3M SelfCheck System V Series User manual

SelfCheck™ System
V-Series, R-Series, and BCS
Owners Manual
3M Security Systems Division
3M Center, Building 225-4N-14
St. Paul, Minnesota 55144-1000
78-8129-2528-3 Rev 1

©2006 3M. All rights reserved.
3M is a trademark of 3M.
3M™ SelfCheck System V-Series, R-Series, and BCS Owners Manual
78-8129-2528-3 Rev 1

Table of Contents
Safety information ............................................................................................... 1
Intended use...............................................................................................................................1
Safety information for the V-Series Models 6410, 6420, and 7410 .......................................3
Safety information for the V-Series Tabletop Models 6412, 6422, 7412, and 7422.............4
Safety information for the R-Series Model 8410.....................................................................5
Safety information for the BCS Model 9410............................................................................6
V-Series label locations ............................................................................................................7
V-Series Tabletop Unit label locations....................................................................................8
R-Series label locations............................................................................................................9
BCS label locations .................................................................................................................10
Regulatory compliance...................................................................................... 11
EMC compliance USA and Canada........................................................................................11
Industry Canada radio frequency rules and regulations.....................................................11
EMC compliance Europe.........................................................................................................11
Australia....................................................................................................................................11
Japan.........................................................................................................................................11
Overview ............................................................................................................ 12
V-Series specifications ...........................................................................................................13
V-Series Tabletop Unit specifications...................................................................................14
R-Series specifications...........................................................................................................15
BCS Model 9410 specifications..............................................................................................16
Components.............................................................................................................................17
V-Series .....................................................................................................................................17
V-Series Tabletop Units.............................................................................................................17
R-Series.....................................................................................................................................18
BCS Model 9410........................................................................................................................18
Color touch-screen monitor .......................................................................................................19
Magnetic card reader.................................................................................................................19
Barcode scanner........................................................................................................................19
Smart card reader......................................................................................................................19
Receipt printer ...........................................................................................................................19
V-cradle......................................................................................................................................19
RFID reader pad ........................................................................................................................19
Interconnect box ........................................................................................................................20
V-coil driver box .........................................................................................................................20
Appliance coupler ......................................................................................................................20
Computer ...................................................................................................................................20
Communications......................................................................................................................21
Barcode formats ......................................................................................................................21
Touch screen monitor controls ......................................................................... 22

1
Safety information
Read, understand, and follow all safety information contained in these instruc-
tions prior to installation and use of the 3M™ SelfCheck™ System V-Series Model
6410, 6420, and 7410, the 3M SelfCheck System V-Series Tabletop Models 6412,
6422, 7412, and 7422, the 3M SelfCheck System R-Series Model 8410, and 3M
SelfCheck System BCS Model 9410. Retain these instructions for future reference.
Intended use
The 3M SelfCheck System V-Series Model 6410, 6420, and 7410, 3M SelfCheck System
V-Series Tabletop Models 6412, 6422, 7412, and 7422, 3M SelfCheck System R-Series
Model 8410, and 3M SelfCheck System BCS Model 9410 are intended for use by library
patrons in checking out books with minimal assistance by library staff. The V-Series and
R-Series models can be installed into a desk unit from 3M or into furniture provided by the
customer. The V-Series Tabletop Models 6412, 6422, 7412, and 7422 and the BCS Model
9410 is intended for use on a desktop provided by the customer.
These systems must be installed as specified in their respective site planning
guides and field service handbooks. They are intended for use in an indoor
library environment and have not been evaluated for other uses or locations.
EXPLANATION OF SIGNAL WORD CONSEQUENCES
!
DANGER: Indicates a potentially hazardous situation, which, if not avoided,
will result in death or serious injury and/or property damage.
!
WARNING: Indicates a potentially hazardous situation, which, if not avoided,
could result in death or serious injury and/or property damage.
!
CAUTION: Indicates a potentially hazardous situation, which, if not avoided,
may result in minor or moderate injury and/or property damage.
CAUTION: Indicates a potentially hazardous situation, which, if not avoided,
may result in property damage.

