ABB Type A Operating and maintenance manual

General description
Type A bushings are designed for application on transformers.
Porcelain is used as the major insulation, and the single-piece
porcelain is bottom end connected to the apparatus to insulate
the conductor from the grounded mounting surface.
Type A bushings are available with voltage ratings from 1.2 to
34.5 kV. Bushings rated 600 amperes and lower have draw-
lead conductors which allow the bushings to be removed
without disturbing connections inside the transformer. Fixed
conductor bushings are available in current ratings through
18,000 amperes.
The fixed conductor bushings are center clamped with spring
washers or multiple spring mechanisms at the bottom end.
This construction provides a pressure tight seal and develops
maximum strength in the porcelain.
Safety information
Keep this document available to those responsible for the
installation, operating, and maintenance of the bushing.
The installation, operation, and maintenance of a bushing
present numerous unsafe conditions, including, but not limited
to, the following:
– High pressures
– Lethal voltages
– Moving machinery
– Heavy components
Specialized procedures and instructions are required and must
be adhered to when working on power transformers. Failure to
follow instructions could result in severe personal injury, death,
and/or product or property damage.
Additionally, all applicable safety procedures such as OSHA
requirements, regional and local safety requirements, safe
working practices, and good judgment must be used by
personnel when installing, operating, and/or maintaining such
equipment.
Safety, as defined in this document, involves two conditions:
– Personal injury or death
– Product or property damage (includes damage to the
bushing or other property, and reduced bushing life.)
Safety notations are intended to alert personnel of possible
personal injury, death or property damage. They have been
inserted in the instructional text prior to the step in which the
condition is cited. The safety notations are headed by one of
three hazard intensity levels which are defined as follows:
– Danger - immediate hazard which will result in severe
personal injury, death, or property damage.
– Warning - hazard or unsafe practice which could result in
severe personal injury, death, or property damage.
– Caution - hazard or unsafe practice which could result in
minor personal injury, or property damage.
This document contains general
procedures to be followed from the time
bushings are received until they are put
into operation.
Receiving and unpacking
When a bushing is received, examine any damage incurred
during shipment. Inspect the surface of the porcelain for small
breaks or cracks. If damage or rough handling is evident, file a
claim with the transportation company and immediately notify
ABB.
Exercise care in opening the shipping container to prevent
damage to the porcelain insulators. As each bushing is
Transformer components
Type A bushings
Instructions for installation, maintenance, and storage

2 Type A bushing
Storing
Store the bushing in a clean, dry place in the shipping crate.
Particular care should be taken to keep dust and dirt out of
the inside of the bushing. For long term storage, suitable
protection should be provided for the terminals and mounting
hardware. The gasket surface on the underside of the mounting
flange should be heavily greased to protect it from rust and
corrosion.
Installation
Type A bushings are shipped ready for installation. An
apparatus manufacturer may ship the bushing completely
installed, eliminating the requirement for installation in the
field. If a draw-lead bushing is removed from the transformer
for shipment, the top hardware and mounting hardware may
be removed from the bushing and packed separately. When
installing a bushing, tighten the mounting bolts a fraction of
a turn at a time, working progressively in a crisscross pattern
Draw-lead bushings
The draw-lead terminal stud for a low current bushing is
included as an integral part of the bushing. The flexible draw-
lead cable is provided by the transformer manufacturer. The
terminal stud is either brazed or crimped on to the draw-lead
cable. Remove the terminal cap, retaining pin, and stud
washer. Assemble the stud washer onto the terminal stud.
Pass a wire or cord down through the tubular porcelain and
attach it to the terminal stud on the draw-lead. Lower the
bushing into position while pulling the draw-lead up through
the porcelain. Pin the terminal stud into position. Coat the
terminal cap gasket with a thin film of light oil; then position the
gasket in the terminal cap. Tighten the terminal on the stud to
compress the gasket, thus sealing the bushing.
On a bushing of older design, the stud is brought into position
with a sealing nut. Remove the terminal cap and sealing nut
(the stud is already removed) from the top end of the bushing.
After positioning the terminal stud in the porcelain, assemble
the gasket and sealing nut on the stud. Screw on the nut
tightly to compress the gasket and seal the nut. The draw-
lead bushing uses a multiple-piece clamp, illustrated in Figure
3 for mounting on the transformer. The clamp does not require
cement.
unpacked, wipe clean of all dust, grease, oil or particles of
packing material with a dry cloth. Inspect the bushing for
damage such as cracked porcelain or damaged threads.
Type A features
The draw-lead bushing has a pin connected terminal stud.
Standard bushings rated up through 2,500 amperes use a
loose, multi-piece mounting clamp (see Figure 3). Standard
bushings rated 3,000 amperes and above have an epoxy
cement flange. A fixed conductor bushing up to 3,000 amperes
for cover or side-wall mounting is not sealed at the bottom end,
allowing oil from the transformer to circulate in the bushing.
The Type A bushing has satisfactory radio influence voltage
characteristics under normal operating conditions. The
electrical characteristics comply with ANSI requirements. The
construction is simple and sturdy and the Type A bushing has
an excellent service record.
Size of bolt (inch-thread) Torque ft-lbf (N-m)
1
1/2 - 13 25 (34)
5/8 - 11 30 (41)
3/4 - 10 35 (48)
1
Torque values for mounting bolts should not be exceeded
Figure 1 - Type A bushing (600 amperes and below)
until all of the bolts are uniformly tight. This must be done
to prevent unequal clamping and possible damage to the
porcelain support or the mounting flange. Tighten the bolts
sufficiently to seal the bushing to the mounting flange. The
torque values listed below will provide adequate gasket
compression for sealing on all Type A bushings.

