3M WallDisplay 8000PD Manual

Operator’s Guide
Guide de l’operateur
Benutzerhandbuch
Guida dell’operatore
Guía del operador
January 2005
78-6970-9184-7 Rev. C
Copyright © 2005, 3M.
All Rights Reserved.
8000PD
8000VC
…for video teleconferencing
…for projection

2
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Contents
English
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
System Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Remote Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Menu System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Français
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Installation du système . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Fonctionnement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Télécommande . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Système de menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Entrieten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Dépannage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Service après-vente . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Annexe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Deutsch
Einleitung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Enrichten des Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Bedienung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Fernbedienung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Menüsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Wartung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Fehlerbeseitigung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Serviceinformationen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Anhang . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Italiano
Introduzione . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Impostazione del sistema . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Funzionamento . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Telecomando . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Sistema di menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Manutenzione . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Risoluzioni dei problemi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Informazioni per l’assistenza . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Appendice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Español
Introducción . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Configuración del sistema . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Funcionamiento . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Unidad de control remoto . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Sistema de menús . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Mantenimiento . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Resolución de problemas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Información sobre servicio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Apéndice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
FRANÇAIS DEUTSCH ITALIANO ESPAÑOL

Operator’s Guide
October 2003
78-6970-9184-7 Rev. B
Copyright © 2003, 3M.
All Rights Reserved.
8000PD
8000VC
…for video teleconferencing
…for projection
©3M 2003. All Rights Reserved. 3

ENGLISH
(This page intentionally left blank for printed version)
©3M 2003. All Rights Reserved. 4

5
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Contents
Introduction
Thank You for Choosing 3M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Product Safety Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Save These Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Patents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
3M Digital WallDisplay Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
FCC Statement—Class A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
EEC Statement—Class A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Model Identification and Differences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
What’s Next? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Part Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
3M Digital WallDisplay Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
System Setup
Connecting to Various Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Operation
Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Remote Control Unit
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Forward Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Rear Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Installing or Replacing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Menu System
Menu Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Colorful—Bright Slider . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Warm—Cool Slider . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Volume Slider . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Mute Menu Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Input Select Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Reset All Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Image Adj Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Tools Sub-Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Maintenance
General Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

6
Contents 3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Lamp Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Onscreen Lamp Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Lamp Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Resetting Lamp Hours . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Replacing Projection Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Troubleshooting
Common Problems and Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Onscreen Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Service Information
Parts and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Ordering Parts or Getting Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Appendix
3M Digital WallDisplay Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Input/Output Signal Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Computer Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

7
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Introduction
Thank You for Choosing 3M
Thank you for choosing 3M equipment. This product has been produced in accordance with 3M’s highest quality
and safety standards to ensure smooth and troublefree use in the years to come.
For optimum performance, please follow the operating instructions carefully. We hope you will enjoy using this
high performance product in your meetings, presentations, and training sessions.
Intended Use
Before operating this machine, please read the entire manual thoroughly. The 3M Digital WallDisplay Systems
are designed, built, and tested for use indoors, using 3M lamps, 3M mount hardware, and nominal local voltages.
The use of other replacement lamps, outdoor operation, or different voltages has not been tested and could dam-
age the projector or peripheral equipment and/or create a potentially unsafe operating condition.
3M Digital WallDisplay Systems are designed to operate in a normal office environment.
• 16° to 29° C (60° to 85° F)
• 10 to 80% RH (without condensation)
• 0 to 1828 m (0 to 6,000 feet) above sea level
The ambient operating environment should be free of airborne smoke, grease, oil and other contaminants that can
affect the operation or performance of the 3M Digital WallDisplay.
Use of this product in adverse conditions will void the product warranty.
Safety Precautions
Read and understand all instructions before using. Pay particular attention to areas where this symbol is
shown:
Note: Emphasizes important conditions or details.
•Close supervision is necessary when any appliance is used by or near children. Do not leave
appliance unattended while in use.
•Never look directly into the projector lens when the lamp is on. The short-arc mercury lamp produces
a strong light that could damage your eyesight.
•Care must be taken, as burns can occur from touching hot parts when replacing the lamp.
•Do not operate appliance with a damaged cord or if the appliance has been dropped or
damaged, until it has been examined by a qualified service technician.
•Position the cord so that it will not be tripped over, pulled or placed in contact with hot
surfaces.
•If an extension cord is necessary, a cord with a current rating at least equal to that of the
appliance should be used. Cords rated for less amperage than the appliance may overheat.
WARNING Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation which, if not
avoided, could result in minor or moderate injury. It may
also be used to alert against unsafe practices.

