Aaeon AEC-6612 User manual

Embedded Controller AEC-6612
AEC-6612
Compact Embedded Controller
Intel
®Atom™ D510 1.66GHz Processor
Dual LAN, 2/6 USB2.0, 2/6 COM, 1 VGA
2 PCI-Express Mini Card
AEC-6612 Manual 1st Ed.
November 2010

Embedded Controller AEC-6612
i
Copyright Notice
This document is copyrighted, 2010. All rights are reserved. The
original manufacturer reserves the right to make improvements to
the products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated, or
transmitted in any form or by any means without the prior written
permission of the original manufacturer. Information provided in
this manual is intended to be accurate and reliable. However, the
original manufacturer assumes no responsibility for its use, or for
any infringements upon the rights of third parties that may result
from its use.
The material in this document is for product information only and is
subject to change without notice. While reasonable efforts have
been made in the preparation of this document to assure its
accuracy, AAEON assumes no liabilities resulting from errors or
omissions in this document, or from the use of the information
contained herein.
AAEON reserves the right to make changes in the product design
without notice to its users.

Embedded Controller AEC-6612
ii
Acknowledgments
All other products’ name or trademarks are properties of their
respective owners.
•Award is a trademark of Award Software International, Inc.
•CompactFlash™is a trademark of the Compact Flash
Association.
•Microsoft Windows®is a registered trademark of Microsoft
Corp.
•Intel®, Atom™ are trademarks of Intel Corporation.
•PC/AT, PS/2, and VGA are trademarks of International
Business Machines Corporation.
All other product names or trademarks are properties of their
respective owners.

Embedded Controller AEC-6612
iii
Packing List
Before you begin operating your PC, please make sure that the
following materials are enclosed:
z1 AEC-6612 Embedded Controller
z2 Wallmount Brackets
z1 Screw Package
z1 CD-ROM for manual (in PDF format) and drivers
If any of these items should be missing or damaged, please contact
your distributor or sales representative immediately.

Embedded Controller AEC-6612
iv
Safety & Warranty
1. Read these safety instructions carefully.
2. Keep this user's manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Do
not use liquid or spray detergents for cleaning. Use a damp cloth.
4. For pluggable equipment, the power outlet must be installed near
the equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a firm surface during installation. Dropping
it or letting it fall could cause damage.
7. The openings on the enclosure are for air convection. Protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before
connecting the equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not
place anything over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the
power source to avoid damage by transient over-voltage.
12. Never pour any liquid into an opening. This could cause fire or
electrical shock.
13. Never open the equipment. For safety reasons, only qualified
service personnel should open the equipment.
14. If any of the following situations arises, get the equipment
checked by service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.

Embedded Controller AEC-6612
v
d. The equipment does not work well, or you cannot get it
to work according to the user’s manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT INAN ENVIRONMENT
WHERE THE STORAGE TEMPERATURE IS BELOW -20°C
(-4°F) OR ABOVE 55°C (131°F). IT MAY DAMAGE THE
EQUIPMENT.
FCC
This device complies with Part 15 FCC Rules.
Operation is subject to the following two
conditions: (1) this device may not cause
harmful interference, and (2) this device must
accept any interference received including
interference that may cause undesired
operation.
Caution:
There is a danger of explosion if the battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the
manufacturer’s instructions and your local government’s recycling or
disposal directives.

Embedded Controller AEC-6612
vi
Below Table for China RoHS Requirements
产品中有毒有害物质或元素名称及含量
AAEON Boxer/ Industrial System
有毒有害物质或元素
部件名称 铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr(VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
印刷电路板
及其电子组件 ×○○○○○
外部信号
连接器及线材 ×○○○○○
外壳 ×○○○○○
中央处理器
与内存 ×○○○○○
硬盘 ×○○○○○
电源 ×○○○○○
O：表示该有毒有害物质在该部件所有均质材料中的含量均在
SJ/T 11363-2006 标准规定的限量要求以下。
X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出
SJ/T 11363-2006 标准规定的限量要求。
备注：
一、此产品所标示之环保使用期限，系指在一般正常使用状况下。
二、上述部件物质中央处理器、内存、硬盘、电源为选购品。

