A&D HL-200i User manual

HL
HLHL
HL-
--
-iseries Digital Compact Scale
series Digital Compact Scaleseries Digital Compact Scale
series Digital Compact Scale
Operating Instructions
Operating InstructionsOperating Instructions
Operating Instructions
Cautions
CautionsCautions
Cautions
GAvoid installing the scale in direct sunlight.
GAvoid over / shock load that could cause damage to the scale.
GUse the scale under conditions of -10°C to 40°C, less than 85% R.H.
GThe weighing pan cannot be removed. Do not pull on up it.
GDo not mix the battery types. Replace all of the batteries at same time.
GIf the scale is not to be used for a long period of time, remove the all batteries.
GUse only the specified AC adapter for the scale (AC adapter is optional).
Specifications
SpecificationsSpecifications
Specifications
HL-200i200 x 0.1 g / 7.05 x 0.01 oz / 1000.0 x 0.5 ct / 5.335 x 0.005 tl
HL-2000i2000 x 1 g / 70.5 x 0.1 oz / 4 lb 6.6 oz x 0.1 oz / 53.35 x 0.05 tl
Power 4 x “AA” size batteries (monitor batteries included) or AC adapter
Battery life Approximately 1000 hours with alkaline cells at 20°C / 68°F
Pan size 130 mm / 5.1 in.
Dimensions 130 (W) x 192 (D) x 51 (H) mm / 5.1 (W) x 7.6 (D) x 2.0 (H) in
Keys and Symbols
ON:OFF key Turns the scale power on/off.
RE-ZERO key Sets the display to zero.
UNITS key Changes weighing units.
Symbol STABLE £Indicates when the reading is stable.
Symbol ZERO!Indicates when the scale zero is correct.
Installing batteries / Connecting the AC adapter
Installing batteries / Connecting the AC adapterInstalling batteries / Connecting the AC adapter
Installing batteries / Connecting the AC adapter
Installing / Replacing Batteries
Installing / Replacing BatteriesInstalling / Replacing Batteries
Installing / Replacing Batteries
Remove the battery cover and insert 4 batteries (AA size)
into the battery housing, especially take care of the
polarities. Attach the battery cover again.
AC adapter (optional)
AC adapter (optional)AC adapter (optional)
AC adapter (optional)
Peel off the seal on the battery cover to thread the
AC adapter wire through. Plug the AC adapter to
the AC adapter jack inside the battery housing.
Attach the battery cover again.
Peel off the seal here
Battery cover
AC adapter jac
k

Weighing procedures
Weighing proceduresWeighing procedures
Weighing procedures
1. Turn on / off the scale
1. Turn on / off the scale1. Turn on / off the scale
1. Turn on / off the scale
Press the
ON:OFF key to turn on the scale. The scale displays all segments for a few
seconds and then displays zero.
Press the
ON:OFF key again to turn the scale off.
2. Select the weighing unit
2. Select the weighing unit2. Select the weighing unit
2. Select the weighing unit
Press the
UNITS key to select a weighing unit from “g”, “oz”, ct (HL-200i only) , “lb-oz”
(HL-2000i only) or “tl”. Normally the scale displays “g”when is shipped from the factory.
To turn on with other units, turn the scale off. Press and hold the UNITS key, then press
the ON:OFF key. The scale will start with the next unit.
3. Weighing
3. Weighing3. Weighing
3. Weighing
Verify the reading is zero. If not, press the RE-ZERO key to zero the display.
If you use a container for weighing, place an empty container on the weighing pan and
press the RE-ZERO key to zero the display.
Place the objects to be weighed on the pan or in the container. When the reading
becomes stable, the STABLE indicator £is displayed.
Note
NoteNote
Note
Automatic power
Automatic powerAutomatic power
Automatic power-
--
-off funct
off functoff funct
off function
ionion
ion
If the scale is left ON and the STABLE indicator £is displayed, the automatic power-off
function turns the scale off after approximately 5 minutes.
To disable or enable this function, press the ON:OFF key while pressing the RE-ZERO
key. When the scale is turned on, XXX (XXX = 1.00 etc.) is displayed and this
function is disabled. If XXX is not displayed, then the function is enabled.
Error message
Error messageError message
Error message
a Overload. Remove the objects from the pan.
a Low battery. Replace the batteries with new ones.
Calibration
CalibrationCalibration
Calibration
For information about calibration, please visit the A&D website (http://www.aandd.co.jp/).
g oz ct tl goz lb-oz tl
H
L
-2000
i
H
L
-200
i
“tl”= Taiwan tael
3-23-14 Higashi-Ikebukuro, Toshima-ku, Tokyo 170-0013 JAPAN
Telephone: [81] (3) 5391-6132 Fax: [81] (3) 5391-6148
WM+PD4000944

HL-iseries Digital Compact Scale
Calibration Instructions
YWarm up the scale for more than 5 minutes. Refer to the instruction
manual for how to disable the automatic power-off function, if necessary.
1. Calibration weight
Calibrate the scale with calibration weights equivalent to capacity.
HL-200i: 200g ± 0.02g
HL-2000i: 2000g ± 0.2g
2. Calibration procedures
(1) Start with the scale turned off. Press the ON:OFF key while pressing
both the RE-ZERO key and UNITS key. Cal
CalCal
Cal will be displayed.
(2) Press the RE-ZERO key to calibrate zero. Cal0
Cal0Cal0
Cal0 will be displayed.
Make sure there is nothing on the weighing pan. Wait for the stable
indicator to be displayed and press the RE-ZERO key.
Calf
CalfCalf
Calf will be displayed in a few seconds.
(3) Place the calibration weight on the center of the weighing pan. Wait for
the stable indicator to be displayed and press the RE-ZERO key.
The display will show end
endend
end .
(4) Remove the calibration weight and the scale will automatically return to
the weighing mode.
(5) Place the calibration weight on the center of the weighing pan again
and check the calibration has been done correctly.
YIf you press the UNITS key at step (2), a 4 digit number will be
displayed. Press the UNITS key again to return to Cal
CalCal
Cal .
End of calibration instructions.
ENGLISH