2
EXPLANATION OF PRODUCT SAFETY LABEL SYMBOLS
Attention: Read accompanying
documentation
High voltage.
Power must be
disconnected
before servicing.
Disconnect power before servicing. Unit
contains high voltage electrical circuits that
must be discharged and checked for voltage
prior to servicing. Service should be performed
only by 3M factory trained service personnel.
DANGER
Risk of electric shock
Display Unit: Mercury disposal
hazard
CAUTION
LASER LIGHT
DO NOT STARE INTO BEAM
0.95 mW at 630-670 nm
CLASS 2 LASER PRODUCT
Laser Scanner: Laser exposure

3
Safety information for the V-Series Models 6410, 6420, and 7410
!
WARNING
To reduce the risk associated with fire due to modification or incorrect
installation of system components or the use of non-approved replacement
components:
Do not attempt to modify or repair—no user serviceable parts—contact 3M
Service for repair.
Use approved system components installed by 3M service personnel only.
Install system components into desk or enclosure according to instructions and
specifications given in the appropriate site planning guide.
To reduce the risk associated with hazardous voltage due to a user attempting
to service a component, incorrect installation of system components, or use of
the system when damage has occurred:
Do not attempt to modify or repair—no user serviceable parts—contact 3M
Service for repair.
Install system components into desk or enclosure according to instructions and
specifications given in the appropriate site planning guide.
Do not use the V-cradle, coil driver box, interconnect box, appliance coupler, or
computer if any cases or power cords are damaged.
!
CAUTION
To reduce the risk associated with environmental contamination due to the
incorrect disposal of the lithium battery in the PC, mercury in the monitor/
display, and/or any circuitry that contains lead in the solder:
At the end of service life, dispose of the V-cradle, coil driver box, interconnect box,
appliance coupler, computer, monitor, and laser scanner in accordance with
federal, state, and local requirements.
To reduce the risk associated with exposure to laser light due to a person
looking into the laser scanner:
Do not look directly into laser scanner device;
At the end of service life, dispose of laser scanner in accordance with federal,
state, and local requirements.
IMPORTANT NOTE
The Code of Federal Regulations (CFR) 21CFR1040.10 requires the following
statement for products containing lasers:
Caution—use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous laser light exposure.

4
Safety information for the V-Series Tabletop Models 6412, 6422,
7412, and 7422
!
WARNING
To reduce the risk associated with fire due to a user or installer attempting to service the SelfCheck
unit:
•Do not attempt to modify or repair — no user serviceable parts — contact 3M Service for repair;
•Use approved replacement components, installed by 3M Service personnel only.
To reduce the risk associated with hazardous voltage due to a user or installer attempting to service
the SelfCheck unit or use of the system when damage has occurred to power cord:
•Do not attempt to modify or repair — no user serviceable parts — contact 3M Service for repair;
•Use approved replacement components, installed by 3M Service personnel only;
•Do not use the SelfCheck Tabletop unit if the power cord is damaged — contact 3M Service for
repair.
To reduce the risk associated with tipping over of the Selfcheck Tabletop unit due to placement on
an unsuitable desk or table:
•Insure that the furniture onto which the Selfcheck is placed is strong enough and provides a low slip
surface to safely hold the unit to prevent tipping or falling;
•Install SelfCheck in accordance with instructions and specifications given in the SelfCheck Tabletop
Site Planning Guide.
To reduce the risk associated with back strain due to the heavy weight of the system:
•Follow safe lifting procedures.
!
CAUTION
To reduce the risk associated with environmental contamination due to the incorrect disposal of the
lithium battery in PC or mercury in monitor/display:
•At the end of service life, dispose of Selfcheck unit and any accessories in accordance with federal,
state and local requirements.
To reduce the risk associated with exposure to laser light due to a person looking into the laser
scanner, or incorrect disposal of the laser scanner:
•Do not look directly into laser scanner device;
•At the end of service life, dispose of laser scanner in accordance with federal, state and local
requirements.
IMPORTANT NOTE
The Code of Federal Regulations (CFR) 21CFR1040.10 requires the following statement for
products containing lasers:
Caution—use of controls or adjustments or performance of procedures other than those specified
herein may result in hazardous laser light exposure.