8
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Introduction
Safety Precautions
•Always unplug appliance from electrical outlet before cleaning and servicing and when not in use.
Grasp plug and pull to disconnect.
•To reduce the risk of electric shock, do not immerse this appliance in water or other liquids.
•To reduce the risk of electric shock, do not disassemble this appliance. Request a qualified technician
when service or repair work is required. Incorrect reassembly can cause electric shock when the appli-
ance is subsequently used.
•Connect this appliance to a grounded outlet.
•Keep all ventilation openings free of any obstructions.
•The projection lamp contains mercury. Always dispose of this lamp in a proper manner according to
local regulations.
•Do not apply force to the projection arm. This may cause permanent damage to the unit or may cause
personal injury.
•Do not manually open or close the projection arm while the 3M Digital WallDisplay is in operation.
•The 3M Digital WallDisplay’s projection arm is motorized, and extends 42˝ (106 cm) from the
installation while in use. Caution should be taken when operating or walking near the 3M Digital
WallDisplay. It is possible a tall person’s head or an upraised hand could come in contact with the pro-
jection arm.
•Do not place the product in direct sunlight, near heaters or heat radiating appliances.

9
Introduction
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Product Safety Label
The following safety label is used on or within the 3M Digital WallDisplay to alert you to this area requiring
your attention.
Save These Instructions
The information contained in this manual will help you operate and maintain your 3M Digital WallDisplay.
Wall Display
from3 M
CAUTION
In some countries, the voltage is NOT stable. This appliance is designed
to operate within a range of 100~240 volts, ±10 volts, but it could fail if
power drops or surges of ±10 volts occur. In these high-risk areas, it is
recommended to install a power stabilizer unit.

Introduction
10
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Trademarks
The 3M logo and 3M are registered trademarks of 3M Company. Vikuiti is a trademark of 3M Company.
Microsoft, Windows, Windows NT, Word, Excel, PowerPoint, Internet Explorer, and NetMeeting are either reg-
istered trademarks or trademarks of the Microsoft Corporation in the United States and/or other countries.
IBM is a registered trademark of International Business Machines Corporation.
Apple Macintosh and Apple PowerBook are registered trademarks of Apple Computer, Inc., registered in the
U.S. and other countries.
Intel and Pentium are registered trademarks of Intel Corporation or its subsidiaries in the U.S. and other coun-
tries.
Digital Light Processing is a trademark or registered trademark of Texas Instruments.
eBeam, e-Beam, eBeam Mouse, eBeam Moderator, eBeam Software, ImagePort and eBeam Presenter are regis-
tered trademarks of Electronics for Imaging, Inc.
Sun and Java are trademarks or registered trademarks of Sun Microsystems, Inc. in the United States and other
countries.
UNIX is a registered trademark in the United States and other countries, licensed exclusively through X/Open
Company Limited.
Palm is a trademark of Palm Computing, Inc. or its subsidiaries.
Netscape and the Netscape N and Ship’s Wheel logos are registered trademarks of Netscape Communications
Corporation in the U.S. and other countries. Navigator and Communicator are also trademarks of Netscape
Communications Corporation and may be registered outside the U.S.
All other products are trademarks or registered trademarks of their respective companies.
Patents
3M Digital WallDisplay is protected by Utility Patent 6,179,426 and Design Patent D442,205.
Other patents pending.
3M Digital WallDisplay Technical Support
• In U.S. or Canada: 1-800-328-1371
• Web Site: http://www.3M.com/walldisplay