Embedded Controller AEC-6612
vii
Chapter 1 General Information
1.1 Introduction................................................................1-2
1.2 Features....................................................................1-3
1.3 Specifications............................................................1-4
Chapter 2 Hardware Installation
2.1 Dimension and I/O of AEC-6612...............................2-2
2.2 Location of Connectors and Jumpers of the Main Board
.........................................................................................2-3
2.3 List of Jumpers..........................................................2-5
2.4 List of Connectors .....................................................2-6
2.5 Hard Disk Drive Installation.......................................2-8
2.6 Memory Card Installation .......................................... 2-13
2.7 Wallmount Kit Installation..........................................2-16
2.8 DIN Rail Kit Installation .............................................2-17
Chapter 3 AMI BIOS Setup
3.1 System Test and Initialization. ..................................3-2
3.2 AMI BIOS Setup........................................................ 3-3
Chapter 4 Driver Installation
4.1 Installation.................................................................4-3
Appendix A Programming The Watchdog Timer
A.1 Programming ........................................................A-2
A.2 W83627DHG Watchdog Timer Initial Program ....A-7

Embedded Controller AEC-6612
Chapter 1 General Information 1- 1
General
Chapter
1
Information

Embedded Controller AEC-6612
Chapter 1 General Information 1- 2
1.1 Introduction
The newest Boxer series AEC-6612 has been introduced by
AAEON and it utilizes Intel®Atom™ processor. In this era of
information explosion, the advertising of consumer products will not
be confined to the family television, but will also spread to
high-traffic public areas, like department stores, the bus,
transportation station, the supermarket etc. The advertising
marketing industry will resort to every conceivable means to
transmit product information to consumers. System integrators will
need a multifunction device to satisfy commercial needs for such
public advertising.
The AEC-6612 is designed for indoor environments due to the
following reasons; first, the AEC-6612 offers low power
consumption system that while operating in ambient temperatures
ranging from -20° to 60°C. The MTBF (Mean Time Before Failure)
rating states that the AEC-6612 can operate up to 50,000 hours at
40°C ambient temperature, which indicates its careful and long-life
design.
The AEC-6612 is a standalone high performance controller
designed for long-life operation and with high reliability. It can
replace traditional methods and become the mainstream controller
for the multimedia entertainment market.

Embedded Controller AEC-6612
Chapter 1 General Information 1- 3
1.2 Features
zIntel®AtomTM D510 1.66 GHz Processor
zCOM x 2 (Optional x 6), USB x 2 (Optional x 6)
zRS-232 x 1 (Optional x 5)
zFanless Cooling System
zGigabit Ethernet x 2
zPCI-Express Mini Card x 2
zATX/ACPI Power Mode

Embedded Controller AEC-6612
Chapter 1 General Information 1- 4
1.3 Specifications
System
zCPU Intel®AtomTM D510 1.66 GHz
Processor
zMemory DDR2 400/533 SODIMM x 1, Max. 2
GB
zVGA VGA x 1
zKeyboard/Mouse Keyboard & Mouse by USB
zEthernet 10/100/1000Base-TX Ethernet, RJ-45
connector x 2
zHard Disk Storage 2.5” SATAHDD Bay x 1
zExpansion Mini Card Slot x 2
zLCD/CRT
Controller Integrated in Processor, shared system memory up to 384MB
zSolid Storage
Disk Type 2 CompactFlashTM slot x 1
zSerial Port RS-232/422/485 x 1, RS-232 x 1
(optional x 5)
zUSB USB 2.0 x 4
zSystem Control Power ON/OFF
zLED Indicator Power LED x 1, Hard disk active LED
x 1
zWatchdog Timer Generates a time-out system reset,
setting via software
zPower Supply DC power input 12V/ 9-30V (optional)
zOS Support WinCE 6.0, Windows®XP Embedded,
Windows®XP, Windows®7, Linux
Fedora

