2gig Technologies Touch Screen Wireless Keypad User manual

INSTALL INSTRUCTIONS
Thisdocumentdescribesthebasicinstallationinformationforthe2GIG‐
TS1andthestepsnecessaryto“pair”(orlearnin)theTouchscreen
WirelessKeypadtotheControlPanel.
Box Contents
•2GIG‐TS1
•ACPowerSupply
•ACPowerSupplyBracket
•Screwsandanchors
TIP: TheboxcontentswillvarydependingonwhethertheTS1was
purchasedaspartofakitornot.
BEFORE YOU BEGIN
Is the 900 MHz Transceiver installed in the Panel?
FortheTS1tocommunicatewiththeControlPanel,the900MHz
Transceiver(2GIG‐XCVR2)mustbealreadybeinstalledintheControl
Panel.
Does the TS1 firmware version match the Control
Panel firmware version?
TheTS1andtheControlPanelarerequiredtohavethesamefirmware
versiontofullycommunicatewitheachother(e.g.CPv1.10andTS1
v1.10).
To check for matching firmware versions
1FromboththeTS1andControlPanelHomeScreen,chooseSecurity
/Menu/Toolbox.
2FromtheToo lboxScreen,usethe→arrowunlyouseetheVersion
Screen.
TS1 Version Screen
Control Panel Version Screen
TS1 PRODUCT OVERVIEW
TheModel2GIG‐TS1Touch ScreenWirelessKeypadisaremotecontrol
devicethatoffersthefunctionalityofasystemkeypadbutalsoextends
allusercontrolofthe2GIGControlpaneltootherlocationsinauser’s
home.UsingtheTS1,userscancontrollights,thermostatanddoorlocks
andseethestatusofeveryzoneintheirhomeusingtheexactsameand
familiarinterfacefoundontheControlPanel.Thekeypadisdesignedfor
indooruseonly.
IMPORTANT: NotforUL985installations.
Thepanelandbuttonsserveascontrolsaswellasindicators.
Pressingthe(Emergency)buttondisplaysemergencyiconsonthe
displayforPanic,Fire,andEmergencyalarmactivation(eachhas
programmableoptionsandcanbeenabledordisabled).Pressingthe
(Home)buttonchangesthesystemdisplaytotheHomeScreen.The
keypadispoweredfromaplug‐inpowersupply.The2GIG‐TS1exchanges
informationthroughasecure2‐waywirelessconnectionwiththeControl
Panel.
NOTE: BeforeusingtheTS1itmustbe“learned”intotheControl
Panel.
Mounting Tools
SomespecialtoolsmayberequiredtomounttheTS1ontothewall:
•Screwdriver
•Pencil
•Wirestripper
•Staplegun
•Drywallsaw(orequivalent)
• Ladder
PREPARING THE KEYPAD
NOTE: CheckthattheTS1Keypadisfunctioningbeforeselectinga
locationfortheKeypad.
1Remove the screw.
2Flip open the back cover of the TS1.
3Disconnect the hanging strap.
4Use the back cover as the mounting plate.
2GI
Touch Screen Wireless Keypad
ForRemoteControlofthe2GIGSecuritySystem

2©2013 2GIG Technologies Inc. All Rights Reserved.
SELECTING A LOCATION FOR THE KEYPAD
1MakesurethatACPowerisavailablenearby.
TIP: Becarefulofstuds,electricalwiresandpipesinthewall.
2Usethekeypad’sbackcoverasatemplatetomarkthescrewholes
withapencilandthepower(wiring)accesshole.
3Useadrywallsawtocutthewiringhole.
Mounting the Keypad
1Usethe3screwsandanchorsthataresuppliedtoattachthe
mountingplatetothewall.
2Route18AWGwirebetweenthekeypadandthelocationofthe
powersupply.
Wire Size and Length
Toensureproperoperation,DoNotexceedthefollowingmaximum
lengthforthewiresizeinstalled:
Toensurethattheappropriatewiresizeandlengthareinstalled,
measurethevoltagebetweenthepowerconnectionterminalsatthe
backofthecontrolpanel.Thevoltagemeasuredmustnotfallbelow11
voltsDCornuisance“ACPowerLoss”messagesmaybedisplayedand
reported.