Introduction
11
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
FCC Statement—Class A
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received, includ-
ing interference that may cause undesired operation.
Instructions to Users
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide a reasonable protection against harmful
interference when the equipment is operated in a commercial environment. Thisequipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruc
tion manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
Notice
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.
EEC Statement—Class A
This machine was tested against the 89/336/EEC (European Economic Community) for EMC (Electro Magnetic
Compatibility) and fulfills these requirements.
Video Signal Cables
Double shielded coaxial cables (FCC shield cable) must be used, and the outer shield must be connected
to the ground. If normal coaxial cables are used, the cable must be enclosed in metal pipes or in a simi-
lar way to reduce the interference noise radiation.
Video Inputs
The input signal amplitude must not exceed the specified level.
(See Appendix for these levels.)
WARNING This is a Class A product. In a domestic environment, this
product may cause radio interference in which case the
user may be required to take adequate measures.

Introduction
12
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Model Identification and Differences
Identify Model
The nameplate, located behind the storage door, identifies the 3M Digital WallDisplay (DWD). Push the storage
door to open it. The figure below shows the nameplate, and the table shows the model numbers and correspon-
ding model names.
Model Number Model Name
8000DP 3M Digital WallDisplay 8000DP for Projection Display
8000VC 3M Digital WallDisplay 8000VC for Video Teleconferencing
8100CB 3M Digital WallDisplay 8100CB with Copyboard Display
8200IC 3M Digital WallDisplay 8200IC with Interactive Collaboration
8200IW 3M Digital WallDisplay 8200IW with Interactive Whiteboard
Model Differences
Below is a table that identifies the differences between the 3M Digital WallDisplay models.
Model Number Projection Screen Copyboard* Interactive Whiteboard**
8000DP Easy Dry-Erase and NO NO
Projection
8000VC 3M Vikuiti High Brightness NO NO
for projection only
8100CB Easy Dry-Erase and YES NO
Projection
8200IW Easy Dry-Erase and YES NO
Projection
8200IC Standard Projection YES YES
and Dry-Erase
*The Copyboard feature allows you to print notes written on the 3M Digital WallDisplay to an attached
printer. (PCL3 compatible printer required. See list in Appendix.)
** The Digital Whiteboard feature allows you to capture notes written on the 3M Digital WallDisplay with
an attached computer or use the 3M Digital WallDisplay as an interactive display for a computer.
CAUTION
Do not use markers, dry-erase or otherwise, on the 3M Digital WallDisplay
for Video Teleconferencing screen. Marks cannot be removed from the
3M Vikuiti High Brightness projection screen.
Model Number

Introduction
13
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Contents
The 3M Digital WallDisplay is shipped with the necessary cables required for standard VCR, PC, Macintosh or
laptop computer connections. Carefully unpack and verify that you have all of the items shown below. If any are
missing, please contact your place of purchase.
Optional Accessories
• Accessory Tray/Laptop Shelf • Easy-Erase Screen
• Replacement Lamp Kit • Extended Warranty
Note: Save the shipping box and packing materials in the event the 3M Digital WallDisplay should ever
need to be moved.
What’s Next?
After the 3M Digital WallDisplay has been installed in your meeting room, you are ready to set it up.
Please read this guide thoroughly before operating your new 3M Digital WallDisplay.
Be sure to check our web site (www.3M.com/walldisplay) regularly for updates and supplemental information.
POWER
R
MOUSE
MENU
INPUT
BLANK
MUTE
ON
OFF
1 2 3 4 5 6
3M™ Digital WallDisplay8000DP
...for ProjectionDisplay
3M™ Digital WallDisplay 8000VC
...for Video Teleconferencing
Remote Control
(with batteries)
Mac
adapter Power Cable
(US, UK, Euro)
Serial
Mouse Cable DVI-D Cable
3-Conductor
Video/Audio Cable
VGA Cable PC Audio
Cable
S-Video
Cable
USB
Cable
Operator’s Guide
(CD-ROM) Product Registration
Card

