Ablerex 625L User manual

This manual contains important safety instructions. Please follow all instructions carefully during
installation. Read this manual thoroughly before attempting to unpack, install or operate.
CAUTION
˙To prevent the risk of fire or electric shock, install in a temperature and humidity controlled
indoor area, free of conductive contaminants.
˙Risk of electric shock, do not remove the cover. No user serviceable parts. Refer servicing to
qualified service personnel.
˙Risk of electric shock, hazardous live parts inside this UPS can be energized from the battery
supply even when the inputAC power is disconnected.
˙Risk of electric shock, Battery Circuit is not isolated from AC input, hazardous voltage may
exist between battery terminals and ground. Test before touching.
NOTE：The UPS is designed to be used with computer loads only.
SETUP
Step 1：Inspection
Inspect the UPS upon receipt. Notify the carrier and dealer if
there is damage. The package is recyclable; save it for reuse or
dispose off properly.
Step 2：Placement
………………………………………………………………………………………………..
Step 3：Check the Site Wiring Fault Indicator (115V only)
Caution：If the site wiring fault indicator lights, get a qualified
electrician to correct the building wiring.
…………………………………………………………
Step 4：Connect the loads
First, connect the UPS with the AC Mains, then plug the loads
into the output connectors on the rear of the UPS. To use the
UPS as a master “On/Off” switch, make sure that all of the
loads are switch “On”.
Caution：Do not connect a laser printer
to the outlets. These UPS outlets provide
battery power and surge protection to the
equipment when utility voltage is outside
acceptable limits.
Ablerex
625L/1000L/1500L
625VA 1000VA /
1500VA
1000VA/ 1500VA
625VA
Step 5：Connect telephone / Network Surge protection
Connect a single line telephone or a 10 base-T / 100 base-T
network cable into the RJ-45 / RJ-11 telephone / network surge
protection “IN” jack on the back of the UPS. Connect from the
“OUT” jack with telephone cable or network cabling to a fax
modem or network port.
……………………………………………………………………………..…………………………
Step 6：Connect Computer Interface Port (Optional)
Connect the optional interface cable to the USB interface port
on the back of the UPS. Connect to the computer.
See software document for installation instruction.
……………………………………………………………
Step 7：Operation Test (forAblerex 625L)
a. Connect the UPS to the wall receptacle.
b. Push on the Main Switch to check the Green Line ( ) LED is on.
c. Connect your computer equipment with sockets of the UPS and pull off the input power cable of the
UPS from the wall receptacle to check if the Line ( ) LED is flashing every 3 seconds.
Meanwhile, please check if alarm buzzer is beeping.
d. Try the field working condition by running some application programs on your computer and
repeating step.
e. Check if the UPS is initiated properly to support continuous operation.
……………………………………………………………………………..…………………………
Step 8：Operation Test (forAblerex 1000L/1500L)
a. Connect the UPS to the wall receptacle.
b. Push on the Main Switch to check the Green Line ( ) LED is on.
c. Connect your computer equipment with sockets of the UPS and pull off the input power cable of the
UPS from the wall receptacle to check if the Line ( ) and Inverter ( ) LED are flashing every 2
seconds. Meanwhile, please check if alarm buzzer is beeping.
d. Try the field working condition by running some application programs on your computer and
repeating step.
e. Check if the UPS is initiated properly to support continuous operation.
IMPORTANT NOTE：Plug the UPS into the wall outlet to charge the UPS for over 8 hours before using.
FRONT PANEL EXPLANATION
ABLEREX 625L
1. Line LED( )：
˙Green LED remains standstill when Utility is normal.
˙Green LED flashes every 3 seconds and simultaneously buzzer alarms
continuously when Utility failure.
˙Green LED flashes every 3 seconds when the UPS is in Battery charging
Mode.
˙Green LED remains standstill and simultaneously buzzer alarms continuously when the UPS is in
overload condition.
1 3 2

2. Check Battery LED( )：
˙Red LED flashes every 0.5 seconds and buzzer alarms every 0.5 seconds when UPS is in battery
low condition.
3. Main Switch：
˙To Control on/off the UPS when Utility is normal.
