Aastra 9116LP User manual

9116LP User Guide

Introduction ................................................................................................. 1
Emergency Service Feature ..............................................................................1
Unpacking your phone ......................................................................................1
Key Descriptions ...............................................................................................2
Basic Installation ......................................................................................... 4
Installation – Line Power PBX ...........................................................................6
Making and Answering Calls ..................................................................... 7
Making a call .....................................................................................................7
Answering a Call ...............................................................................................7
Using the Hold Key ...........................................................................................7
Making a Handsfree call ....................................................................................7
Muting a Handsfree call ....................................................................................8
Disable Handsfree Option .................................................................................8
Using Redial ......................................................................................................8
Call Waiting ID ..................................................................................................9
Changing the display language .........................................................................9
Setting the date and time ................................................................................10
Adjusting the Handset and Speaker volume ...................................................10
Adjusting the Ringer Volume ...........................................................................10
Adjusting the Display Contrast ........................................................................10
Set Indicator Light ...........................................................................................10
Directory .................................................................................................... 11
Saving numbers and names to the Directory ..............................................11
Entering Names ..............................................................................................11
Making a call from the Directory ......................................................................12
Finding items in the Directory ..........................................................................12
Deleting items from the Directory ...................................................................12
Callers List ................................................................................................. 13
Using the Callers List ......................................................................................13
Finding a Callers Record in the Callers List ....................................................13
Making a call from the Callers List ..................................................................13
Editing in the Callers List .................................................................................14
Memory keys ............................................................................................. 15
Saving numbers and names into memory keys ..............................................15
Viewing memory key contents ........................................................................15
Labeling the memory keys ..............................................................................16
Making calls from memory keys .....................................................................16
Deleting memory keys .....................................................................................16
Saving features in memory keys .....................................................................17
Saving a feature and light in memory keys .....................................................17
Advanced Features ................................................................................... 19
Clear Message Waiting ...................................................................................19
Set Area Code .................................................................................................19
Turning the Call timer on or off ........................................................................20
Display Icons and Messages ................................................................... 21
Icons in the Callers List ...................................................................................21
Display messages ...........................................................................................21
Troubleshooting ........................................................................................ 22

1
Introduction
Introduction
Congratulations....
. on the purchase of your 9116LP telephone.
This guide contains operating information for your 9116LP.
Emergency Service Feature
The Model 9116LP will provide most basic telephone service features in the event of a
power failure. However, the light indication for message waiting and feature light on/
off will not function during a power outage.
Unpacking your phone
Along with this user guide and the feature card, the following items are included with
your telephone.
The 9116LP is an advanced single-line telephone, that offers the following features:
• Line Powered capability
• Handsfree (speakerphone) option with
mute capabilities
• 80 name and number Callers List
• Personal Directory for 20 name and number
directory
• 15 speed dial positions for frequently called
numbers or feature access codes
• Last number redial
• Class and voltage message waiting indication
Telephone
Memory key card
and plastic lens
Handset
Telephone
line cord
Handset cord
Telephone stand
Regulatory sheetPower adaptor
Number card
and plastic lens
The power adaptor is 9V DC, 300mA - please see the regulatory sheet for safety instruc-
tions regarding the power adaptor and operation of the telephone.
Short
line cord

2
Introduction
Key Descriptions
Keys Key Description
Set Indicator
Light
Flashes when the telephone rings, or when a call is on hold; lights
up when a message is waiting or when a feature or extension is in
use. See
Set Indicator Light
on page 10 for more information.
8 Programma-
ble Keys
Stores a name and number or feature for easy access.
I Access a list of 8 options to customize the features of your tele-
phone.
Callers
Flash
Redial
Dial
Mute
Options
Directory
Delete
Shift
Save
Options Key
Adjustable Display
Navigational Keys
Handset
Volume Bar
Dial Pad
8 Memory Keys

