1 BY ONE 102US-0002 User manual

Instruction manual
SKU: 102US-0002 / 102UK-0002
1byone Products Inc.
2313 E,Philadelphia Street,Unit M, Ontario,CA 91761
www.1byone.com
All doorchime with Easy Chime Logo working together

Thank you for purchasing 1byone Wireless Doorbell.
Please read this instruction manual before use to ensure
safe operation. Voltage of receiver
Voltage of push button
Frequency
Operating range
Power consumption:
Receiver’s ring volume
Working temperature
DC 4.5V (3 x AA batteries)
DC 3V (CR2032 battery)
433.92MHz+100KHz
150m/492ft (without obstacles)
Receiver: ＜0.3W
Push button: ＜10mA
＞85dB within 0.5m/1.6ft
-20℃~50℃
1. Package Contents:
1 x Push Button 1 x Doorbell Receiver
1 x 3V Battery for Push Button (Type: CR2032)
3 x Wall plugs 3 x Screws
1 x Double-sided Adhesive 1 x Instruction Manual
If any package contents are visibly damaged or missing,
please immediately contact 1byone Customer Service at
[e-mail] for assistance.
2. Parts Names:
Parameters:
3. Power Supply:
Receiver:The receiver is powered by 3 x AA batteries, Please
insert the battery using the following procedure:
a) Press the buckle on the battery compartment cover and
remove the battery compartment cover at the back of
the receiver.
b) Insert the 3 x AA batteries using the correct polarity to
eliminate the danger of fire.
c) Reattach the battery compartment cover.
Push button:The push button is powered by a 3V battery
(Type:CR2032). Please insert the battery using the
following procedure:
a) Take off the rain cover from the push button.
b) Twist off the back cover of the push button.
c) Insert the 3V battery (type CR2032) into the battery
compartment, making sure the battery surface marked
with a“+”is facing upwards.
d) Put back the back cover and tighten it, making sure it is
securely closed to ensure the waterproof IP 44 protection.
Safety note:
• Weak batteries for the receiver can greatly reduce the
ringtone volume, please change the same voltage and
type batteries every 8-10 months.
• Weak battery for the push button can reduce the
operating distance. If the performance of the push button
deteriorates or completely stops, please replace with
another 3V type CR2032 battery.
• Always insert the battery using the correct polarity to
eliminate the danger of fire.
• Keep old and new batteries away from children.
• Old batteries should be properly disposed using safe
environmental practices.
• Remove the batteries from the receiver and push button if
the doorbell system is not to be used for an extended
period of time.
4. Operation:
A. Selecting the notification mode:
The doorbell receiver can notify after the push button has
been pressed by playing a ringing sound, flashing an LED,
or ringing and flashing an LED at the same time.These are
referred to as Sound, Flash, and Sound+ Flash mode.
When the Sound and flash button is pressed, the
receiver will play a“beep”sound signifying Sound Only
mode; flash a LED signifying Flash Only mode; play a“beep”
sound and flash a LED at the same time signifying Sound +
Flash mode. Press the Sound and flash button until you
reach your preferred notification mode.
B. Selecting the ringtone:
There are 36 programmable ringtones for selection.
Press the ringtone selector button to change the
ringtone. Stop pressing this button when you have reached
the desired ringtone.
C. Adjusting ringtone volume:
Press the volume button until the desired volume is
set.There are 6 volume levels for selection.
D. Re-pairing Function:
If a receiver starts ringing even when the push button isn’t
pressed, or a push button interferes with other receivers, it
may be necessary to reset the current pairings and pair
again.
To reset the push button:
Press the Paring button on the receiver and hold for 5
seconds.The LED light will come on and beep five times
then all pairing information for the push button(s) will be
deleted.Next, unplug or remove the batteries from the
receiver and then reattach it to power after 30 seconds.The
LED light will come on for 15 seconds and beep once.This
means the receiver is in pairing mode. Next press the push
button. If pairing is successful, the receiver should ring. It
normally takes about 10-15 seconds for the push button
and receiver to pair. If there is no pairing within 15 seconds,
the LED will turn off and beep twice and automatically exit
pairing mode. Please try pairing again.
5. Installation:
Receiver:The receiver can be mounted on a wall or just put
in a flat place.
To be mounted on a wall:
Select a suitable location for the doorbell, usually close to
your door. Drill holes on the wall. Next push the wall plugs
into the drilled holes and then insert the screws into the
wall plugs. Finally, mount the receiver on the screw.
Push button:Install the push button with double-sided
adhesive or by screws:
a. With double-sided adhesive:
• Select a suitable location for the push button, usually
close to your outside door.
• Stick the push button to the wall using the included
double-sided adhesive.
b. By screws:
• Select a suitable location for the doorbell, usually close to
your outside door.
• Pierce the two small grooves (A) on the inner side of the
back cover with a pointed object. Drill holes on the wall.
Next push the wall plugs into the drilled holes and screw
the back cover onto the wall with screws.
• Put the front cover onto the back cover and tighten it,
making sure it is securely closed to ensure the
waterproof IP 44 protection.
PAIR MODE VOL
1
01 02
2 3 4 5 6
7
8
9
1. Speaker
2. LED indicator
3. Ringtone selector button
4. Pair button
5. Sound and flash button
6.Volume button
7. Name plate position
8. Rain cover
9. Push button
▲ Push button
▲ Receiver

