ABB SPA-ZC 402 User manual

Ethernet Adapter
Product Guide
SPA-ZC 402

3
Ethernet Adapter SPA-ZC 402
Features • Enables IEC 61850 connectivity for IEDs
with a fibre optic SPA bus.
• Auxiliary power supply
• Disturbance recorder file upload via
IEC 61850
• Easy-to-use configuration tool for the
IEC 61850 data mapping
• Communication over SPA/TCP
• Communication over Modbus/TCP
Application
a060239
Fig. 1 Conceptual picture of a typical system setup
Introduction
Using the SPA-ZC 402, an Intelligent Elec-
tronic Device (IED) with a fibre optic SPA
bus can be connected to the Ethernet based
IEC 61850-8-1 station bus.
IEC 61850 is the new standard for substation
communication. Additionally to being a com-
munication standard, it also supports general
substation automation functions as well as the
engineering process.
SPA-ZC 402 also enables ethernet access to
an IED using the SPA over TCP/IP and Mod-
bus over TCP/IP.
The SPA-ZC 402 acts as a communication
adapter between the SPA bus and the IEC
61850-8-1 station bus. The SPA-ZC 402
maps the SPA protocol interface to the IEC
61850-8-1 standard. This enables connecting
products with optical SPA interface to IEC
61850 based networks in both new and retro-
fit installations.
More information on how to physically con-
nect the device can be found in the chapter 5
of the Installation and Commissioning man-
ual. SPA-ZC 402 programming is described
in the Installation and commissioning man-
ual, chapter 6, Engineering.
As a prerequisite, you should understand the
communication properties of the IED that is
to be connected to Ethernet adapter. This
information is available in the manual for the
protection IED in question.
REF 542plus
COM600
1MRS755479
Issued: 08.12.2004
Status: Updated
Version: E/20.05.2009
Data subject to change without notice

Ethernet Adapter SPA-ZC 402
1MRS755479
4
Design Module parts
A040157b
Fig. 2 Parts of SPA-ZC 402
Technical data Interfaces
SPA-ZC 402 - IED interface
• ST multimode glass fibre transmit-
ter/receiver pair or
• Snap-in multimode plastic fibre transmit-
ter/receiver pair
IEC 61850 interface
LAN connectors
• RJ-45 (STP CAT5e) galvanic connection
• MT-RJ multimode glass fibre transceiver
• LC multimode glass fibre transceiver
Optical fibres
See fibre optic quides:
• SPA-ZF Optical glass fibres, multimode
graded index type specifications,
1MRS755371
• Plastic-core fibre optic cables, features and
instructions for mounting,
1MRS752089-MUM
Diagnostic leds
SPA-ZC 402 common diagnostic LEDs:
- Power
- Diagnostic:
-Red
- Green
LAN diagnostic LEDs:
- LINK
- TX
- RX
SPA diagnostic LEDs:
- TX
- RX
1. Ethernet connector
2. Fibre optic SPA-bus connectors
3. Auxiliary power supply connector
4. SPA TX and RX LEDs
5. LAN and diagnostic LEDs

Ethernet Adapter SPA-ZC 402
1MRS755479
Technical data (cont´d)
5
SPA-ZC402 dimensions and weight
A040027b
Fig. 3 SPA-ZC 402 dimensions
Tests and conditions
115 35
190 175
Use M5 mounting screws
SPA-ZC 402
ETHERNET ADAPTER
1MSC971158E
EXTERNAL
POWER
LN
+
PLASTIC GLASS
24-60 VDC
110-220 VDC, 100-240 VAC
DIAG
RX
TX
LINK
POWER
U
au
TX RX ETHERNET
LAN
IEC 61850
SPA / TCP
MODBUS / TCP
Type Dimensions [mm] Weight [g]
SPA-ZC 402 190 x 115 x 35 510
Environmental tests and conditions
Recommended service temperature range -10...+55°C (continuous)
Limit temperature range (short-term) -40...+70°C
Transport and storage temperature range -40...+85°C according to the IEC 60068-2-48
Dry heat test IEC 60068-2-2
Dry cold test IEC 60068-2-1
Damp heat test IEC 60068-2-30
Electromagnetic compatibility tests
EMC immunity test level meets the requirements listed below
1 MHz burst disturbance test, class III
Common mode
Differential mode
According to the IEC 60255-22-1
2.5 kV
1.0 kV
Electrostatic discharge test, class IV
For contact discharge
For air discharge
According to the IEC 6100-4-2 and
IEC 60255-22-2
8 kV
Not applicable