3
Introduction
J
Stores up to 20 names and phone numbers. See
Directory
on
page 11 for more information.
SVW
allows you to move up or down in the Directory, Callers
List, and Options List. When you are editing entries on the display,
T moves cursor to the left when entering or editing names or num-
bers U allows you to insert a space between characters.
N Ends an active call. Goodbye exits an open list, such as the Direc-
tory, Options or Callers List. It will not hang up a call that is on
hold.
O
Places calls on or off hold. See
Using the Hold Key
on page 7 for
more information.
R Sets the handset and speaker volume while on call.
Q and
light indicators
Activates the speaker and microphone so you can listen and talk
without using the handset; also mutes the microphone so that your
caller cannot hear you (the light indicator will flash when the
microphone is muted). Will also mute the handset when speaker-
phone is disabled
A Accesses a list of the last 80 calls received. The list begins with the
newest call and ends with the oldest. The oldest call is automati-
cally deleted to make room for the new calls when the list becomes
full. See
Callers List
on page 13 for more information
B Use with the network features such as Call Waiting and Three Way
Calling (flash is also referred to as link).
C
Displays the last number dialed out on the telephone. See
Using
Redial
on page 8 for more information.
D Dials the displayed telephone number, automatically activates the
handsfree mode if the handset is not picked up.
K Use to store numbers and names in Directory, in memory keys and
to access and save Option feature settings.
L Removes entries in the Directory, Callers List or Redial List. Erases
memory key information.
HUse to access the eight two-touch memory positions.
MMemory keys store numbers, names and features. See Memory
keys on page 15.
Keys Key Description

4
Basic Installation
Basic Installation
The 9116LP can be powered from either a PBX line or from the power adaptor sup-
plied with this product. If using the power adaptor, use the following instructions to
install this telephone. For information on installation using PBX line power, see the
next section.
1. Connect the Handset 2.Connect the Cords
Attach one end of the coiled handset cord to
the handset and the other end to the handset
port on the back of the telephone.
Route the handset cord along the groove lead-
ing off the side of the telephone as shown in
the illustration.
Plug one end of the telephone cord into
on the back of the telephone and the other
end to the phone jack.
Connect the small end of the power adaptor
to the port on the back of the telephone,
and plug the other end into an electrical outlet.
3. Attach the Stand for Desk Mount
If you plan to mount the telephone on the wall, you do not need to attach the stand.
Lower the stand as shown below into the slots
on the back of the telephone.
Slide the stand in the direction shown below
until it clicks into the locked position.
1

5
Basic Installation
4. Attach the cords to the telephone stand 5. Mount the telephone on the wall
Route the cords along the groove on the
telephone stand as shown in the illustra-
tion.
It is recommended that you use a wall-mounting
plate which is available through your telephone
company or a local retailer. You will find it easier to
wall-mount the telephone if you purchase one short
20 cm (8”) telephone cord and use it in place of the
long telephone cord.
Coil the telephone cord(s) into the space provided
on the back of the telephone.
Line up the keys on the wall mounting plate with
the key holes on the back of the telephone.
Place the telephone onto the wall mounting plate,
and then push down to secure the telephone into
place.
6. Insert the number card on your
telephone
7. Insert the Memory key card on your telephone
Write your telephone number on the
number card.
Place the number card into the slot
underneath the handset cradle on the
on the telephone.
Gently bend the clear plastic lens and
place it on top of the number card in
the slot.
This card contains the feature names for the dedicated
keys and label identification spaces for the eight pro-
grammable memory keys.
Place the card into the memory key card slot on the tele-
phone.
Gently bend the clear plastic lens and place it on top of
the memory key card in the slot.
For more information on programming memory keys,
refer to Memory keys on page 15.
Options
Directory
Delete
Shift
Save

6
Basic Installation
Installation – Line Power PBX
For line power installation, use the same instructions above but without using the sup-
plied power adaptor. Then proceed as follows to activate the phone:
1. Lift the handset from the cradle – time and date is displayed on the screen
2. Press I.
3. Press Wonce. Screen displays PBX-LINE.
4. Press K. Display shows ON OFF.
5. Use Tor Uto change the selection.
6. Press K.
Note: Once line power PBX is activated On, it will activate the Battery Icon.
Important: Operation of the 9116LP in line power mode should be restricted to use
behind a PBX line card with no other extensions running off the same line.
Should more than one phone be in use on the same line card, it is recommended that
the 9116LP be set up using D/C power.
The DC adapter must be connected to the 9116LP if an extension phone is connected to
the same telephone line. This will ensure full functionality for the 9116LP (e.g.
extension in use)
To avoid potential electrical shock hazard to personnel or damage
to the telephone, use only the manufacturer-supplied equipment
and installation procedures. Specifically, use only 4 conductor
modular teledapt plug/cords with this product, and an AC trans-
former that is CSA/UL or CSA-NRTL/C approved Class 2 level
C, rated as follows:
For North American Markets AC voltage 110-120V Input:
120VAC, 60Hz, 10W and Output: 9V DC, 300mA.
Substitution of non-approved equipment will void the Aastra
Telecom Inc., warranty. For more information about installation
and safety concerns, call 1-800-574-1611.