NOTE: IntheUnitedStates,wiringroutedinsidewalls,ceilings,and
floorsmustcomplywithrequirementsoftheNationalElectrical
Code,ANSI/NFPA70andlocalbuildingcodes.Forwiringfrom
theoutputofthe2GIGclassIIpowersupply,wiringratedCL2,
CL2X,CL2R,orPLTCisrecommendedtosatisfythese
requirements.Ifthiswiringisinstalledinanairplenum(space
usedforenvironmentalairexchange)itmustberatedCL2P
(plenumrated).
Connect the Power Wires to the Keypad
1Re‐connectthehangingstrap.
2Use#6insulatedspadeterminals(notsupplied)toconnectwires
fromthepowersupplytothekeypad.
3Closethekeypad.
4Connectthepowerwirestothepowersupply.
Wire Size Maximum Length
22AWG 55feet(16.8meters)
20AWG 85feet(25.9meters
22AWG2‐pairs
(19AWGequivalent)
110feet(33.5meters)
18AWG 135feet(41.1meters)
ASnap case closed.
BTighten case screw.
ALeft Terminal 14 VDC(+)
BRight Terminal 14 VDC (-)
C18 AWG/2-Conductor

©2013 2GIG Technologies Inc. All Rights Reserved. 3
LEARNING/PAIRING THE KEYPAD WITH THE
CONTROL PANEL
1MakesurethattheControlPanelhaspowerusingthesuppliedAC
adapterandconfirmthattheadapterisconnected.
WARNING: AControlPanelwithoutthe900MHzTransceiver
installedcannotcommunicatewiththeTS1.
2MakesurethattheTS1haspowerfromthesuppliedACtransformer.
ConnecttheACadaptertotheTS1.Confirmthatthewiresare
connectedusingthecorrectpolarity.
3AstheTS1powersup,thefollowingmessageisvisibleonthedisplay.
4FromtheControlPanel’sInstallerToolbox,selectSystem
Configuration.
5SelecttheGoTobutton.
6Togotoquestion4,enter04.
7SelecttheRFKeypadnumbertoassigntotheTS1.Usethe→arrow
toselecttheRFKeypadnumber(1‐4).AfterselectingtheRFKeypad
number,pressthe↓arrowtostartconfiguringthespecific
parametersfortheRFKeypad.
8Pressthe→arroworpressthenumber1onthekeypadtogglethe
sengonthefirstquesonto“used”.Pressthe↓arrowtoconnue
configuringoptions.
9SettheRFKeypadEquipmentCodeto1059bypressingthe↓arrow
until“(1059)2GIG‐TS1wirelesstouchscreenkeypad”appears.Press
the↓arrowtoadvancetothenextopon.
10 LearntheTS1intotheControlPanel.Aerpressingthe↓arrowin
thepreviousstep,theLearnbuttonappears.
INITIATING THE PAIRING PROCESS
InitiatethepairingprocessattheControlPanelbypressingtheLearn
button.
1OntheControlPanelpresstheLearnbutton.

4©2013 2GIG Technologies Inc. All Rights Reserved.
2OntheTS1pressthePairwithPanelbutton.
TheControlPaneldisplaysthemessage:
PairwithTS1.Initiatinglearningprocess.
Whenlearningiscomplete,boththeTS1andControlPaneldisplay
themessage:
Thelearnoperationsucceeded.
2a TheControlPaneldisplaysthemessage:
Type:TS1WirelessKeypadID#:X
(whereXistheRFKeypadnumberconfiguredfortheTS1).
2b TheTS1displays“NetworkID:xxxx”wherexxxxisaunique
hexadecimalnumberandakeypadID.Thehexadecimalnumber
isauniquenumberassociatedwiththeControlPanelthatyou
areusing.ThekeypadIDindicatesthekeypadthatyouare
learningintotheControlPanel.
2c Tocompletethelearningprocess,presstheOKbuttononboth
theControlPanelandtheTS1.