Introduction
14
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
PC
AUDIO
USB
MOUSE
SERIAL
MOUSE
RS-232AUDIO VIDEO COMPUTERROW
1
2 (THIS ROW FOR DIGITAL WHITEBOARD OPTION ONLY) PRINTER COMPUTER
S-VIDEO RCA VGA DVI-D
OUT IN
MENU KEYPAD
1
2
3
4
POWER R
MOUSE
MENU
INPUT
BLANK
MUTE
Wall Display
from3 M
Part Identification
1
3
5
11
2
4
12
67 8 9 10
13
14
15 16
17
18
19
1. Facade
2. Lamp Housing Door (behind facade)
3. Projection Screen
4. Left Bezel
5. Remote Control Unit
6. Storage Door
7. Storage Door Window
8. On/Off Button
9. Infrared Remote Sensor
10. Connection Panel Door
11. Right Bezel
12. Speakers
13. Projection Head
14. Projection Arm
15. Connection Panel
16. Menu Keypad
17. Status LED Indicators
18. Master Power Switch
19. AC Power Cord Socket

Introduction
15
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
3M Digital WallDisplay Features
The 3M Digital WallDisplay combines the following features into one sleek, sophisticated package.
• Full connectivity for computer or video presentations
•Large 60˝ diagonal screen
•4:3 screen aspect ratio matches business applications and viewing data
•Flat screen allows extra wide (up to 170°) viewing angles
•Projection arm position guarantees image is in focus every time
•Allows presenter to move without blocking image
•Built-in, powerful stereo speaker system
•Single button operation
•Hand-held remote control for most functions
•3M Vikuiti High Brightness screen for improved image quality (3M Digital WallDisplay 8000VC only)

16
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
System Setup
Connecting to Various Equipment
It only takes a few minutes to connect the 3M Digital WallDisplay to your computer, VCR, DVD player, video
conference unit, or other devices.
The connection panel is located underneath the bottom right corner of the 3M Digital WallDisplay, under the
Connection Panel Door. Press and release door to access connection panel.
Note: Use the enclosed cables to ensure image and audio quality. Substituting cables of lesser quality may
result in poor image quality or audio noise.
PC Audio Connects to the computer’s audio output and provides audio for VGA and DVI-D
(Digital Visual Interface - Digital only) inputs.
USB Mouse Connects to the computer’s USB port and provides wireless mouse control using the 3M
Digital WallDisplay remote control Disk Pad button.
Audio Out Connects to an external audio amplifier and provides audio from the active audio
source.
Audio In Connects to the audio output of a video device (e.g. VCR or DVD), and provides audio
for both S-Video and RCA video inputs.
S-Video Connects to an S-Video output signal.
RCA Video Connects to a composite video device.
DVI-D Connects to a computer that supports the DVI-D interface.
VGA Connects to the VGA or monitor Out port of a computer.
Serial Mouse Connects to a computer’s 9-pin serial port and provides wireless mouse control using
the 3M Digital WallDisplay remote control Disk Pad button.
RS-232 Connects to a control device’s serial port and provides control of the 3M Digital
WallDisplay using RS-232C protocol and the specified serial commands.
P C
AUD I O
U S B
M O U SE
SE
R I A L
M O U SE
R S - 232 AUD I O V I D E O C O M P U T E RR O W
1
2
( T H I S R O W F O R D I G I T A L W H I T E B O ARD O P T I O N O N L Y ) P R I N T E RC O M P U T E R
S - V I D E O RCA V G AD V I - D
O U T
I N
FRONT OF PANEL
BOTTOM OF PANEL
PC
Audio
USB
Mouse Serial
Mouse RS-232
Audio Video Computer
Out S-Video RCA VGADVI-D In

17
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Operation
Startup
1. Plug power cord into wall socket.
2. Flip on the Master Power Switch beneath the lower left corner of the 3M Digital WallDisplay, near the
3M label. This should stay on at all times. Now the 3M Digital WallDisplay is in standby mode. The large
oval On/Off Button will be backlit amber after several seconds.
3. Press the On/Off Button in the center of the lower front panel. The projection arm will extend outward
from its housing at the top of the 3M Digital WallDisplay unit. Do not block its movement.
4. When the projection arm is fully extended, the lamp will turn on automatically. It will reach full illumina-
tion in approximately 60 seconds. The On/Off Button should then be backlit green.
CAUTION
•The 3M Digital WallDisplay’s projection arm is motorized. Do not block its
movement or force it to move while the 3M Digital WallDisplay is in
operation.
•Do not look directly into the 3M Digital WallDisplay projection lens. The
light from the lens may cause damage to eyes.