Parameters:
3. Power Supply:
Receiver:The receiver is powered by 3 x AA batteries, Please
insert the battery using the following procedure:
a) Press the buckle on the battery compartment cover and
remove the battery compartment cover at the back of
the receiver.
b) Insert the 3 x AA batteries using the correct polarity to
eliminate the danger of fire.
c) Reattach the battery compartment cover.
Push button:The push button is powered by a 3V battery
(Type:CR2032). Please insert the battery using the
following procedure:
a) Take off the rain cover from the push button.
b) Twist off the back cover of the push button.
c) Insert the 3V battery (type CR2032) into the battery
compartment, making sure the battery surface marked
with a“+”is facing upwards.
d) Put back the back cover and tighten it, making sure it is
securely closed to ensure the waterproof IP 44 protection.
Safety note:
• Weak batteries for the receiver can greatly reduce the
ringtone volume, please change the same voltage and
type batteries every 8-10 months.
• Weak battery for the push button can reduce the
operating distance. If the performance of the push button
deteriorates or completely stops, please replace with
another 3V type CR2032 battery.
• Always insert the battery using the correct polarity to
eliminate the danger of fire.
• Keep old and new batteries away from children.
• Old batteries should be properly disposed using safe
environmental practices.
• Remove the batteries from the receiver and push button if
the doorbell system is not to be used for an extended
period of time.
4. Operation:
A. Selecting the notification mode:
The doorbell receiver can notify after the push button has
been pressed by playing a ringing sound, flashing an LED,
or ringing and flashing an LED at the same time.These are
referred to as Sound, Flash, and Sound+ Flash mode.
When the Sound and flash button is pressed, the
receiver will play a“beep”sound signifying Sound Only
mode; flash a LED signifying Flash Only mode; play a“beep”
sound and flash a LED at the same time signifying Sound +
Flash mode. Press the Sound and flash button until you
reach your preferred notification mode.
B. Selecting the ringtone:
There are 36 programmable ringtones for selection.
Press the ringtone selector button to change the
ringtone. Stop pressing this button when you have reached
the desired ringtone.
C. Adjusting ringtone volume:
Press the volume button until the desired volume is
set.There are 6 volume levels for selection.
D. Re-pairing Function:
If a receiver starts ringing even when the push button isn’t
pressed, or a push button interferes with other receivers, it
may be necessary to reset the current pairings and pair
again.
To reset the push button:
Press the Paring button on the receiver and hold for 5
seconds.The LED light will come on and beep five times
then all pairing information for the push button(s) will be
deleted.Next, unplug or remove the batteries from the
receiver and then reattach it to power after 30 seconds.The
LED light will come on for 15 seconds and beep once.This
means the receiver is in pairing mode. Next press the push
button. If pairing is successful, the receiver should ring. It
normally takes about 10-15 seconds for the push button
and receiver to pair. If there is no pairing within 15 seconds,
the LED will turn off and beep twice and automatically exit
pairing mode. Please try pairing again.
5. Installation:
Receiver:The receiver can be mounted on a wall or just put
in a flat place.
To be mounted on a wall:
Select a suitable location for the doorbell, usually close to
your door. Drill holes on the wall. Next push the wall plugs
into the drilled holes and then insert the screws into the
wall plugs. Finally, mount the receiver on the screw.
Push button:Install the push button with double-sided
adhesive or by screws:
a. With double-sided adhesive:
• Select a suitable location for the push button, usually
close to your outside door.
• Stick the push button to the wall using the included
double-sided adhesive.
b. By screws:
• Select a suitable location for the doorbell, usually close to
your outside door.
• Pierce the two small grooves (A) on the inner side of the
back cover with a pointed object. Drill holes on the wall.
Next push the wall plugs into the drilled holes and screw
the back cover onto the wall with screws.
• Put the front cover onto the back cover and tighten it,
making sure it is securely closed to ensure the
waterproof IP 44 protection.
MODE
VOL
03 04