7
Making and Answering Calls
Making and Answering Calls
Making a call
With your telephone you can make and answer calls using your handset or Q
for speakerphone capabilities.
Answering a Call
When you subscribe to the Caller ID service from your telephone company, Caller ID
information is sent from the telephone company to your 9116LP telephone between
the first and second ring. Therefore, if you want the telephone number of the incoming
call to appear on the display and in the Callers List, you must wait until the informa-
tion appears on the display before answering the telephone.
Using the Hold Key
Note: The 9116LP automatically releases a call on hold when a person on an exten-
sion telephone on the same line picks up the call. If you don’t hang up the
handset after you have put a call on hold and that call is picked up by someone
at another extension, the call is taken off hold but remains connected to your
telephone. If this happens, any background noise from your area will be heard
by the caller and the person at the other extension.
Making a Handsfree call
You don’t have to use the handset to use your telephone. Instead, you can use Handsfree
mode to place a call, or you can switch to Handsfree mode while a call is in progress.
To make a regular call:
7. Lift the handset or press Q.
8. Enter the number using the dial pad.
To answer a call:
1. Lift the handset or press Q.
To put a call on hold and take a call off hold:
1. Make or answer a call.
2. Press O.
The set indicator light will flash quickly to indicate there is a call on hold.
3. To retrieve the call, press Oor Q. If you don’t retrieve the call within 15
minutes, the call is automatically dropped.
To dial without picking up the handset: To switch to a Handsfree call:
1. Press Q.1. Lift the handset.
2. Enter the number using the dial pad. 2. Dial a number using the dial pad.
3. When the call is over, press N.3. When the call is answered, press
Q.
4. Hang up the handset.
5. When the call is over, press N.

8
Making and Answering Calls
Muting a handsfree call
You can turn off the microphone so that the caller can’t hear you but you can still hear
the caller. Muting a call only works when you are in Handsfree mode.
Disable Handsfree Option
In many "open concept" offices, speakerphone usage is not a practical alternative. For
such environments, the 9116LP can be programmed to disable the speakerphone. As
the telephone is shipped with the speakerphone enabled, use the following steps to
disable (or activate) the speakerphone.
Note: If the speakerphone is Disabled then the Pkey will mute the Handset
with the Flashing LED accordantly.
Using Redial
Pressing Cdisplays the last number dialed. When you press Cthe last
number you called appears on the screen.
To mute a handsfree call:
1. Press Q.
2. Without lifting the handset, make a call.
3. To turn off the microphone, press Q. You can hear your caller but your
caller cannot hear you. The light beside Qflashes.
4. To speak to your caller, press Qagain. Each time you press Q, you
turn the microphone on or off.
5. When the call is over, press N.
To disable (or to activate) the speakerphone
1. Using the instructions for Setting the date and time on page 10 , change the
date and time to 1/01 12:00AM and save.
2. Press I.
3. Press O.
4. Press •key within 4 seconds.
To make a call using Redial:
1. Press C. The display shows the last number you dialed.
2. Lift the handset or press either Dor Q.

9
Making and Answering Calls
Call Waiting ID†
The 9116LP is capable of displaying Caller ID information of a second incoming call
while you have a call in progress. When you are on a call and you hear the Call Wait-
ing tone, the Call Waiting information is displayed as shown below.
If you decide you want to speak to the new caller, simply press B. Your first call
will not be disconnected. You may switch between callers as often as you like by press-
ing B. When you press Band see a caller’s Identification information but
only hear a dial tone, it means that the caller has hung up. Your second call will be
stored in the Callers List even if it is not answered. For more information about stored
calls, see Callers List on page 13.
Changing the display language
For changing business requirements, you may wish to change the language of your
display messages and prompts. There are three language choices available for your
telephone (English, French and Spanish).
†You must subscribe to your telephone company for the Call Waiting with Calling ID service.
To change the display language:
1. Press I.
2. Press Vonce and Set Language appears on the display.
3. Press K. The language indicators E, F, S appear on the display for English,
French and Spanish. The current selection is indicated by the flashing letter.
4. Use Uor Tto change the selection.
5. Press K.
Incoming caller's information
(Caller One) is displayed.
CALLER ONE
555-1234
CALLER ONE
555-1234
When you hear the Call Waiting tone,
Caller Two's information is displayed.
CALLER ONE
555-1234
CALLER TWO
555-56 8