Operation
18
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Shutdown
1. Press the On/Off Button on the bottom center panel of the 3M Digital WallDisplay unit.
2. The lamp will turn off and the projector arm will return to its housing. The On/Off Button will flash
red as the arm closes.
Note: There is a 30-second reset period before the On/Off Button will function again. During this
period, the On/Off Button will flash red.
The fan will continue to run for approximately five minutes to cool the unit.
Note: If the 3M Digital WallDisplay will not be moved or disconnected, leave the Master Power Switch on
for your convenience.
Do not turn off the Master Power Switch or unplug the power cord before pressing the On/Off
Button. After the On/Off Button is pressed, the fan continues for approximately five minutes to cool
the 3M Digital WallDisplay.

19
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Remote Control Unit
Features
The remote control sensor is on the front lower panel of the 3M Digital WallDisplay unit. The distance between
the sensor and remote control must be shorter than 4 meters (13 feet).
The remote control unit has two keypads. The Forward keypad is above the flip-top cover. The Rear keypad is
beneath the cover. The Trigger Button is underneath the front IR Sensor of the remote control unit and can be
pressed easily with the index finger.
POWER
R
MOUSE
MENU
INPUT
BLANK
MUTE
POINTER
FREEZE
REVEAL TIMER
VOLUME
+
IR SENSOR
Transmits infrared signals to 3M
Digital WallDisplay unit.
DISK PAD
Press to control the computer’s
mouse, navigate the menu
system, or control the Pointer or
Reveal functions.
RMOUSE
Press for right-mouse-button
function in mouse mode.
MENU
Press to display onscreen
menu system.
BLANK
Press to turn the screen-
blanking function on/off.
INPUT
Press to change source of
input.
VOLUME
Press to adjust the speaker
and Audio Out sound level.
TIMER
Press to turn on/off display of
countdown timer.
FREEZE
Press to turn the still-mode
function on/off.
REVEAL
Press to uncover part of the
screen from top to bottom or
from left to right.
LED
Indicates that remote control unit
is transmitting signal.
POWER
Press to turn 3M Digital
WallDisplay on/off.
MUTE
Press to turn the audio (speaker)
function on/off.
POINTER
Press to turn the pointing
function on/off.
FORWARD KEYPAD
REAR KEYPAD
TRIGGER BUTTON
Press for left-mouse
button functions.

Remote Control Unit
20
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Forward Keypad
Power
Press to turn the 3M Digital WallDisplay on/off. When power is turned on, the 3M Digital WallDisplay will
automatically extend the projection arm and ignite the lamp.
Mute
Press to temporarily turn off the sound. Press again or press the Volume + or -buttons to restore sound.
Disk Pad
Press to:
•control the computer’s mouse when using the Mouse function.
•select menu items and adjust values in the onscreen menu system.
•control the Pointer position while using the Pointer function.
•control the path of the Reveal function.
While using the onscreen menu system or Pointer function, the computer Mouse function is temporarily dis-
abled. To regain computer mouse control, turn off the current function or the onscreen menu system.
Note: The USB or serial mouse cable must be connected between the 3M Digital WallDisplay and the
computer when using Mouse mode.
R Mouse
Acts as the right-mouse button when the mouse function is active.
Menu
Press to display the onscreen menu system. Press again to conceal the onscreen menu system.
Blank
Press to make the screen go blank. Press again to return to normal display function.
Input
Press to change the source of input for 3M Digital WallDisplay. The Input button cycles between Computer,
DVI, Composite Video (RCA jacks), and S-Video.
POWER R
MOUSE
MENU
INPUT
BLANK
MUTE