ABB ACS 800 Series User manual

ACS800
Cabinet Installation
ACS800-04 and ACS800-04M Drive Modules (45 to 560 kW)
ACS800-U4 Drive Modules (60 to 600 HP)

ACS800 Single Drive Manuals
HARDWARE MANUALS (appropriate manual is included in the
delivery)
ACS800-01/U1 Hardware Manual 0.55 to 160 kW (0.75 to 200 HP)
3AFE64382101 (English)
ACS800-01/U1/04 Marine Supplement 0.55 to 160 kW (0.75 to
200 HP) 3AFE64291275 (English)
ACS800-11/U11 Hardware Manual 5.5 to 110 kW (7.5 to 125 HP)
3AFE68367883 (English)
ACS800-31/U31 Hardware Manual 5.5 to110 kW (7.5 to 125 HP)
3AFE68599954 (English)
ACS800-02/U2 Hardware Manual 90 to 500 kW (125 to 600 HP)
3AFE64567373 (English)
ACS800-04/U4 Hardware Manual 0.55 to 160 kW (0.75 to 200 HP)
3AFE68372984 (English)
ACS800-04/04M/U4 Hardware Manual 45 to 560 kW (60 to
600 HP) 3AFE64671006 (English)
ACS800-04/04M/U4 Cabinet Installation 45 to 560 kW (60 to
600 HP) 3AFE68360323 (English)
ACS800-07/U7 Hardware Manual 45 to 560 kW (50 to 600 HP)
3AFE64702165 (English)
ACS800-07/U7 Dimensional Drawings 45 to 560 kW (50 to
600 HP) 3AFE64775421
ACS800-07 Hardware Manual 500 to 2800 kW
3AFE64731165 (English)
ACS800-17 Hardware Manual 55 to 2500 kW (75 to 2800 HP)
3AFE68397260 (English)
ACS800-37 Hardware Manual 55 to 2700 kW (75 to 3000 HP)
3AFE68557925 (English)
• Safety instructions
• Electrical installation planning
• Mechanical and electrical installation
• Motor control and I/O board (RMIO)
• Maintenance
• Technical data
• Dimensional drawings
• Resistor braking
FIRMWARE MANUALS, SUPPLEMENTS AND GUIDES
(appropriate documents are included in the delivery)
Standard Control Program Firmware Manual
3AFE64527592 (English)
System Control Program Firmware Manual
3AFE64670646 (English)
Control Program Template Firmware Manual
3AFE64616340 (English)
Master/Follower 3AFE64590430 (English)
Pump Control Program Firmware Manual
3AFE68478952 (English)
Extruder Control Program Supplement 3AFE64648543 (English)
Centrifuge Control Program Supplement 3AFE64667246 (English)
Traverse Control Program Supplement 3AFE64618334 (English)
Crane Control Program Firmware Manual 3BSE11179 (English)
Adaptive Programming Application Guide
3AFE64527274 (English)
OPTION MANUALS (delivered with optional equipment)
Fieldbus Adapters, I/O Extension Modules etc.

ACS800-04 and ACS800-04M Drive Modules
45 to 560 kW
ACS800-U4 Drive Modules
60 to 600 HP
Cabinet Installation
3AFE68360323 Rev B EN
EFFECTIVE: 14.2.2008
©2008 ABB Oy. All Rights Reserved.