5
Safety information for the R-Series Model 8410
!
WARNING
To reduce the risk associated with fire due to modification or incorrect
installation of system components or the use of non-approved replacement
components:
Do not attempt to modify or repair—no user serviceable parts—contact 3M Service
for repair.
Use approved system components installed by 3M service personnel only.
Install system components into desk or enclosure according to instructions and
specifications given in the Model 8410 Site Planning Guide.
To reduce the risk associated with hazardous voltage due to a user attempting
to service a component, incorrect installation of system components, or use of
the system when damage has occurred:
Do not attempt to modify or repair—no user serviceable parts—contact 3M
Service for repair.
Install system components into desk or enclosure according to instructions and
specifications given in the Model 8410 Site Planning Guide.
Do not use the interconnect box, appliance coupler, or computer if any cases or
power cords are damaged.
!
CAUTION
To reduce the risk associated with environmental contamination due to the
incorrect disposal of the lithium battery in PC, mercury in monitor/display,
and/or any circuitry that contains lead in the solder:
At the end of service life, dispose of interconnect box, appliance coupler, PC,
monitor, and laser scanner in accordance with federal, state and local
requirements.
To reduce the risk associated with exposure to laser light due to a person
looking into the laser scanner:
Do not look directly into laser scanner device.
At the end of service life, dispose of laser scanner in accordance with federal,
state, and local requirements.
IMPORTANT NOTE
The Code of Federal Regulations (CFR) 21CFR1040.10 requires the following
statement for products containing lasers:
Caution—use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous laser light exposure.

6
Safety information for the BCS Model 9410
!
WARNING
To reduce the risk associated with fire due to modification or incorrect
installation of system components or the use of non-approved replacement
components:
Do not attempt to modify or repair—no user serviceable parts—contact 3M Service
for repair.
Use approved system components installed by 3M service personnel only.
Install system components according to instructions and specifications given in the
Model 9410 Site Planning Guide.
To reduce the risk associated with hazardous voltage due to a user attempting
to service a component, incorrect installation of system components, or use of
the system when damage has occurred:
Do not attempt to modify or repair—no user serviceable parts—contact 3M
Service for repair.
Install system components according to instructions and specifications given in the
Model 9410 Site Planning Guide.
Do not use the computer or monitor if any enclosures or power cords are
damaged.
!
CAUTION
To reduce the risk associated with environmental contamination due to the
incorrect disposal of the lithium battery in PC, mercury in monitor/display,
and/or any circuitry that contains lead in the solder:
At the end of service life, dispose of the computer, monitor, printer, and laser
scanner in accordance with federal, state and local requirements.
To reduce the risk associated with exposure to laser light due to a person
looking into the laser scanner:
Do not look directly into laser scanner device.
At the end of service life, dispose of laser scanner in accordance with federal,
state, and local requirements.
IMPORTANT NOTE
The Code of Federal Regulations (CFR) 21CFR1040.10 requires the following
statement for products containing lasers:
Caution—use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous laser light exposure.

