Connect to the console port and launch a Terminal Emulation software.
b. Restart the switch to enter the debug mode via the terminal.
c. Enter “ATTD”.
d. Use X-modem protocol to transfer (Receive File) the configuration file (with
a .rom file extension).
e. Enter “ATGO” to restart the switch after file transfer and the configuration backup
processes are complete.

9
Using FTP:
a. Download (and unzipped) the correct model firmware to your computer.
b. Launch the FTP client on your PC to log into the switch. (From the command
prompt, type “ftp <Switch IP>”
c. Press [ENTER] when prompted for a user name
d. Enter the administrator login password to access the switch and display FTP
prompt.
e. Enter “bin” to set the transfer mode to binary.
f. Use “get” to transfer the configuration file from the switch to your computer, for
example: “get rom-0 config.rom” transfers the configuration file on the switch
(rom-0) to your computer and renames it “config.rom”.
g. Enter “bye” to log out from the switch.
Load Factory Defaults
Using the Web Configurator:
a. Click Management > Maintenance in the navigation panel to display the
following screen.
b. Click Click Here link for Load Factory Default.
c. A dialog box pops up with the “Are you sure you want to load factory defaults?”

10
prompt.
d. Click OK.
e. Click OK again to start the configuration reset process. After it is complete, the
device automatically restarts.
f. Please note that the IP address of the switch is now 192.168.1.1.

11
DHCP Relay per VLAN
The feature of DHCP relay per VLAN basis comes handy for managing the DHCP IP
assignment to the clients. VES-1616PE-54 has the ability to relay the DHCP request
packets according to its VLAN tag to the DHCP server in the uplink Network.
Scenario
The purpose is to have a DHCP relay on the VES according to VLAN=700, to the DHCP
server (IP=192.168.1.101). The VES’ In-band is 192.168.1.100, and tags a PVID=700 to
the ingress traffic on port 1. The NB shall receive the IP assigned from the DHCP
server.
DHCP Relay per VLAN
2

12
1. Configure a Static VLAN
a. In the navigation panel, click Advanced Application > VLAN > Static VLAN. The
Static VLAN screen appears.
b. Click to select the ACTIVE checkbox.
c. Type “700” in the Name field.
d. Type “700” in the VLAN Group ID field.
e. In the Port 1 field, select Fixed and click to clear the Tx Tagging checkbox.
f. In the Port 26 field, select Fixed.
g. Leave the Tx Tagging checkbox of Port 26 checked.
h. Click the Add button.

13
2. VLAN Port Setting
a. In the navigation panel, click Advanced Application > VLAN > VLAN Port Setting.
The VLAN Port Setting screen appears.
b. Type “700” in the PVID field of Port 1.
c. Click the Apply button.

14
3. Configure an In-band IP Address
a. In the navigation panel, click Basic Setting > IP Setup.
b. In the In-band IP Addresses section, type “192.168.1.100” in the IP Address field.
c. Type “255.255.255.0” in the IP Subnet Mask field.
d. Type “700” in the VID field.
e. Type “192.168.1.101” in the Default Gateway field.
f. Click the Add button.
4. DHCP VLAN Setting
a. In the navigation panel, click IP Application > DHCP > VLAN. The VLAN Setting
screen appears.
b. Type “700” in the VID field.
c. Type “192.168.1.101” in the Remote DHCP Server 1 field.
d. Click the Add button.

15
5. Save Configuration
Click the Save link in the top right-hand corner of the screen to save your
configuration into the Switch’s nonvolatile memory.

16
Triple Play concept
The concept for the setting up a triple play service in VES-1616PE-54, is to manage
the Internet, IPTV and VoIP traffic that are assigned into different VLANs. We will
give an example of a service deployed in the fields, according to the following
diagram.
PPPoE service
PPPoE application to INTERNET access is a common scene in the nowadays ADSL
service deployment, but as xDSL has progressed to the VDSL technology, it is finally
time to have the PPPoE application also implemented in the VDSL scenario. ZyXEL,
the world's leading broadband access solutions provider, can demonstrate this
scenario with products uniquely on its own.
Triple Play
3

17
Idea behind the PPPoE service
The goal of this case study is to demonstrate a proof of concept on a PPPoE service
applied on ZyXEL own VDSL2 and BRAS devices. The scenario is focused on 3 devices:
VES-1616PE-54, P-870HW-51aV2 and SMG-700. The client shall be able to enjoy
INTERNET access, by simply plugging the Ethernet cable to the CPE, i.e.
P-870HW-51aV2.
Hardware/Firmware for deployment
Hardware Firmware
BRAS Server SMG-700 1.00(TF.4)c0 | 06/07/2007
VDSL COE VES-1616PE-54 3.80(BHW.0)b5 | 08/18/2009
VDSL CPE P-870HW-51aV2 1.00(AWZ.1)C0 | 03/24/2009
Note: the radius server used for this demo is “WinRadius v4.00”

18
Scenario
The WAN interface in P-870HW-51aV2 shall be configured into PPPoE mode with the
correct username and password, which the egress traffic will automatically be
tagged with VLAN=100. VES-1616PE-54 untags the coming PPPoE traffic from the
CPE, and relay it to the BRAS, SMG-700. The SMG-700 shall be able to establish the
PPPoE connection by authenticating the username/password with the help of the
Win RADIUS server, and relay the traffic to the NAT router, to allow the client to be
able to access INTERNET.

19
IP domain topology
The IP topology is described in details on the above diagram, keeping in mind that
the NAT router at this demo has the ability to route the 172.168.23.0 domain to the
INTERNET with NAT feature. Notice that the WinRADIUS is a (free) software that can
be installed in Windows OS, in this case, WinXP.

20
SMG-700 configuration
1. Interface Configuration
a. Go to Network Setting > Interface Configuration
b. Select “up1” for the uplink Interface
c. Input the IP Address for the uplink interface, e.g. ”172.168.23.10”
d. Input the IP Subnet Mask for the uplink interface, e.g. “255.255.255.0”
e. Click Apply
f. Select “down1” for the downlink Interface
g. Input the IP Address for the downlink interface, e.g. “172.168.23.10”
h. Input the IP Subnet Mask for the downlink interface, e.g. “255.255.255.0”
i. Click Apply
2. PPPoE Setting Configuration
a. Go to Service Setting > PPPoE Setting
b. Type the AC name (access concentrator) of the PPPoE service, e.g. “test.com”
c. Select the Increment IP address and start from and input the IP, e.g.
“192.168.3.100”
d. Input the Maximum Concurrent Sessions, e.g. “3000”
e. Check the Allow Duplicate MAC Address box
f. Click Apply