10
Making and Answering Calls
Setting the date and time
If you subscribe to the Caller ID service from your telephone company, the date and
time are set automatically after you receive your first incoming call. If you do not sub-
scribe, you must set the date and time manually.
To resume the automatic date and time setting (if the date and time has been set man-
ually), disconnect the power supply (or the line cord if the phone is PBX powered),
then re-connect it. After your first incoming call, the date and time are automatically
set if you subscribe to the Caller ID service from your telephone company.
Adjusting the Handset and Speaker volume
Press the left or right side of the volume bar Rto adjust the volume on the
handset or speaker. The speaker volume remains at the level selected until the next
time you change it.
Adjusting the Ringer Volume
The ringer volume is controlled by a three position switch on the back of the Model
9116LP. The ringer volume can be set to be off, low or high.
Adjusting the Display Contrast
The contrast on the display screen can be adjusted as required to compensate for light-
ing conditions.
Set Indicator Light
The set indicator light, located on the top right hand corner of the Model 9116LP,
flashes and illuminates to provide information as follows:
*You must subscribe to Voice Mail features from your telephone company for this feature to work.
To set the date and time:
1. Press I.
2. Press Wor Vuntil display indicates Set Time/Date.
3. Press K. Display shows time and date. Use Wand Vto adjust the flashing
time and date and TUto move to the next field. To change the AM/PM indi-
cator, adjust the time ahead by 12 hours.
4. Press K.
To adjust the display contrast:
1. Press I.
2. Press Wor Vuntil screen displays Set Contrast.
3. Press K. Display shows 123456. Use Tand Uto move the flashing line to
adjust the contrast to the desired level.
4. Press K.
Set indicator light is on. Extension phone is in use.
Set indicator light flashes very quickly. Incoming call.
Set indicator light flashes quickly. Line is on hold.
Set indicator light double flashes. Message Waiting*.

11
Directory
Directory
The 9116LP telephone directory can store the names and telephone numbers of up to
twenty of your business associates, clients, contacts and friends for easy dialing.
Each directory record is numbered and identified by the number appearing in the bot-
tom, right hand corner of the screen display. Names and numbers can be manually
entered into the Directory using the keypad or transferred into the Directory from the
screen display.
If all twenty directory records are used, the display will indicate DIRECTORY FULL.
(See Deleting items from the Directory on page 12).
Saving numbers and names to the Directory
Entering Names
You can program names to correspond with numbers you have entered into the Direc-
tory or a memory key. The following paragraphs explain how to enter letters using the
dial pad. Before you can use the dial pad to enter names, you must first save or edit a
number in the Directory or memory key.
To save or edit a number and name: To save from the display:
1. Press J. The screen displays
DIRECTORY IS EMPTY or XX ITEMS.
1. Ensure that a number is on the display
(for example from the Callers List).
2. Press K. The screen prompts you
to enter the phone number you wish
to save.
2. Press K. The display indicated
SAVE TO?.
3. Enter the number using the dial pad.
You can enter a maximum of 16 digits.
If you need to add a pause (for exam-
ple between a telephone number and
an access code) press Oand the
Pause icon will appear. To program a
number that uses Flash, press the
Bkey where required and the
Flash icon will appear.
3. Press Kagain. The screen shows
ENTER NUMBER.
4. Press K. The screen prompts you
to enter the name you wish to save.
Use the dialpad to enter a name. See
Entering Names on page 11.
4. Press Kagain. The screen indi-
cates ENTER NAME. If there is already
a name associated with the number
or you do not wish to have a name
with this directory entry, go to the
next step. Use the dialpad to enter
the name if required. See Entering
Names on page 11.
5. Press K. The display shows
SAVED:DIRECTORY.
5. Press K. The display shows
SAVED:DIRECTORY.
6. Press Nto exit the Directory. 6. Press Nto exit the Directory.