7
V-Series label locations
6400_UG_00
CAUTION
LASER LIGHT
DO NOT STARE INTO BEAM
0.95 mW at 630-670 nm
CLASS 2 LASER PRODUCT
21 CFR Subchapter J,
IEC 60825-1:1997
and EN 60825-1:1996
BACKLIGHT CONTAINS MERCURY,
DISPOSE ACCORDING TO LOCAL,
STATE, AND FEDERAL LAWS
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
This Class A digital apparatus also meets all requirements
of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les
exigences du Règlement sur le matériel brouilleur du Canada.
High voltage.
Power must be
disconnected
before servicing.
Disconnect power before servicing. Unit
contains high voltage electrical circuits that
must be discharged and checked for voltage
prior to servicing. Service should be performed
only by 3M factory trained service personnel.
DANGER
N1108
100 - 240V~
50/60 Hz
1 A
3
78-8126-7512-8
I.T.E. LISTED
ACCESSORY
4P24
N1108
100 - 240V~
50/60 Hz
12A MAX LOAD
3
78-8126-7519-3
N1108
100 - 125 / 220 - 240V~
60/50 Hz
2/1A
3
78-8126-7875-9
3M Library Systems
St. Paul, Minnesota 55144
I.T.E. LISTED
ACCESSORY
4P24
One of these labels
Model 6420 SelfCheck
100-120V~ / 200-240V~
60 / 50 Hz
3/1,5A
S/N: 642XXXX
3
3M Library Systems
St. Paul, Minnesota 55144
3M Library Systems
St. Paul, Minnesota 55144
I.T.E.
4P24
LISTED
N1108
Model 6410 SelfCheck
100-120V~ / 200-240V~
60 / 50 Hz
3 / 1,5 A
S/N: 641XXXX
3
3M Library Systems
St. Paul, Minnesota 55144
I.T.E.
LISTED
4P24
N1108
Model 7410 SelfCheck
100-120V~ / 200-240V~
60 / 50 Hz
3/1,5A
S/N: 741XXXX
3
3M Library Systems
St. Paul, Minnesota 55144
3M Library Systems
St. Paul, Minnesota 55144
N1108
FCC ID: DGFSSD7410
Canada: __________
I.T.E.
LISTED
4P24
Note: The barcode scanner uses a Class II laser. Up to 0.95 mW of laser power can be emitted onto objects.

8
V-Series Tabletop Unit label locations
High voltage.
Power must be
disconnected
before servicing.
Disconnect power before servicing. Unit
contains high voltage electrical circuits that
must be discharged and checked for voltage
prior to servicing.Service should be performed
only by 3M factory trained service personnel.
DANGER
N1108
100 - 240V~
50/60 Hz
1 A
3
78-8126-xxxx-x
N1108
100 - 125 / 220 - 240V~
60/50 Hz
2/1A
3
78-8126-xxxx-x
3M Library Systems
St. Paul, Minnesota 55144
I.T.E. LISTED
ACCESSORY
4P24
V-Series_OM_001
BACKLIGHT CONTAINS MERCURY,
DISPOSE ACCORDING TO LOCAL,
STATE, AND FEDERAL LAWS
One of these labels
Model 6412 SelfCheck
100-120V~ / 200-240V~
60 / 50 Hz
3 / 1,5 A
S/N: 641XXXX
3
3M Library Systems
St. Paul, Minnesota 55144
I.T.E.
LISTED
4P24
N1108
Model 6422 SelfCheck
100-120V~ / 200-240V~
60 / 50 Hz
3/1,5A
S/N: 642XXXX
3
3M Library Systems
St. Paul, Minnesota 55144
3M Library Systems
St. Paul, Minnesota 55144
I.T.E.
4P24
LISTED
N1108
Model 7412 SelfCheck
100-120V~ / 200-240V~
60 / 50 Hz
3/1,5A
S/N: 741XXXX
3
3M Library Systems
St. Paul, Minnesota 55144
3M Library Systems
St. Paul, Minnesota 55144
N1108
FCC ID: DGFSSD7422
Canada: __________
I.T.E.
LISTED
4P24
Model 7422 SelfCheck
100-120V~ / 200-240V~
60 / 50 Hz
3/1,5A
S/N: 741XXXX
3
3M Library Systems
St. Paul, Minnesota 55144
3M Library Systems
St. Paul, Minnesota 55144
N1108
FCC ID: DGFSSD7422
Canada: __________
I.T.E.
LISTED
4P24
CAUTION
LASER LIGHT
DO NOT STARE INTO BEAM
0.95 mW at 630-670 nm
CLASS 2 LASER PRODUCT
21 CFR Subchapter J,
IEC 60825-1:1997
and EN 60825-1:1996
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
This Class A digital apparatus also meets all requirements
of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les
exigences du Règlement sur le matériel brouilleur du Canada.