Table of contents
5
Table of contents
ACS800 Single Drive Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Table of contents
About this manual
What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Target audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Other related manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Categorization according to the frame size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Categorization according to the plus code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Installation, commissioning and operating flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Product and service inquiries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Product training . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Providing feedback on ABB Drives manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
The ACS800-04/U4 and ACS800-04M
What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
The ACS800-04/U4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
The ACS800-04M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Example configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Type designation label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Type code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Main circuit and control interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Connections of the Drive Control Unit (RDCU) in frame sizes R7 and R8 . . . . . . . . . . . . . . . . 21
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Printed circuit boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Motor control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Planning the cabinet installation
What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Cabinet construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Disposition of the devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Layout examples, door closed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Layout examples, door open . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Grounding of mounting structures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Busbar material and joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Tightening torques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Table of contents
6
Cabinet cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Cabinet cooling data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
IP 22 cabinet with no extra fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
IP 54 cabinet with an extra fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Preventing the recirculation of hot air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Outside the cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Inside the cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Cubicle heaters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Required free space around the drive module for cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Free space at the top of the drive module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Free space around units with busbars on the long side (bookshelf mounting +H354) . . . . . . . 31
Free space around units with busbars on the short side (flat mounting +H360) . . . . . . . . . . . 32
When the drive module is installed in another position than vertically . . . . . . . . . . . . . . . . . . . . . . 33
Drive module of frame size R7 on its side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Drive module of frame size R7 on its back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
EMC requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Grounding of cable shields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Installing the Drive Control Unit (RDCU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Fastening of the control panel (CDP312R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Installing the control panel directly on the cabinet door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Control Panel Mounting Platform RPMP-11/13 (+J410) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Control Panel Holder RPMP-21 (+J413) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Mechanical installation of pre-assembled units (ACS800-04/U4)
What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Moving and unpacking the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Delivery check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Required tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Installation procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Fasten the module to the cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Clamping the pedestal with the outside brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Fasten the terminals to the busbars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
View of output busbar connections of frame size R7 (DC and brake busbars included) . . . 43
View of output busbar connections of frame size R8 (DC and brake busbars included) . . 44
User connections of Prevention of Unexpected Start (+Q950) . . . . . . . . . . . . . . . . . . . . . . . . . 44
Mechanical installation of non-pre-assembled units (ACS800-04M)
What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
How to read this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Units with bottom exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Units with pedestal and busbars on the long side (+H354, bookshelf mounting) . . . . . . . . . . . 45
Units with pedestal and busbars on the short side (+H360, flat mounting) . . . . . . . . . . . . . . . . 45
Required tools and tightening torques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Moving and unpacking the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Table of contents
7
Frame size R7 units with bottom exit (+H352) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Delivery check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Assembling procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Fastening the spacer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Fastening the top entry busbar and bottom exit shrouds (+B060) . . . . . . . . . . . . . . . . . . . . . . . 55
Top entry busbar shroud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Bottom exit shroud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Units with pedestal and busbars on the long side (+H354, bookshelf mounting) . . . . . . . . . . . . . . 57
Delivery check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Item packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Item packages of frame size R7 with busbars on the long side . . . . . . . . . . . . . . . . . . . . . . . 58
Item packages of frame size R8 with busbars on the long side . . . . . . . . . . . . . . . . . . . . . . 64
Assembling procedure for units with busbars on the long side (+H354) . . . . . . . . . . . . . . . . . . . . . 73
Working order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Connecting the DC busbars to the pedestal (+H356 and +H363 only) . . . . . . . . . . . . . . . . . . . 76
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Photos of frame size R7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Photos of frame size R8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Busbars to the left- or right-hand side of the module? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Swapping the busbars of the pedestal to the other side . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Optional selection +H363 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Fastening the pedestal to the cabinet base (not for wall-mounted units) . . . . . . . . . . . . . . . . . . 80
Clamping the pedestal with the outside brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Fastening the pedestal through the holes inside the pedestal . . . . . . . . . . . . . . . . . . . . . . . . 80
Fastening the drive module by top to the cabinet frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Fastening the drive module to wall (wall-mounted units only, not for base-mounted units) . . . . 81
Requirements for protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Requirements for the wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Floor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Fastening the output busbars and PE terminal and sliding the module in . . . . . . . . . . . . . . . . . 86
View of output busbar connections of frame size R7 (DC and brake busbars included) . . . 87
View of output busbar connections of frame size R8 (DC and brake busbars included) . . . 88
Fastening the drive module to the pedestal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Fastening the shrouds in frame size R8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Top entry busbar shroud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Vertical busbar shroud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Units with pedestal and busbars on the short side (+H360, flat mounting) . . . . . . . . . . . . . . . . . . . 91
Delivery check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Item packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Item packages of frame size R7 with busbars on the short side . . . . . . . . . . . . . . . . . . . . . . 92
Item packages of frame size R8 with busbars on the short side . . . . . . . . . . . . . . . . . . . . . 98