Parameters:
3. Power Supply:
Receiver:The receiver is powered by 3 x AA batteries, Please
insert the battery using the following procedure:
a) Press the buckle on the battery compartment cover and
remove the battery compartment cover at the back of
the receiver.
b) Insert the 3 x AA batteries using the correct polarity to
eliminate the danger of fire.
c) Reattach the battery compartment cover.
Push button:The push button is powered by a 3V battery
(Type:CR2032). Please insert the battery using the
following procedure:
a) Take off the rain cover from the push button.
b) Twist off the back cover of the push button.
c) Insert the 3V battery (type CR2032) into the battery
compartment, making sure the battery surface marked
with a“+”is facing upwards.
d) Put back the back cover and tighten it, making sure it is
securely closed to ensure the waterproof IP 44 protection.
Safety note:
• Weak batteries for the receiver can greatly reduce the
ringtone volume, please change the same voltage and
type batteries every 8-10 months.
• Weak battery for the push button can reduce the
operating distance. If the performance of the push button
deteriorates or completely stops, please replace with
another 3V type CR2032 battery.
• Always insert the battery using the correct polarity to
eliminate the danger of fire.
• Keep old and new batteries away from children.
• Old batteries should be properly disposed using safe
environmental practices.
• Remove the batteries from the receiver and push button if
the doorbell system is not to be used for an extended
period of time.
4. Operation:
A. Selecting the notification mode:
The doorbell receiver can notify after the push button has
been pressed by playing a ringing sound, flashing an LED,
or ringing and flashing an LED at the same time.These are
referred to as Sound, Flash, and Sound+ Flash mode.
When the Sound and flash button is pressed, the
receiver will play a“beep”sound signifying Sound Only
mode; flash a LED signifying Flash Only mode; play a“beep”
sound and flash a LED at the same time signifying Sound +
Flash mode. Press the Sound and flash button until you
reach your preferred notification mode.
B. Selecting the ringtone:
There are 36 programmable ringtones for selection.
Press the ringtone selector button to change the
ringtone. Stop pressing this button when you have reached
the desired ringtone.
C. Adjusting ringtone volume:
Press the volume button until the desired volume is
set.There are 6 volume levels for selection.
D. Re-pairing Function:
If a receiver starts ringing even when the push button isn’t
pressed, or a push button interferes with other receivers, it
may be necessary to reset the current pairings and pair
again.
To reset the push button:
Press the Paring button on the receiver and hold for 5
seconds.The LED light will come on and beep five times
then all pairing information for the push button(s) will be
deleted.Next, unplug or remove the batteries from the
receiver and then reattach it to power after 30 seconds.The
LED light will come on for 15 seconds and beep once.This
means the receiver is in pairing mode. Next press the push
button. If pairing is successful, the receiver should ring. It
normally takes about 10-15 seconds for the push button
and receiver to pair. If there is no pairing within 15 seconds,
the LED will turn off and beep twice and automatically exit
pairing mode. Please try pairing again.
5. Installation:
Receiver:The receiver can be mounted on a wall or just put
in a flat place.
To be mounted on a wall:
Select a suitable location for the doorbell, usually close to
your door. Drill holes on the wall. Next push the wall plugs
into the drilled holes and then insert the screws into the
wall plugs. Finally, mount the receiver on the screw.
Push button:Install the push button with double-sided
adhesive or by screws:
a. With double-sided adhesive:
• Select a suitable location for the push button, usually
close to your outside door.
• Stick the push button to the wall using the included
double-sided adhesive.
b. By screws:
• Select a suitable location for the doorbell, usually close to
your outside door.
• Pierce the two small grooves (A) on the inner side of the
back cover with a pointed object. Drill holes on the wall.
Next push the wall plugs into the drilled holes and screw
the back cover onto the wall with screws.
• Put the front cover onto the back cover and tighten it,
making sure it is securely closed to ensure the
waterproof IP 44 protection.
Notes:
• The push button and receiver can connect with a range
up to 150m/492ft without any obstacles.
• The push button’s transmitting frequency is 433MHz and
its range can be affected by metal ,walls, concretes, and
interfering signals from other electronic appliances with
the same frequency including televisions, radios, and
cookers.
• Please do not install the push button and receiver near to
the above mentioned electronic appliances.
• Please test the operating range of the receiver and push
button in your home before installation.
• Do not install the push button and receiver near any
source of naked flames such as lighted candles.
• Do not expose the push button and receiver to direct
sunlight or high temperatures, otherwise overheating
may cause them irreparably damaged.
c. Install the name plate and rain cover for the push button
• Remove the transparent paper from the name plate
position on the push button.
• Then write your name or room number on a small paper
(size:3.4cm/1.3in x 1.4cm/0.5in). Next, put the small paper
into the name plate position and then put back the
transparent paper.
• Install the rain cover onto the push button.
Note:
If you make the name plate by hand, be sure to use a
waterproof pen.
05 06

Disposal of the appliance
Under no circumstances should you dispose of the
appliance in normal domestic waste.This product is
subject to the provisions of European Directive
2012/19/EU.
The appliance’s packaging is made from environmen-
tally friendly material and can be disposed of at your
local recycling plant.
Dispose of the appliance via an approved disposal company or your
municipal waste facility. Please observe the currently applicable
regulations. Please contact your waste disposal centre if you need
any further information.
Disposal
Disposal of batteries
Used batteries may not be disposed of in household
waste.
All consumers are statutorily required to dispose of batteries at a
collection point provided by their local municipality or retail store.
The purpose of this obligation is to ensure batteries are disposed of
in a non-polluting manner. Only dispose of batteries when they are
fully discharged.
07 08