9
R-Series label locations
8400_UG_00
CAUTION
LASER LIGHT
DO NOT STARE INTO BEAM
0.95 mW at 630-670 nm
CLASS 2 LASER PRODUCT
21 CFR Subchapter J,
IEC 60825-1:1997
and EN 60825-1:1996
BACKLIGHT CONTAINS MERCURY,
DISPOSEACCORDING TO LOCAL,
STATE,AND FEDERALLAWS
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
This Class A digital apparatus also meets all requirements
of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe Arespecte toutes les
exigences du Règlement sur le matériel brouilleur du Canada.
N1108
100 - 240V~
50/60 Hz
1 A
3
78-8126-7512-8
I.T.E. LISTED
ACCESSORY
4P24
N1108
100 - 240V~
50/60 Hz
12A MAX LOAD
3
78-8126-7519-3
FCC ID: DGF-SSD8210
Canada: __________
3
Model 8410 SelfCheck ™
S/N: 841XXXX
Note: The barcode scanner uses a Class II laser. Up to 0.95 mW of laser power can be emitted onto objects.

10
BCS label locations
CAUTION
LASER LIGHT
DO NOT STARE INTO BEAM
0.95 mW at 630-670 nm
CLASS 2 LASER PRODUCT
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
This Class A digital apparatus also meets all requirements
of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les
exigences du Règlement sur le matériel brouilleur du Canada.
21 CFR Subchapter J,
IEC 60825-1:1997
and EN 60825-1:1996
Model 9410 SelfCheck
100-120V~ / 200-240V~
60 / 50 Hz
3/1,5A
S/N: 941XXXX
3
3M Library Systems
St. Paul, Minnesota 55144
3M Library Systems
St.
Paul, Minnesota 55144
I.T.E.
LISTED
4P24
N1108
9410_UG_00

11
Regulatory compliance
EMC compliance USA and Canada
FCC Radio Frequency Rules and Regulations
This equipment has been tested and found to comply with the limits for a
Class A device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can emit radiated radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference
at their own expense.
NO MODIFICATIONS. Modifications to this device shall not be made without
the written consent of The 3M Company. Unauthorized modifications may
void the authority granted under Federal Communications Commission Rules
permitting the operation of this device.
FCC Intentional Radiator Certification (Models 7410, 8410, 7412 and 7422 only)
Model 7410: FCC ID: DGFSSD7410
Model 8410: FCC ID: DGF-SSD8210
Model 7412 and Model 7422: FCC ID: DGFSSD7422
This equipment contains an intentional radiator approved by the FCC under
the FCC ID number shown above. This device complies with Part 15 of the
FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired
operation.
Industry Canada radio frequency rules and regulations
This Class A digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du
Règlement sur le matériel brouilleur du Canada.
EMC compliance Europe
This equipment complies with the requirements of the EMC directive.
Australia
This unit complies with the EMC requirements for Australia.
Japan
同梱の電源コードは当該製品専用です。

12
Overview
Welcome to the 3M™ SelfCheck™ System.
The SelfCheck system enables library customers to check library materials in
and out by themselves. The system emulates the check-in and checkout
procedures performed by library staff. In addition, the system can optionally
operate in offline mode when the library's automated circulation system is
unavailable.
Depending on the model, the SelfCheck system uses either a barcode
scanner or a radio frequency identification (RFID) reader to identify items
being checked into or out of the library. It also updates the library circulation
database and turns security attributes on or off as required.
This User Guide contains safety information, machine specifications,
commonly used procedures, and other information useful in the day-to-day
operations of library staff. It also contains administrator-level configuration
procedures.
Please take the time to read this guide. It will help you understand how your
SelfCheck system works. Keep it accessible when the system is in use. It will
serve as a reference guide when questions arise.