3AftersuccessfullylearningtheTS1intotheControlPanel,pressthe
↓arrowtoexitthelearningmenu.
TheTS1displaysamessageindicatingthatthesecuritysystemis
temporarilyinoperable.TheTS1remainsinthisstatewhilethe
ControlPanelisinsystemconfiguration(programming)mode.
RepeatthestepsabovetolearninadditionalTS1s.
4Toexitprogramming,clickskipthenendandexit.Uponexit,the
ControlPaneltakesaseveralsecondstoreboot.
REMOVING A TS1 FROM A CONTROL PANEL
(UNLEARNING THE TS1)
ToremoveaTS1fromaControlPanel’sconfigurationdothefollowing:
1FromtheControlPanel,gotoInstallerToolbox/System
Configuration.
2SelecttheGoTobuttonandenter04.TheControlPaneldisplays
Q4:selectRFkeypad#(1to4).SelecttheconfiguredTS1youwishto
removeandpressthe↓arrow.
3MarktheRFKeypadnumberselectedas“unused”bypressingthe→
arrow.Thisactiontogglesthesettingonthefirstquestionbetween
“used”and“unused.”Pressthe↓arrowtoadvancetothenext
option.
4Toexitprogramming,clickskipthenendandexit.Uponexit,the
paneltakesseveralsecondstoreboot.
RESETTING A TS1 TO FACTORY DEFAULTS
ToresettheTS1todefaultssothatitmaybeusedagainonanother
ControlPanel,dothefollowing:
1Holdboththe(Emergency)andthe(Home)buttonsdown
simultaneouslyuntiltheylightup(approximately20seconds).When
bothbuttonslightup,theTS1hassuccessfullybeenresettoall
defaultsettings.
TheTS1displaysthemessage:
ThisDeviceisNotPairedwithaControlPanel.
SECRET DURESS BUTTON
TIP: ThelogoonthebottomcorneroftheHomeScreendoesnot
accesstheInstallerToolboxontheTS1.
IfauserpressesthelogoonthebottomcorneroftheTS1HomeScreen,
theusercanentertheduresscodeonly.Installersmustrememberthat
theInstallerToolboxcanonlybeaccessedfromtheControlPanel.The
TS1cannotaccesstheInstallerToolbox.
TIP: Althoughthereisadefaultmastercode:1111,thereisno
defaultduresscode.

©2013 2GIG Technologies Inc. All Rights Reserved. 5
REGULATORY INFORMATION
Wireless Product Notice
Radiocontrolsprovideareliablecommunicationslinkandfillan
importantneedinportablewirelesssignaling;however,therearesome
limitationswhichmustbeobserved.
•ForU.S.installationsonly:Theradiosarerequiredtocomplywith
FCCRulesandRegulationsasPart15devices.Assuch,theyhave
limitedtransmitterpowerandthereforelimitedrange
(approximately400ft.).
•Areceivercannotrespondtomorethanonetransmittedsignalata
timeandmaybeblockedbyradiosignalsthatoccuronorneartheir
operatingfrequencies,regardlessofcodesettings.
• ChangesormodificationstothedevicemayvoidFCCcompliance.
• Infrequentlyusedradiolinksshouldbetestedregularlytoprotect
againstundetectedinterferenceorfault.
•Ageneralknowledgeofradioanditsvagariesshouldbegainedprior
toactingasawholesaledistributorordealer,andthesefactsshould
becommunicatedtotheendusers.
FCC NOTICE
Thisequipmentgeneratesandusesradiofrequencyenergyandifnot
installedandusedproperly,thatis,instrictaccordancewiththe
manufacturer’sinstructions,maycauseinterferencetoradioand
televisionreception.Ithasbeentypetestedandfoundtocomplywith
thelimitsforaClassBcomputingdeviceinaccordancewithPart15of
FCCRules,whicharedesignedtoprovidereasonableprotectionagainst
suchinterferenceinaresidentialinstallation.However,thereisno
guaranteethatinterferencewillnotoccurinaparticularinstallation.If
thisequipmentdoescauseinterferencetoradioortelevisionreception,
whichcanbedeterminedbyturningtheequipmentoffandon,theuser
isencouragedtotrytocorrecttheinterferencebyoneormoreofthe
followingmeasures:
•RelocatetheConsoleawayfromtheTV/radioreceiver.
