Aalborg PSV-1 User manual
PREPARATION and OPERATION
Prior to connecting gas/liquid flow lines inspect all parts of the
piping system including ferrules and fittings for dust or other
contaminants. Be sure to observe the direction of flow as indi-
cated by the arrow on the front of the valve when connecting
the fluid flow system to be monitored.
Insert tubing into the compression fittings until the ends of the
properly sized tubing home flush against the shoulders of the
fittings. Compression fittings are to be tightened according to
the manufacturer's instructions to one and one quarter turns.
Avoid over tightening.
Once installed inline with the gas or liquid to be controlled,
apply a variable DC power source at the two solenoid wires to
proportionally open and close the solenoid valve (there is no
polarity). The valve is set to begin opening at approximately 5
VDC. They can also serve as "on off" valves (valves are not
guaranteed for absolute closure). Optional PSV-D DRIVER
MODULE is available when use of a 0 to 5 VDC or 4 to 20 mA
reference control signal is desired. Contact your distributor or
Aalborg7for more information.
SPECIFICATIONS
POWER INPUT: 0 to 30 VDC.
MAXIMUM CURRENT REQUIRED: 400 mA.
ELECTRICAL CONNECTION: Male spade connectors.
TYPE OF OPERATION: Normally closed (nc).
CONNECTIONS: 1/4 inch compression fittings,
optional 1/8 inch for sizes 1, 2, 3
and 3/8 inch.
DIMENSIONS: 3.55 inch (90.2mm) high x 3.25
inch (82.6mm) long (with fittings)
x 1.00 inch (25.4mm) deep.
WETTED MATERIALS: Types: 316 and 416 stainless steel,
VITON7O-rings; BUNA-N7, EPR or
KALREZ7O-rings are optional.
MAXIMUM PRESSURE: 1000 psig (6896 kPa).
MAXIMUM DIFFERENTIAL
PRESSURE:
50 psid (345 kPa).
MAXIMUM INTERNAL LEAK: 0.5% FS.
LEAK INTEGRITY: 1 X 10-9 scc / sec Helium.
FLUID TEMPERATURE: 14 FF to 122 FF (-10 FC to 50 FC).
MAXIMUM TEMPERATURE
(TYPICAL):
174 FF (79 FC) inside, 130 FF
(54 FC) outside surface at 24 VDC.
ENVIRONMENTAL (PER IEC 664): Installation level II; pollution
degree II.
MODEL
NUMBER
ORIFICE SIZE
Cv
*maximum flow
[ml / min]
[inch] [mm] Air Water
PSV-1 0.020 0.51 0.009 3500 125
PSV-2 0.040 1.02 0.033 13000 400
PSV-3 0.055 1.40 0.055 21500 700
PSV-4 0.063 1.60 0.068 25000 850
PSV-5 0.125 3.18 0.240 100000 2873
PROPORTIONATING SOLENOID VALVES
pressure drop
PSV Proportionating Solenoid Valves are uniquely designed
to respond to variable power inputs (0-30 VDC) to regulate
flow of liquids and/or gases proportionately. For added safety
PSV valves are normally closed (NC) when de-energized.
* based on 10 psig [690 mbar] differential pressure.
TRADEMARKS
Aalborg
7is a registered trademark of Aalborg Instruments Inc.
Buna
7is a registered trademark of DuPont Dow Elastometers.
Kalrez
7is a registered trademark of DuPont Dow Elastomers.
Viton
7is a registered trademark of Dupont Dow Elastometers L.L.C.
6-32 UNC (2)HOLES
0.156
3.250
0.500
1.000
3.851
1.177
FLOW
Ø 0.250
COMPRESSION
FITTING
0.938
1.250
1.000
0.688
0.156
0.500
4-40 SOCKET SCREW
SPIDER SPRING
STEM
SEAT-VITON INSERT
ORIFICE
O-RING
BLOCK
CORE
SPIRAL SPRING
COMPRESSION SPRING
O-RING
O-RING
ADJUST. SCREW
VALVE BODY
05-19-2006
GUARD ASSEMBLY
NUT
MAINTENANCE
The solenoid valve consists of 316 and
416 stainless steel, and VITON7(or
optional BUNA-N7, EPR or KALREZ7) O-
rings and seals. No regular maintenance
is required except for periodic cleaning.
Various corrosive gases or liquids may
demand more frequent replacement of O-
rings and seals inside the valve. Be sure
to use an elastomer material, appropriate
for your specific application. Contact your
distributor or Aalborg7for optional sealing
materials available.
Set the PSV for maximum flow, and
attempt to flush through in both directions
with a clean, filtered, and neutral gas such
as nitrogen. [Another option for fully open-
ing the valve is to remove the plastic cap
on top of the valve, and turn the set screw
counterclockwise until it stops]. If block-
age is not alleviated, return the unit to
your distributor or Aalborg7for servicing.
It is the users responsibility to determine
if the instrument is appropriate for their
OXYGEN application, and for specifying
O2 cleaning service if required. Aalborg7
is not liable for any damage or personal
injury, whatsoever, resulting from the use
of this instrument for oxygen.
If the valve is left in the active mode for
an extended period of time, it may
become warm or even hot to the touch.
Use care in avoiding direct contact with
the valve during operation.
To protect servicing personnel it is
mandatory that any instrument being
serviced is completely purged and
neutralized of toxic, bacteriologically
infected, corrosive or radioactive
contents.
Use of the PSV valve in a manner other
than that specified in this instruction
sheet, may impair the protection
provided by the equipment.
AALBORG INSTRUMENTS w20 CORPORATE DRIVE wORANGEBURG, NY 10962 wPHONE: 845.770.3000 wFAX: 845.770.3010
PSV
SOLENOID VALVE
Aalborg7reserves the right to change designs and dimensions at its sole discretion at any time without notice.
For certified dimensions please contact Aalborg7
.
TD 1293 Revision J
This manual suits for next models
4
Other Aalborg Control Unit manuals