Table of contents
8
Assembling procedure for units with busbars on the short side (+H360) . . . . . . . . . . . . . . . . . . . 104
Working order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Swapping the pedestal output busbars to the left-hand side . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Connecting the DC busbars to the pedestal (+H360 +H356 only) . . . . . . . . . . . . . . . . . . . . . . 107
Required parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Preparing the adapter (+H360 +H356 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Required parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Fastening the adapter to the drive module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Fastening the drive module to the pedestal via the adapter . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Connecting the output busbars on the short side of the module . . . . . . . . . . . . . . . . . . . . . . . 111
Procedure for frame size R7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Procedure frame size R8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Checking the installation
What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Visual inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Cabinet construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Instrumentation, busbars and cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Groundings and protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Labels, switches, fuses and doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Dimensional drawings
Frame size R7 without pedestal (mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Frame size R7 with bottom exit (mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Frame size R7 with bottom exit and top entry and bottom exit shrouds (mm) . . . . . . . . . . . . . . 122
Frame size R7 with busbars on the left side (mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Frame size R7 with DC busbars on both sides (mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Frame size R7 pedestal busbars on the long side (mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Frame size R7 with busbars on the short side (mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Frame size R8 without pedestal (mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Frame size R8 with busbars on the left side (mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Frame size R8 with top entry and vertical busbar shrouds (mm) . . . . . . . . . . . . . . . . . . . . . . . . . 129
Frame size R8 with busbars on both sides (mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Frame size R8 pedestal busbars on the long side (mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Frame size R8 with busbars on the short side (mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Wall mounting spacers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Frame size R7 bottom exit kit (+H352) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Frame size R7 top entry busbar shroud and bottom exit shroud (+B060) . . . . . . . . . . . . . . . . . . 135
Control Panel Holder RPMP-21 (+J413) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Drive Control Unit (RDCU-02) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137

Table of contents
9
Dimensional drawings (USA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Frame size R7 without pedestal (inches) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Frame size R7 with bottom exit (inches) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Frame size R7 with bottom exit and top entry and bottom exit shrouds (inches) . . . . . . . . . . . 141
Frame size R7 with busbars on the left side (inches) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Frame size R7 with busbars on both sides (inches) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Frame size R7 pedestal busbars on the long side (inches) . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Frame size R7 with busbars on the short side (inches) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Frame size R8 without pedestal (inches) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Frame size R8 with busbars on the left side (inches) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Frame size R8 with top entry and vertical busbar shrouds (inches) . . . . . . . . . . . . . . . . . . . . . 148
Frame size R8 with busbars on both sides (inches) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Frame size R8 pedestal busbars on the long side (inches) . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Frame size R8 with busbars on the short side (inches) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Circuit diagrams
What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Assembly drawings
What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Adding UDC+/R+, UDC- and R- busbars to the pedestal (frame size R7, +H356+H360) . . . . . . 156
Adding UDC+/R+, UDC- and R- busbars to the adapter (frame size R7, +H356+H360) . . . . . . . 157
Adding UDC+/R+, UDC- and R- busbars to the pedestal (frame size R8, +H356+H360) . . . . . . 158
Adding UDC+/R+, UDC- and R- busbars to the adapter (frame size R8, +H356+H360) . . . . . . . 159