13
V-Series specifications
System physical characteristics (with cabinet)
Overall height 58.5 inches (148.6 cm)
Counter height 36 inches (91.4 cm)
Width 44.5 inches (112.9 cm)
Counter depth 26.5 inches (67.4 cm)
Base depth 34.5 inches (87.6 cm)
Weight
Laminate top
Corian® top
314 lbs. (142 kg)
334 lbs. (151 kg)
Shipping weight
Laminate top
Corian® top
364 lbs. (165 kg)
384 lbs. (174 kg)
System operating environment
Humidity 0% to 85% RH, non-condensing
Operating temperature 50° F to 93° F (10° C to 34° C)
Storage temperature −22° F to 131° F (−30° C to 55° C)
System power requirements
Voltage 100–120 VAC or 200–240 VAC
Current 6.0 A or 3.0 A
Frequency 50/60 Hz
Phase Single
Power 600 Watts
Component specifications
Component Dimensions Weight Electrical
Touch screen 16.1 in. × 10.2 in. × 15.7 in.
40.9 cm × 25.9 cm × 39.9 cm
16.3 lb
7.4 kg
12 VDC, 2.0 A
Scanner 2.59 in. × 1.38 in. × 3.47 in.
6.58 cm × 3.51 cm ×8.81 cm
7.5 oz
213 g
24 VDC, 300 mA
Printer 6.25 in. × 8.5 in. × 5.87 in.
15.9 cm × 21.6 cm × 14.9 cm
4.2 lb
1.9 kg
24 VDC, 3.0 A
Interconnect
box 12 in. ×12 in. ×3 in.
30.5 cm ×30.5 cm ×7.62 cm
3.6 lb
1.6 kg
100–240 VAC, 1.0 A
Coil driver box 11.5 in. ×10 in. ×4.8 in.
29.2 cm ×25.4 cm ×12.2 cm
15.0 lb
6.8 kg
100–240 VAC, 1.0 A
V-cradle 6.6 in. ×16 in. ×18.4 in.
16.8 cm ×40.6 cm ×46.7 cm
5.0 lb
2.3 kg
Powered by coil
driver box
Computer
without stand 13.3 in. × 3.95 in. × 15.1 in.
33.8 cm ×10.1 cm ×38.4 cm
22.2 lb
10.1 kg
Computer with
stand 14.3 in. × 7.0 in. × 15.1 in.
36.3 cm ×17.8 cm ×38.4 cm
23.2 lb
10.5 kg
120 VAC, 5 A or
240 VAC, 2.5 A

14
Component Dimensions Weight Electrical
Appliance
coupler 3.25 in. × 3.0 in. × 32.25 in. (max.)
8.26 cm ×7.62 cm ×81.9 cm
1.24 lb
0.56 kg
100–240 VAC, 12.0 A
V-Series Tabletop Unit specifications
System physical characteristics
Height 31.0 inches (78.7 cm)
Width 36.0 inches (91.4 cm)
Depth 30.5 inches (77.5 cm)
Weight
Laminate top
Corian® top
200 pounds (90.7 kg)
220 lbs. (99.8 kg)
Shipping weight
Laminate top
Corian® top
250 lbs. (113 kg)
270 lbs. (122 kg)
System operating environment
Humidity 0% to 85% RH, non-condensing
Operating temperature 50° F to 93° F (10° C to 34° C)
Storage temperature −22° F to 131° F (−30° C to 55° C)
System power requirements
Voltage 100–120 VAC or 200–240 VAC
Current 6.0 A or 3.0 A
Frequency 50/60 Hz
Phase Single
Power 600 Watts
Component specifications
Component Dimensions Weight Electrical
Touch screen 16.1 in. × 10.2 in. × 15.7 in.
40.9 cm × 25.9 cm × 39.9 cm
16.3 lb
7.4 kg
12 VDC, 2.0 A
Scanner 2.59 in. × 1.38 in. × 3.47 in.
6.58 cm × 3.51 cm ×8.81 cm
7.5 oz
213 g
24 VDC, 300 mA
Printer 6.25 in. × 8.5 in. × 5.87 in.
15.9 cm × 21.6 cm × 14.9 cm
4.2 lb
1.9 kg
24 VDC, 3.0 A
Interconnect
box 12 in. ×12 in. ×3 in.
30.5 cm ×30.5 cm ×7.62 cm
3.6 lb
1.6 kg
100–240 VAC, 1.0 A
Coil driver box 11.5 in. ×10 in. ×4.8 in.
29.2 cm ×25.4 cm ×12.2 cm
15.0 lb
6.8 kg
100–240 VAC, 1.0 A
V-cradle 6.6 in. ×16 in. ×18.4 in.
16.8 cm ×40.6 cm ×46.7 cm
5.0 lb
2.3 kg
Powered by coil
driver box
Computer xx.x in. × x.xx in. × xx.x in.
xx.x cm ×xx.x cm ×xx.x cm
xx.x lb
xx.x kg
120 VAC, 5 A or
240 VAC, 2.5 A