12
Directory
To program a name, find the dial pad key that has the first character of the name. Keep
watching the display as you press the key until that character appears on the display. Press a
different dial pad key for the next character. If the next character is on the same key, press U
to move to the next space or wait a few seconds and it will automatically advance to the next
space. To insert a space, press U. To backspace and erase a mistake, press Tand L.
For example, to enter the name RUTH press these keys:
‡‡‡, °°, U, °, ››.
If you wish to change a digit or letter after you have entered it, press Tto erase it.
⁄, - ‘ & ( )1 ¤A B C 2 ‹D E F 3
›G H I 4 fiJ K L 5 flM N O 6
‡P Q R S 7 °T U V 8 ·W XY Z
•o‚0£o
Making a call from the Directory
Note: To leave the Directory at any time, press N.
Finding items in the Directory
Deleting items from the Directory
To make a call from the Directory:
1. Press J.
2. Press Vor Wor use the dial pad to find the item you want to dial out.
3. Lift the handset or press either Qor D.
4. To end the call, press Nor hang up.
To find items in the Directory:
1. To see the Directory List heading, press J.
2. Use the Wand Vto look at each individual directory entry one at a time.
3. To leave the Directory at any time, press N.
To delete individual items:
1. Press J.
2. Press VWto find the item you want to delete.
3. Press Ltwice. Selected item is deleted.
4. Press Nto exit the Directory at any time.
To delete all items:
1. Press J.
2. Press L, the screen indicates DELETE ALL?
3. Press Lagain to confirm deletion of the entire Directory.
4. Press N.

13
Callers List
Callers List†
Using the Callers List
The 9116LP telephone stores up to 80 calls in the Callers List. Your telephone logs the
number (and name if available) of the caller, when they last called, and the number of
times they tried to reach you. When the Callers List is full, the oldest call records are
deleted to accommodate the information of new callers. See Display messages on
page 21 for a description of the display messages.
If the telephone number of the incoming call matches a number that you have pro-
grammed with a name in a memory key or the Directory, the Callers List shows the
name you have saved in the memory key or Directory, and the number.
Finding a Callers Record in the Callers List
Making a call from the Callers List
If you call a number from the Callers List and you don’t get connected, you may have
to edit the number (for example, the number may be long distance and you may have
to add “1”).
Tip: If you frequently have to remove area codes to return local calls, use the Area Codes
option to avoid this situation. See Set Area Code on page 19 for more information.
†You must subscribe to your telephone company for the Caller ID service.
To find items in the Callers List:
1. Press A. The display shows the number of items (Caller Records).
2. Press Wto view other caller records one at a time starting from the second
most recent caller. To view from the oldest caller record to the most recent press
V. The screen may display XX ITEMS but continue to press Wor Vto see
the oldest call records.
3. Press Nto leave the Callers list.
To dial a number in the Callers List:
1. Press A. The display shows the number of items (Caller Records).
2. Press Wor Vto find the caller record you wish to dial to.
3. Lift the handset or press either Qor D.
4. To end the call, press Nor hang up.

14
Callers List
Editing in the Callers List
Deleting from the Callers List
To edit a number in the Callers List:
1. Press A.
2. Press WV keys to find the Caller record you wish to edit.
3. Use the dial pad to add digits. Added digits will appear to the left of the cursor.
Press Lto erase a digit and all digits to the right of the cursor will move one
position to the left. To add a pause press O. To add a Flash feature to a num-
ber, press B.
4. To dial the edited number, immediately lift the handset or press Dor
Qas soon as editing of the number is complete.
5. To save the edited number in the Directory rather than dialing it, go to step 3 below.
To copy a number from the Callers List to the Directory or to a memory key:
1. Press A.
2. Press WV keys to find the Caller record you wish to copy.
3. Press K. Display shows SAVED TO?.
4. Press Jor the memory key (or Hplus a memory key) where you want
to store the number.
5. The screen indicates ENTER NUMBER.
6. Press Kagain. If no name is displayed or if there is a displayed name, you
are prompted to enter one. The screen indicates ENTER NAME. To enter or change
a name, use the dial pad. (See Entering Nameson page 11). If you don’t want to
add or change the name, go to step 7.
7. Press K.
8. If saved to Directory, the screen indicates SAVED: DIRECTORY. If saved to a mem-
ory key it indicates SAVED: MEMORY KEY.
To delete a number in the Callers List: To delete all numbers in the Callers List:
1. Press A. The screen displays
the number of items.
1. Press A. The screen displays
the number of items.
2. Press the WV to find the Caller
Record you wish to delete.
2. Press Luntil the display indi-
cates DELETE ALL?
3. Press L. The display indicates
PRESS DELETE, press Lagain.
3. Press Lagain and the display
briefly will indicate LIST EMPTY.
4. Press Nto exit the Callers List or
simply wait a few seconds and the
phone automatically exits the Callers
List.
4. Press A, the display will
briefly indicate NO CALLS.