Table of contents
10

About this manual
11
About this manual
What this chapter contains
This chapter describes the intended audience and contents of the manual. It
contains a flowchart of steps in checking the delivery, installing and commissioning
the drive. The flowchart refers to chapters/sections in this manual and other
manuals.
Target audience
This manual is intended for people who plan the installation, and install the drive
module into a user-defined cabinet. Read the manual before the installation work.
The reader is expected to know the fundamentals of electricity, wiring, electrical
components and electrical schematic symbols.
The manual is written for readers worldwide. Both SI and imperial units are shown.
Special US instructions for installations within the United States that must be
installed per the National Electrical Code and local codes are marked with (US).
Safety
WARNING! Follow the safety instructions given in ACS800-04/04M/U4 Hardware
Manual [3AFE64671006 (English)] when installing, operating and servicing the drive.
If ignored, physical injury or death may follow, or damage may occur to the drive, the
motor or driven equipment. Read the safety instructions before you work on the unit.
Other related manuals
See ACS800-04/04M/U4 Hardware Manual [3AFE64671006 (English)] for
information concerning the drive module such as
• safety
• planning the electrical installation
• electrical installation
• motor control and I/O board (RMIO)
• maintenance
• technical data
• resistor braking.

About this manual
12
For installation instructions of optional equipment, see their manuals.
For example installations in Rittal TS 8 cabinet, refer to ACS800-04/U4 Rittal TS 8
Cabinet Installation [3AFE68372330 (English)].
Categorization according to the frame size
The instructions, technical data and dimensional drawings which concern only
certain frame sizes are marked with the symbol of the frame size R7 or R8. The
frame size is not marked on the drive designation label. To identify the frame size of
your drive, see the rating tables in chapter Technical data in ACS800-04/04M/U4
Hardware Manual [3AFE64671006 (English)].
Categorization according to the plus code
The instructions, technical data and dimensional drawings which concern only
certain optional selections are marked with plus codes, e.g. +E210 or +H354. The
options included in the drive can be identified from the plus codes visible on the type
designation label of the drive. The plus code selections are listed in chapter The
ACS800-04/U4 and ACS800-04M under Type code.
Contents
The chapters of this manual are briefly described below.
About this manual introduces this manual.
The ACS800-04/U4 and ACS800-04M describes the drive module.
Planning the cabinet installation instructs on general cabinet design, gives layout
examples, free space requirements around the drive module for cooling and cabinet
cooling data.
Mechanical installation of pre-assembled units (ACS800-04/U4) instructs how to
mount a pre-assembled drive module into a cabinet.
Mechanical installation of non-pre-assembled units (ACS800-04M) instructs how to
assemble the drive from the assembly kits.
Checking the installation helps in checking the mechanical and electrical installation
of the drive.
Dimensional drawings contains the dimensional drawings of the drive modules.
Circuit diagrams shows an example circuit diagram for employing the Prevention of
Unexpected Start function (+Q950).
Assembly drawings contains a few step-by-step assembly drawings.

About this manual
13
Installation, commissioning and operating flowchart
Task Chapters in this manual Chapters in ACS800-04/04M/U4
Hardware Manual
[3AFE64671006 (English)]
Identify the frame size of your drive, R7 or R8. -Technical data / IEC ratings or
NEMA ratings
Plan the installation.
Check the ambient conditions, ratings,
required cooling air flow, input power
connection, compatibility of the motor, motor
connection, and other technical data.
Planning the cabinet installation
If optional equipment is included, see
its manuals.
Technical data
Planning the electrical installation
Unpack and check the units.
Check that all necessary optional modules
and equipment are present and correct.
Only intact units may be started up.
Mechanical installation of pre-
assembled units (ACS800-04/U4) or
Mechanical installation of non-pre-
assembled units (ACS800-04M)
If the converter has been non-
operational for more than one year,
the converter DC link capacitors need
to be reformed. Ask ABB for
instructions.
-
Assemble and install the drive module into the
cabinet.
Mechanical installation of pre-
assembled units (ACS800-04/U4) or
Mechanical installation of non-pre-
assembled units (ACS800-04M)
Install the RDCU drive control unit. -See RDCU Drive Control Unit
Hardware Manual
[3AFE64636324 (English)]
Check the installation. Checking the installation -
Electrical installation - Safety, Planning the electrical
installation, Electrical installation,
Maintenance, Technical Data,
Resistor braking
Commissioning and operating the drive - See the appropriate firmware
manual.