Embedded Controller AEC-6612
Chapter 1 General Information 1- 5
Mechanical and Environmental
zConstruction Aluminum Alloy Chassis
zColor Dark Gray
zMounting Wallmount
zDimension 7.8”(W) x 2.3”(H) x 4.3”(D)
(197 mm x 57.2 mm x 110 mm)
zNet Weight 2.73 lb (1.24 kg)
zGross Weight 4.31 lb (1.96 kg)
zOperating
Temperature No Airflow:
-4°F ~ 113°F (-20°C ~ 45°C) (CFD)
-4°F ~ 122°F (-20°C ~ 50°C) (HDD)
Ambient with Airflow:
-4°F ~ 122°F (-20°C ~ 50°C) (CFD)
-4°F ~ 140°F (-20°C ~ 60°C) (HDD)
zStorage
Temperature -4°F ~ 140°F (-20°C ~ 60°C)
zOperating
Humidity 10 ~ 95% @ 40°C, non-condensing
zVibration 5 g rms/ 5~500Hz/ random
operation –CFD
1 g rms/ 5~500Hz/ random
operation –HDD
zShock 50 G peak acceleration (11msec.
duration) –CFD
20 G peak acceleration (11msec.
duration) –HDD
zEMC CE/FCC Class A

Embedded Controller AEC-6612
Chapter 2 Hardware Installation 2-1
Hardware
Installation
Chapter
2

Embedded Controller AEC-6612
Chapter 2 Hardware Installation 2 - 2
2.1 Dimension and I/O of AEC-6612
SYS
HDD
DC IN
12V
USB LAN1 LAN2 COM1 VGA
COM2
510
COM3 COM4 COM5
COM6
USB
USB

Embedded Controller AEC-6612
Chapter 2 Hardware Installation 2 - 3
2.2 Connectors and Jumpers of The Main Board
Component Side

Embedded Controller AEC-6612
Solder Side
Chapter 2 Hardware Installation 2 - 4

Embedded Controller AEC-6612
Chapter 2 Hardware Installation 2 - 5
2.3 List of Jumpers
The board has a number of jumpers that allow you to configure your
system to suit your application.
The table below shows the function of each of the board's jumpers:
Label Function
JP1 Touch Screen 4/5/8-wire Mode Selection
JP2 AT/ATX Power Mode Selection
JP3 COM2 RI/+5/+12V Selection
JP4 Clear CMOS
JP5 LVDS Inverter/ Backlight Bias/PWM Mode Selection
JP6 LVDS Operating Voltage Selection
JP7 LVDS Inverter/ Backlight Voltage Selection

Embedded Controller AEC-6612
Chapter 2 Hardware Installation 2 - 6
2.4 List of Connectors
The board has a number of connectors that allow you to configure
your system to suit your application. The table below shows the
function of each board's connectors:
Label Function
CN1 CPU FAN
CN2 +5VSB Output w/ SMBus
CN3 External +5VSB Input
CN4 LPC Expansion I/F
CN5 SATA Port #1
CN6 SATA Port #2
CN7 External 5V Input (depend on power input
configuration)
CN8 External 12V Input (depend on power input
configuration)
CN9 Touch Screen Connector
CN10 +5V Output for SATA HDD using
CN11 Front Panel
CN13 COM Port #6
CN14 USB Port #7
CN15 COM Port #5
CN16 USB Port #6
CN17 USB Port #5
CN18 COM Port #4
CN19 USB Port #4

Embedded Controller AEC-6612
Chapter 2 Hardware Installation 2 - 7
CN20 USB Port #3
CN21 COM Port #3
CN22 COM Port #2
CN23 Audio Line In/Out and MIC Connector
CN24 RJ-45 Ethernet #2
CN25 RJ-45 Ethernet #1
CN26 Digital I/O
CN27 Parallel Port
CN28 LVDS Inverter/ Backlight Connector
CN29 18-bit LVDS Output
CN30 USB Port #1 and #2
CN31 PS/2 Keyboard & Mouse
CN32 COM Port #1
CN33 Analog CRT Display
CN34 SIM Card Socket
CFD1 Compact Flash Disk
PCIE1 Mini-Card Slot #1
PCIE2 Mini-Card Slot #2
DIMM1 DDR2 SODIMM Slot