A-Neuvideo ANI-0104POE-XT User manual

ANI-0104POE-XT
1x4 HDMI POE 1080/4K30 CAT6 Extender Splitter, IR Return,
w/ 4x Receivers 230 ft (70M) AUTO SETUP
A-NeuVideo.com
Frisco, Texas 75036
INSTRUCTION MANUAL

SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your
equipment. Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of re, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain,
water and excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean
dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they
are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and
plugs, convenience receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken
so that the means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper
AC voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold.
Do not use the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may
impede the normal ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used
in an extremely dusty or smoky environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all
servicing to qualied service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports rst, then remove the power cable; nally, disconnect the interconnecting
cables to other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship
the unit, use only the original factory packing.
19. Service Information Equipment should be serviced by qualied service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain.
D. The equipment does not appear to operate normally, or exhibits a marked change in performance.
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY
INSTRUCTIONS CONTAINED WITHIN THIS MANUAL.

ANEUVIDEO
1
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power
supply. Please keep the following in mind as you unpack and install this equipment:
• Always follow basic safety precautions to reduce the risk of re, electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain, moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow
for sufcient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and is believed to be accurate. We assume no responsibility for
any infringements of patents or other rights of third parties which may result from its use.
We assume no responsibility for any inaccuracies that may be contained in this document. We make no commitment to update
or to keep current the information contained in this document.
We reserve the right to make improvements to this document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means — electronic, mechanical, magnetic, optical, chemical,
manual, or otherwise — without the express written permission and consent.
© Copyright 2021. All Rights Reserved.
Version 1.2 MAY 2021
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be trademarks of the companies with which they are associated.

ANEUVIDEO
2
TABLE OF CONTENTS
INTRODUCTION & CONTENTS .......................................................................................................2
FEATURES........................................................................................................................................3
SPECIFICATIONS......................................................................................................................4
OPERATION CONTROLS & FUNCTIONS.......................................................................................5
IR PIN DEFINITION...........................................................................................................................7
EDID MODE.......................................................................................................................................8
CONNECTION DIAGRAM.................................................................................................................9
INTRODUCTION
This HDMI 1x4 Splitter can distribute (1) HDMI source signal to any (4) display devices. Supports
video resolution up to 4K@30Hz 4:4:4. It is designed with (1) HDMI input, (1) HDMI loop output
and (4) CAT outputs. The HDMI signal transmission distance can be extended up to 131 ft (40M)
at the resolution of 4K30Hz, or 230 ft (70M) at 1080P@60Hz via a single CAT6 cable. The product
supports one-way IR return and advanced EDID management. This product has a 3 year warranty.
PACKAGE CONTENTS
Before attempting to use this unit, please check the packaging and make sure the following items
are contained in the shipping carton:
• HDMI 1x4 Splitter
• (4) CAT Receiver
• IR Blaster Cable (1.5M)
• (4) IR Receiver Cable (1.5M)
• (2) Mounting Ear
• 12V/2.5A DC Locking Power Adapter
• (8) Machine Screw (KM3x4)
• User Manual
NOTES
For the best results, it is suggested you use pure copper and not copper clad aluminum and use
solid, riser rated cable and not stranded cable. Stranded cable has ~20% higher signal attenuation
than solid, so its runs need to be shorter.
Contiguous cable runs are preferred. The use of network punch down into patch panels and keystone
jacks adds attenuation and runs need to be shorter.
The use of EZ-45® connectors are not recommended as the cable extends outside the end of the
RJ45 connector and can act as an inductor of noise.

3
FEATURES
• HDMI 1.4 and HDCP 1.4 compliant
• Video resolution up to 4K@30Hz (4:4:4) 8-bit
• Support audio formats of LPCM 7.1CH, Dolby True HD, and DTS-HD Master Audio
• Extend the signal transmission distance up to 131 ft (40M) at the resolution of 4K30 or 230 ft (70M)
at 1080P@60Hz via a single CAT6 cable
• Supports (1) HDMI input, (1) HDMI loop output and (4) CAT outputs
• Advanced EDID management
• Supports one-way POC function (only from transmitter to receiver)
• Compact design for easy and exible installation