˙To enable “DC-Start” Function when Utility fails. ( To enable DC Start properly, you are
recommended to connect <80% output load with the UPS only)
……………………………………………………………………………..…………………………
ABLEREX 1000L / 1500L
1. Line LED( )：
˙Green LED remains standstill when Utility is normal.
˙Green LED flashes every 2 seconds when the UPS is in Battery
charging mode.
˙Green LED remains standstill and simultaneously buzzer alarms
continuously when the UPS is in overload condition.
2. Inverter LED ( )：
˙Yellow LED flashes every 2 seconds and simultaneously buzzer alarms continuously when Utility
failure.
3. Overload LED ( )
˙Red LED remains standstill and simultaneously buzzer alarms continuously when the UPS is in
overload condition.
4. Check Battery LED ( )
˙Red LED flashes every 0.5 seconds and buzzer alarms every 0.5 seconds when UPS is in battery
low condition.
5. Main Switch：
˙To Control on/off the UPS when Utility is normal.
˙To enable “DC-Start” Function when Utility fails. (To enable DC Start properly, you are
recommended to connect <80% output load with the UPS only)
NOTE：Make sure the computer connected to the UPS is switched on before enable the "DC-Start"
function. You are not recommended to add some other computer or peripherals after DC-Start function
is activated. REAR PANEL EXPLANATION
1. AC Inlet ABLEREX 625L
2. Backup Outlets：3pcs NEMA5-15R or IEC320
3. USB Interface.
4. RJ11/RJ45 Jacks：MODEM /LAN Protection
5. Site Wiring Fault Indicator：For 115Vac system only.
6. AC Fuse Holder. (W/fuse)：625VA/115Vac/8A and
625VA/230Vac/6.5A
……………………………………………………………
1.ACInlet ABLEREX 1000L / 1500L
2. Backup Outlets：6pcs NEMA5-15R, Local socket or IEC320
3. Computer Interface：True RS232 communication port.
4. RJ11/RJ45 Jacks: MODEM /LAN Protection
5. Site Wiring Fault Indicator: For 115Vac system only.
6. USB Interface.
7. Fuse.
1 2 3 45
AC INPUT
IN OUTUSB
AC INPUT
IN OUTUSB
A
CINPUT
IN OUTUSB
REPLACING THE BATTERY
NOTE：Once the battery is disconnected, the loads are not protected from power outages.
ABLEREX 625L
Use a cross-type screwdriver to remove the two
front panel screws and slide down the panel.
ABLEREX 1000L / 1500L
Use a cross-type screwdriver to remove the two
top cover screws and slide back the cover. Please
refer to the figures STEP 1 through STEP 4.
1. Gently Pull the battery out of the UPS.
2. Loosen the black wire from the negative (-) terminal
and red wire from the positive (+) terminal.
3. Connect the battery leads to the new battery.
Note：Small sparks at the battery connectors are normal during connection.
4. Slide the battery into the UPS.
5. Close the front panel and fasten two screws.
6. Dispose of the old battery properly at an appropriate recycling facility.
TROUBLE SHOOTING
Situation Check Items Solution
Mains normal but 'Line' LED
is not on. 1. Is the power switch on? 2. Is the fuse in order?
3. Is the power cord loose?
1. Press Main Switch on.
2. Change fuse w/same rating.
3. Re-connect the power cord
properly.
'Line' LED flashes every
second but no output Battery voltage is too low Recharge the UPS for 24
hours.
Alarm buzzer beeps
continuously when Utility is
normal.
Check to see load status if it is
in overload. Remove some uncritical load.
Alarm buzzer beeps for 10
seconds, then the UPS is
turned off
Remove some uncritical load
and re-switch on the UPS.
No LEDs display on the front
panel Consult with your sales agent for help.
UPS dose not provide
expected back up time. 1. The UPS’s battery is weak due to recent outage.
2. The UPS’s battery is near
the end of its service life.
1. Charge the battery.
2. If the battery is near the end
of its service lift, consider
replacing the battery.
The UPS operates normally,
but the site wiring fault
indicator is lit.
Building wiring error such as
missing ground or hot to
neutral wire reversal.
Have a qualified electrician
correct the building wiring.
Automatic Shutdown Software can be downloaded at www.ablerex.com.sg
192321942013000
-