Ethernet Adapter SPA-ZC 402
1MRS755479
Technical data (cont´d)
6
RoHS Compliance
Radio frequency interference tests
Conducted, common mode
Radiated, amplitude-modulated
Radiated, pulse-modulated
According to the IEC 61000-4-6 and
IEC 60255-22-6
10 V (rms), f = 150 kHz ... 80 MHz
According to the IEC 61000-4-3 and
IEC 60255-22-3
10 V/m (rms), f = 80 ... 2700 MHz
According to the ENV 50204 and
IEC 60255-22-3
10 V/m, f = 900 MHz
Fast transient disturbance tests
All terminals
According to the IEC 60255-22-4 and
IEC 61000-4-4
4 kV
Surge immunity test
Power supply SPA-ZC402xxxA
Power supply SPA-ZC402xxxC
RJ-45 cable
According to the IEC 60255-22-5 and IEC 61000-4-5
4 kV, line to earth
2 kV, line to line
2 kV, line to earth
1 kV, line to line
2 kV, line to earth
Power frequency (50 Hz) magnetic field According to the IEC 61000-4-8
300 A/m continuous
Electromagnetic emission tests
Conducted, RF-emission (Mains term.)
Radiated RF-emission
According to the EN 55011
EN 55011, class A, IEC 60255-25
EN 55011, class A, IEC 60255-25
CE compliance Complies with the EMC directive 2004/108/EC and the LV
directive 2006/95/EC
Standard tests
Mechanical tests
Vibration tests (sinusoidal)
Shock and bumb test
According to the IEC 60255-21-1, class I
According to the IEC 60255-21-2, class I
Auxiliary power supplies
Type SPA-ZC 402 xxxA SPA-ZC 402 xxxC
Input voltage AC 110/120/220/240 V -
Input voltage DC 110/125/220 V 24/48/64 V
Voltage variation AC 85...110%, DC 80...120% of
rated value
DC 80.120% of rated value
Burden <4W
Ripple in DC auxiliary voltage max. 12% of rated DC value (IEC 60255-11)
Interruption time in auxiliary DC
voltage without resetting
110 V < 40ms 24 V < 24ms
Electromagnetic compatibility tests
Complies with the RoHS directive 2002/95/EC

Ethernet Adapter SPA-ZC 402
1MRS755479
7
Ordering
A060159
Fig. 4 Ordering information for SPA-ZC402
SPA-ZC 402CD
• SPA-ZC 402 configuration CD
• Communication Engineering Tool
(CET) for SPA-ZC 40x.
Order at least one SPA-ZC 402 configu-
ration CD with your delivery to get the Com-
munication Engineering Tool.
The connectivity packages for a set of
ABB IEDs can be found from the internet
address: http://www.abb.com/substationauto-
mation. Please contact ABB to check the con-
nectivity package’s status for the IED in
question.
References Related documents
SPA-ZC402MMPA
Et ernet connector type
M = MTRJ
L=LC
R = RJ-45
Protocol type
M = Modbus/TCP
E = IEC 61850
S = SPA/TCP
Device type
Optical transmitter and receiver for SPA bus
P = plastic fibre cable
G = glass fibre cable
Auxiliary voltage
A = 100-240 V AC, 110-220 V DC
C = 24-60 V DC
Name of the document Document id
SPA-ZC 402 Installation and commissioning manual 1MRS755380
SPA-ZC 402 configuration CD 1MR151049
CAP 505 User’s Guide 1MRS752292-MUM
SPA-ZF Optical glass fibres, multimode graded index
type specifications
1MRS755371
Plastic-core fibre optic cables, features and
instructions for mounting
1MRS752089
Standard IEC 61850, parts -6, -7-2, -7-3, -7-4, -8-1

ABB Oy
Distribution Automation
P.O. Box 699
FI-65101 Vaasa, FINLAND
Tel [phone]
Fax [phone]
www.abb.com/substationautomation