About this manual
14
Product and service inquiries
Address any inquiries about the product to your local ABB representative, quoting
the type code and serial number of the unit in question. A listing of ABB sales,
support and service contacts can be found by navigating to www.abb.com/drives and
selecting Drives – World wide service contacts on the right pane.
Product training
For information on ABB product training, navigate to www.abb.com/drives and select
Drives – Training courses on the right pane.
Providing feedback on ABB Drives manuals
Your comments on our manuals are welcome. Go to www.abb.com/drives, then
select successively Drives – Document Library – Manuals feedback form on the right
pane.

The ACS800-04/U4 and ACS800-04M
15
The ACS800-04/U4 and ACS800-04M
What this chapter contains
This chapter describes the construction and operating principle of the drive in short.
The ACS800-04/U4
The ACS800-04/U4 is an IP 00 drive module for controlling AC motors. It is to be
installed into a cabinet by the customer with base or wall fastening. The input cable
terminals are located at the top of the unit whereas the motor cable terminals are
located at the left- or right-hand side of the unit. The unit is delivered pre-assembled
with mounting pedestal and output busbars.
Front cover
Pedestal
Motor cable terminals
Input cable terminals
Optional brake and DC
busbars and terminals
PE terminal
Slots for cables going to the RMIO board in the RDCU unit. The cables are coiled
on the top of the module.
Alternative output cable
terminals (when no
vertical busbars are used)
Fastening bracket
Fastening points
Fastening points
Additional holes for fastening the cable
terminals
Fastening points
Drive Control Unit
(RDCU)
Terminal block for user connection
of optional Prevention of
Unexpected Start (+Q950). See
ACS800-04/04M/U4 Cabinet
Installation [3AFE68360323
(English)] chapter Circuit diagrams.

The ACS800-04/U4 and ACS800-04M
16
The ACS800-04M
The ACS800-04M is delivered as non-pre-assembled kits, which provide more
alternatives in assembling the units than the basic ACS800-04.
Example configurations
Motor and brake busbars on the
right-hand long side of the module
and DC busbars on the left-hand
side
Output busbars on the short
side of the module
Motor and brake busbars on the
left-hand long side of the module
and DC busbars on the right-hand
side
Frame size R8
Output busbars on the short
side of the module
Frame size R7
Frame size R7 with bottom exit
(optional top entry busbar
shroud and bottom exit shroud
included). Output busbars are
located at the base of the
module.
Drive Control Unit
(RDCU)

The ACS800-04/U4 and ACS800-04M
17
Type designation label
The type designation label includes an IEC and NEMA rating, C-UL US, and CSA
markings, a type code and a serial number, which allow individual recognition of
each unit. The first digit of the serial number refers to the manufacturing plant. The
next four digits refer to the unit’s manufacturing year and week respectively. The
remaining digits complete the serial number so that there are no two units with the
same serial number.
The type designation label is located on the front cover and the serial number label
inside the unit. Example labels are shown below.

The ACS800-04/U4 and ACS800-04M
18
Type code
The type code contains information on the specifications and configuration of the
drive. The first digits from left express the basic configuration (e.g. ACS800-04-
0170-5). The optional selections are given thereafter, separated by plus signs (e.g.
+E202). The main selections are described below. Not all selections are available for
all types. For more information, refer to ACS800 Ordering Information (EN code:
64556568, available on request).
Type code for ACS800-04 and ACS800-U4 pre-assembled units
Selection Alternatives
Product series ACS800 product series
Type 04 Drive module. When no options are selected: 6-pulse diode input bridge, IP 00, top
entry, side exit, RDCU drive control unit, no control panel, no EMC filter, Standard
Control Program, boards without coating, pedestal with output on the long side, output
busbar set for motor, base and wall mounting brackets, one set of manuals. Pre-
assembled unit.
U4 Drive module (USA). When no options are selected: 6-pulse diode bridge, open
chassis, top entry, side exit, no control panel, no EMC filter, US version of the
Standard Control Program (three-wire start/stop as default setting), common mode
filter in frame size R8, boards without coating, pedestal with output on the long side,
output busbar set for motor, base and wall mounting brackets, one set of manuals.
Pre-assembled unit.
Size Refer to Technical data: IEC ratings or NEMA ratings in Hardware Manual [3AFE64671006
(English)].
Voltage range
(nominal rating in bold)
2 208/220/230/240 VAC
3 380/400/415 VAC
5 380/400/415/440/460/480/500 VAC
7 525/575/600/690 VAC
+ options
Resistor braking D150 brake chopper and busbars for brake resistor and DC connection
Filter E210 EMC/RFI filter for second environment TN/IT (grounded/ungrounded) system
E208 common mode filter
Pedestal and output
busbars
0H354 no pedestal
Control panel J400 control panel including a 3-metre panel connection cable
J410 RPMP-11 control panel mounting platform kit including a 3-metre panel connection
cable but no control panel
J413 RPMP-21 control panel holder
Fieldbus K... Refer to ACS800 Ordering Information (EN code: 64556568).
I/O L...
Control program N...
Language of manual R...
Specialities P901 coated boards
Safety features Q950 Prevention of Unexpected Start, 500 mm (19.68 in.) cable outside the drive module in
frame size R7, 600 mm (23.62 in.) cable outside the drive module in frame size R8.