Type A bushing 3
External line connections
Connections from a bus to the top end of a bushing should
be made securely to avoid loosening in service which would
cause damage to bushing gaskets. There should be sufficient
flexibility in the connections to prevent mechanical stresses
from expansion, contraction, and wind sway. Long spans of
unsupported conductor should be avoided.
Terminal connectors should be of ample size to keep the
bushing terminal temperature below 70 °C at rated current. The
use of even more generously sized connectors is recommended
to minimize bushing overheating during possible overloads. Do
not loosen the top terminals when installing the line terminal
connectors.
Fixed conductor bushing
A cover or side-wall bushing up to 3,000 amperes, with a fixed
conductor, is not sealed at the bottom (inboard) end. Insulating
oil from the transformer is permitted to enter the bushing when
it is installed and operating. Threaded clamping members at the
bottom end are assembled to seal the top (outboard) end of the
bushing with a gasket and to load the porcelain in compression.
Fixed conductor bushings rated 3,000 amperes or more
have epoxy bonded supports and gasket-to-porcelain seals.
Sometimes a clamping ring is attached with epoxy and then
bolted to a mounting support plate. Thin washers or shims are
used between the clamping ring and the support plate. These
are installed at the factory.
Do not alter the position of the washers; otherwise, leaks may
occur. Bushings with fixed conductors should be bolted to
the transformer prior to making bottom and top end terminal
connections.
!Caution
Before applying vacuum to a transformer, be certain there
is sufficient slack in the external line connections to the
bushing to allow for bushing movement caused by flexing
of the transformer cover and/or walls. Failure to relieve this
stress at the bushing connection may result in damage to
the bushing seals and loss of oil. Loss of oil will cause an
electrical failure.
Maintenance
Porcelain is the major insulation in Type A bushings and requires
little maintenance other than cleaning when operated under
very dirty conditions. Inspection should be made regularly
for cracked porcelains which could contribute to oil leakage,
especially on self-filling, side-wall mounted bushings or on
bushings used with transformers equipped with an oil expansion
tank above the cover level.
Nameplate data
Nameplate data is of special importance in answering questions
about bushings. All requests will be expedited if the factory is
furnished with the serial number, the functional style number,
version number, and the year of manufacture as stamped on the
bushing nameplate.
At a minimum, the factory should be provided with the serial
number of the bushing in question.
Field repair
Any repair of Type A bushings should be done in the factory
because of the danger of contamination to the insulation when
the seal is broken. In addition, the very high vacuum and
clamping pressure require the use of equipment not usually
available in the field. Any damage to a bushing, which might
make repair either desirable or necessary, should be reported to
the factory.
Figure 2 - Type A bushing with fixed conductor (2,000 amperes)
Figure 3 - Typical mounting clamp and cushion for bushings rated <2500A

For more information please contact:
ABB Inc.
1133 South Cavalier Drive
Alamo, Tennessee 38001, USA
Phone: [phone]
Main: [phone]
Fax: [phone]
www.abb.com/electricalcomponents
Note:
The information contained in this document is for general information purposes
only. While ABB strives to keep the information up to date and correct, it makes
no representations or warranties of any kind, express or implied, about the
completeness, accuracy, reliability, suitability or availability with respect to the
information, products, services, or related graphics contained in the document for
any purpose. Any reliance placed on such information is therefore strictly at your
own risk. ABB reserves the right to discontinue any product or service at any
time.
Copyright © 2011 ABB. All rights reserved.
1ZUA276100-220, rev. 2