15
R-Series specifications
System physical characteristics (with cabinet)
Overall height 58.5 inches (148.6 cm)
Counter height 36 inches (91.4 cm)
Width 44.5 inches (112.9 cm)
Counter depth 26.5 inches (67.4 cm)
Base depth 34.5 inches (87.6 cm)
Weight
Laminate top
Corian® top
278 lbs. (126 kg)
298 lbs. (135 kg)
Shipping weight
Laminate top
Corian® top
328 lbs. (149 kg)
348 lbs. (158 kg)
System operating environment
Humidity 0% to 85% RH, non-condensing
Operating temperature 50° F to 93° F (10° C to 34° C)
Storage temperature −22° F to 131° F (−30° C to 55° C)
System power requirements
Voltage 100–120 VAC or 200–240 VAC
Current 6.0 A or 3.0 A
Frequency 50/60 Hz
Phase Single
Power 600 Watts

16
Component specifications
Component Dimensions Weight Electrical
Touch screen 16.1 in. × 10.2 in. × 15.7 in.
40.9 cm × 25.9 cm × 39.9 cm
16.3 lb
7.4 kg
12 VDC, 2.0 A
Scanner 2.59 in. × 1.38 in. × 3.47 in.
6.58 cm × 3.51 cm ×8.81 cm
7.5 oz
213 g
24 VDC, 300 mA
Printer 6.25 in. × 8.5 in. × 5.87 in.
15.9 cm × 21.6 cm × 14.9 cm
4.2 lb
1.9 kg
24 VDC, 3.0 A
Interconnect
box 12 in. ×12 in. ×3 in.
30.5 cm ×30.5 cm ×7.62 cm
3.6 lb
1.6 kg
100–240 VAC, 1.0 A
Computer
without stand 13.3 in. × 3.95 in. × 15.1 in.
33.8 cm ×10.1 cm ×38.4 cm
22.2 lb
10.1 kg
Computer with
stand 14.3 in. × 7.0 in. × 15.1 in.
36.3 cm ×17.8 cm ×38.4 cm
23.2 lb
10.5 kg
120 VAC, 5 A or
240 VAC, 2.5 A
Appliance
coupler 3.25 in. × 3.0 in. × 32.25 in. (max.)
8.26 cm ×7.62 cm ×81.9 cm
1.24 lb
0.56 kg
100–240 VAC, 12.0 A
BCS Model 9410 specifications
System operating environment
Humidity 0% to 85% RH, non-condensing
Operating temperature 50° F to 93° F (10° C to 34° C)
Storage temperature −22° F to 131° F (−30° C to 55° C)
System power requirements
Voltage 100–120 VAC or 200–240 VAC
Current 6.0 A or 3.0 A
Frequency 50/60 Hz
Phase Single
Power 600 Watts
Component specifications
Component Dimensions Weight Electrical
Touch screen 16.1 in. × 10.2 in. × 15.7 in.
40.9 cm × 25.9 cm × 39.9 cm
16.3 lb
7.4 kg
12 VDC, 2.0 A
Scanner 2.59 in. × 1.38 in. × 3.47 in.
6.58 cm × 3.51 cm ×8.81 cm
7.5 oz
213 g
24 VDC, 300 mA
Computer
without stand 13.3 in. × 3.95 in. × 15.1 in.
33.8 cm ×10.1 cm ×38.4 cm
22.2 lb
10.1 kg
Computer with
stand 14.3 in. × 7.0 in. × 15.1 in.
36.3 cm ×17.8 cm ×38.4 cm
23.2 lb
10.5 kg
120 VAC, 5 A or
240 VAC, 2.5 A