ABB COPYSTICK2 User manual

Compatibility
This Option is suitable for use on the following product ranges:
EC Titanium
Model No.
ECS 100B
Compliance
Hereby, ABB declares that the radio equipment type Bluetooth
Wireless Access Point, model COPYSTICK2, is in compliance
with Directive 2014/53/EU.
The full test of the EU declaration of conformity is available by
contacting ABB.
Overview
The COPYSTICK2 is used for fast and accurate repeat drive
programming.
NOTE: Parameters can only be copied between drives of
the same product range and power rating (size).
User Guide
COPYSTICK2
Lock/Unlock
Locks COPYSTICK2
parameter set so it cannot
be over-written (Transfer
Parameters from the DRIVE
function disabled)
Bluetooth Status
Feedback / Activity Indicators
Optistick Interface
Connects to RJ45
slot on the DRIVE
(see pr
oduct
manual for futher
information)
Write
Transfer
Parameters &
PLC Program
to the DRIVE
Read
Transfer
Parameters &
PLC Program
from the DRIVE

—
ABB Motors and Mechanical Inc.
5711 R. S. Boreham Jr. Street
Fort Smith, AR 72901
Ph: 1.479.646.4711
Mechanical Power Transmission Support
Ph: 1.864.297.4800
new.abb.com/mechanical-power-transmission
baldor.com
All Rights Reserved. Printed in USA.
08/19
*450-0719*
© ABB Motors and Mechanical Inc.
MN450
Copying Data from a Drive
Action Description
Insert the COPYSTICK2 into the RJ45 port
on the DRIVE
Wait for the COPYSTICK2 to complete its
boot sequence
The COPYSTICK2 is ready when the up-
arrow and the padlock symbol are displayed
Before attempting to download data, unlock
the COPYSTICK2 by touching the padlock
symbol until the LEDs stop ashing
Information for Compliance
USA (FCC)
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
5. Caution: Exposure to Radio Frequency Radiation.
Action Description
When the COPYSTICK2 is unlocked both
green arrows are displayed
Touch the lower arrow to initiate data
download from the DRIVE
Wait until the COPYSTICK2 LEDs stop
ashing. Some DRIVES require multiple les
which may take up to 30 seconds to transfer
Once Download is complete the
COPYSTICK2 will automatically re-lock,
with the up-arrow and the padlock symbol
displayed\
Remove the COPYSTICK2 from the DRIVE
Canada – Industry Canada (IC)
This device complies with Industry Canada’s license-exempt RSSs. Operation is
subject to the following two conditions:
1. This device may not cause interference; and
2. This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes:
1. l’appareil ne doit pas produire de brouillage;
2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
The installer of this radio equipment must ensure that the antenna is located or
pointed such that it does not emit RF eld in excess of Health Canada limits for
the general population; consult Safety Code 6, obtainable from Health Canada’s
website www.hc-sc.gc.ca/rpb
82-REM-PAN-ABM_v2