15
Memory keys
Memory keys
Saving numbers and names into memory keys
You can save up to 15 speed dial numbers and names of your customers, business associ-
ates, or anyone you call frequently in the 9116LP’s eight memory keys. You can store more
numbers and names in the Directory. See the Directory on page 11 for more informa-
tion.
Note: You can also program a memory key by copying a caller record in the Callers
List. See To copy a number from the Callers List on page 14.
Viewing memory key contents
To save or edit a number and name in a memory key:
1. For a one touch memory key, press any of the seven lower memory keys. The
screen will show EMPTY or whatever name and number has already been pro-
grammed into the memory key. For a two touch memory key, press the H
(display will show SHIFT) and then one of the memory keys.
2. Press K. Display indicates SAVE TO?.
3. Press M. Display indicates ENTER NUMBER.
4. Enter the number using the dialpad. You can enter up to 16 digits. To add a
pause to a number, press O. To add Flash to a number, press B.
5. Press K. Display indicates ENTER NAME. If you do not wish to add a name for
the Memory key, go to the next step. To add a name, use the dialpad. See
Entering Names on page 11.
6. Press K. The display shows SAVED: MEMORY KEY.
To view an item in the memory key:
1. Press the memory key or the Hplus the memory key to view the contents of
that key.
2. Display screen will show any number and name programmed to that key. Dis-
play will briefly indicate EMPTY.

16
Memory keys
Labeling the memory keys
Your Memory key card has label identification spaces (shaded in grey) for each of the
eight programmable memory keys. Write the name of the autodialer or feature on
these spaces when you program a memory key.
Making calls from memory keys
Deleting memory keys
To call from a memory key: To predial from a memory key:
1. Lift the handset or press Q or
D.
1. Press the memory key, or Hplus
the memory key to obtain the num-
ber you wish to dial.
2. Press the memory key, or Hplus
the memory key to obtain the num-
ber you wish to dial.
2. Lift the handset or press either
Dor Q.
To delete a memory key:
1. To see its contents, press the memory key.
2. To erase, press Ltwice.
Options
Directory
Delete
Shift
Save

17
Memory keys
Saving features in memory keys†
For easy access, you can save the feature codes of telephone company services in your
memory keys. This works well with network features such as Call Forwarding and
Call Return. Some features require an On and Off code in two separate keys, while
other features are stored on only one key. The following procedures show you how to
save both an On and Off code.
Saving a feature and light in memory keys
You can make the set indicator light come on when you turn a feature on and go off
when you turn that same feature off. You can only do this with one feature, and the
feature must have separate On and Off codes (such as Call Forwarding).
For example, you may want the light to remind you that you have turned Call For-
warding on. To do this, use one key to turn the indicator light on when you activate
the feature. Use the second key to turn the indicator light off when you deactivate that
same feature. The following procedure shows you how to program a FeatureLight On
and Off key.
†You must subscribe to your telephone company for Custom Calling Features.
To save a Feature On code: To save a Feature Off code:
1. Press the memory key where you
want to save the number.
1. Press the memory key where you
want to save the number.
2. Press K. 2. Press K.
3. Enter the telephone company fea-
ture code for turning the feature on.†
Read the display to confirm the
number.
†Note: Contact your telephone company for the appropriate feature codes.
3. Enter the telephone company fea-
ture code for turning the feature off.†
Read the display to confirm the
number.
4. Press K. 4. Press K.
5. Enter the feature name using the dial
pad. (See Entering Names on
page 11.)
5. Enter the feature name using the dial
pad. (See Entering Names on
page 11.)
6. Press K. 6. Press K.
7. Label the memory key. 7. Label the memory key.