The ACS800-04/U4 and ACS800-04M
19
Type code for ACS800-04M non-pre-assembled units (delivered as kits)
Selection Alternatives
Product series ACS800 product series
Type 04M Drive module. When no options are selected: 6-pulse diode input bridge, IP 00, top
entry, RDCU drive control unit, Standard Control Program, boards without coating,
one set of manuals. No pedestal, no output busbars, no control panel, no EMC filter.
Delivered as kits.
Size Refer to Technical data: IEC ratings in Hardware Manual [3AFE64671006 (English)].
Voltage range
(nominal rating in bold)
2 208/220/230/240 VAC
3380/400/415 VAC
5 380/400/415/440/460/480/500 VAC
7 525/575/600/690 VAC
+ options
Shrouds B060 Frame size R7: clear plastic shrouds for bottom exit kit (+H352) and input terminals.
Frame size R8: clear plastic shrouds for vertical busbars and input terminals in
bookshelf mounting (+H354)
Resistor braking D150 brake chopper
Filter E202 EMC/RFI filter for first environment TN (grounded) system, restricted (the A limits)
E210 EMC/RFI filter for second environment TN/IT (grounded/ungrounded) system
E208 common mode filter
Pedestal and output
busbars
H352 bottom exit kit for frame size R7
H354 pedestal with output on the long side (bookshelf)
H355 vertical busbars and support brackets for AC output connection
H356 pedestal (and adapter with +H360) busbar kit for brake resistor and DC connection
H360 pedestal with output on the short side (flat)
H362 vertical busbars (and support brackets with +H360) for DC output connection
H363 busbar kit for DC and brake outputs on different long sides of the pedestal (+H356
required, not available for +H360)
Control panel J400 control panel including a 3-metre panel connection cable
J410 RPMP-11 control panel mounting platform kit including a 3-metre panel connection
cable but no control panel
J413 RPMP-21 control panel holder
Fieldbus K... Refer to ACS800 Ordering Information (EN code: 64556568).
I/O L...
Control program N...
Language of manual R...
Specialities P901 coated boards
Safety features Q950 Prevention of Unexpected Start, 500 mm (19.68 in.) cable outside the drive module in
frame size R7, 600 mm (23.62 in.) cable outside the drive module in frame size R8.

The ACS800-04/U4 and ACS800-04M
20
Main circuit and control interfaces
This diagram shows the control interfaces and the main circuit of the drive.
Motor
control and
I/O board
(RMIO)
External control via
analogue/digital
inputs and outputs
Optional module 1: RMBA, RAIO,
RDIO, RDNA, RLON, RIBA, RPBA,
RCAN, RCNA, RMBP, RETA, RRIA or
RTAC
Optional module 2: RTAC, RAIO, RRIA
or RDIO
DDCS communication option module:
RDCO-01, RDCO-02 or RDCO-03
Motor output
Brake chopper
(optional)
AC supply
Capacitor bank
Rectifier
R- UDC+ UDC-
R+
U1
V1
W1
U2
V2
W2
Inverter
Drive