•Re‐orienttheTV/radioantenna.
•PlugtheConsoleintoadifferentwalloutletsothattheConsoleison
adifferentbranchcircuit.
•Ifnecessary,theusershouldconsultthedealeroranexperienced
radio/televisiontechnicianforadditionalsuggestions.
Industry Canada Notices
NOTICE:Theringerequivalencenumber(REN)assignedtoeachterminal
deviceprovidesanindicationofthemaximumnumberofterminals
allowedtobeconnectedtoatelephoneinterface.Theterminationonan
interfacemayconsistofanycombinationofdevicessubjectonlytothe
requirementthatthesumoftheringerequivalencenumbersofallthe
devicesdoesnotexceed5.
NOTICE:TheIndustryCanadalabelidentifiescertifiedequipment.This
certificationmeansthattheequipmentmeetscertain
telecommunicationsnetworkprotective,operationalandsafety
requirements.TheDepartmentdoesnotguaranteetheequipmentwill
operatetotheuser’ssatisfaction.
Beforeinstallingthisequipment,usersshouldensurethatitis
permissibletobeconnectedtothefacilitiesofthelocal
telecommunicationscompany.Theequipmentmustalsobeinstalled
usinganacceptablemethodofconnection.Thecustomershouldbe
awarethatcompliancewiththeaboveconditionsmaynotprevent
degradationofserviceinsomesituations.
Repairstocertifiedequipmentshouldbemadebyanauthorized
Canadianmaintenancefacilitydesignatedbythesupplier.Anyrepairsor
alterationsmadebytheusertothisequipment,orequipment
malfunctions,maygivethetelecommunicationscompanycauseto
requesttheusertodisconnecttheequipment.
Usersshouldensurefortheirownprotectionthattheelectricalground
connectionsofthepowerutility,telephonelinesandinternalmetallic
waterpipesystem,ifpresent,areconnectedtogether.Thisprecaution
maybeparticularlyimportantinruralareas.
WARNING: CAUTION:Usersshouldnotattempttomakesuch
connectionsthemselves,butshouldcontacttheappropriate
electricinspectionauthority,orelectrician,asappropriate.
Operating and Storage Temperature
TherecommendedstoragetemperatureforallTouc hScreensis‐10°Cto
60°C(14°Fto140°F).
ForoptimalTouchScreenuse,operationaltemperatureis0°Cto49°C
(32°Fto120°F).
LIMITED WARRANTY
This2GIGTechnologiesproductiswarrantedagainstdefectsinmaterial
andworkmanshipfor1year.Thiswarrantyextendsonlytowholesale
customerswhobuydirectfrom2GIGTechnologiesorthrough2GIG
Technologies’normaldistributionchannels.2GIGTechnologiesdoesnot
warrantthisproducttoconsumers.Consumersshouldinquirefromtheir
installingdealerastothenatureofthedealer’swarranty,ifany.
Therearenoobligationsorliabilitiesonthepartof2GIGTechnologies
forconsequentialdamagesarisingoutoforinconnectionwithuseor
performanceofthisproductorotherindirectdamageswithrespectto
lossofproperty,revenue,orprofit,orcostofremoval,installation,or
reinstallation.Allimpliedwarrantiesforfunctionality,arevalidonlyuntil
thewarrantyexpires.This2GIGTechnologiesWarrantyisinlieuofall
otherwarrantiesexpressedorimplied.
For technical support in the USA and Canada:
855‐2GIG‐TECH(855‐244‐4832)
Email:[email protected]
Internet:dealer.2gig.com
Visitwebsitefortechnicalsupporthoursofoperation
For technical support outside of the USA and Canada:
Contactyourregionaldistributor
Visitdealer.2gig.comforalistofdistributorsinyourregion.
PN77‐000090‐001Rev.A