ABRITES TAG User manual

2021 Abrites TAG Key Tool User Manual
ABRITES DIAGNOSTICS
TAG KEY TOOL
User manual
version 2.4
www.abrites.comwww.abrites.com

www.abrites.com 2
2021
Important notes
Warranty
The Abrites software and hardware products are developed, designed and manufactured by Abrites Ltd.
During the production process we comply to all safety and quality regulations and standards, aiming at
highest production quality. The Abrites hardware and software products are designed to build a coherent
ecosystem, which effectively solves a wide range of vehicle-related tasks, such as:
Diagnostic scanning;
Key programming;
Module replacement,
ECU programming;
Configuration and coding.
All software and hardware products by Abrites Ltd. are copyrighted. Permission is granted to copy Abrites
software files for your own back-up purposes only. Should you wish to copy this manual or parts of it, you
are granted permission only in case it is used with Abrites products, has “Abrites Ltd.” written on all copies,
and is used for actions that comply to respective local law and regulations.
You, as a purchaser of Abrites hardware products, are entitled of a two-year warranty. If the hardware
product you have purchased has been properly connected, and used according to its respective instruc-
tions, it should function correctly. In case the product does not function as expected, you are able to
claim warranty within the stated terms. Abrites Ltd. is entitled to require evidence of the defect or mal-
function, upon which the decision to repair or substitute the product shall be made.
There are certain conditions, upon which the warranty cannot be applied. The warranty shall not apply to
damages and defects caused by natural disaster, misuse, improper use, unusual use, negligence, failure to
observe the instructions for use issued by Abrites, modifications of the device, repair works performed by
unauthorized persons. For example, when the damage of the hardware has occurred due to incompatible
electricity supply, mechanical or water damage, as well as fire, flood or thunder storm, the warranty does
not apply.
Each warranty claim is inspected individually by our team and the decision is based upon thorough case
consideration.
Read the full hardware warranty terms on our website.
Abrites TAG Key Tool User Manual

www.abrites.com 3
2021
Copyright information
Safety information
Copyright:
All material herein is Copyrighted ©2005-2021 Abrites, Ltd.
Abrites software, hardware, and firmware are also copyrighted
Users are given permission to copy any part of this manual provided that the copy is used with Abrites
products and the “Copyright © Abrites, Ltd.” statement remains on all copies
“Abrites” as used in this manual synonymous with “Abrites, Ltd.” And all it’s affiliates
The “Abrites” logo is a registered trademark of Abrites, Ltd.
Notices:
The information contained in this document is subject to change without prior notice. Abrites shall
not be held liable for technical/editorial errors, or omissions herein.
Warranties for Abrites products and services are set forth in the express written warranty statements
accompanying the product. Nothing herein should be construed as constituting any additional war-
ranty.
Abrites assumes no responsibility for any damage resulting from the use, misuse, or negligent use of
the hardware or any software application.
The Abrites products are to be used by trained and experienced users in diagnostics and reprogramming
of vehicles and equipment. The user is assumed to have a good understanding of vehicle electronic sys-
tems, as well as potential hazards while working around vehicles. There are numerous safety situations
that cannot be foreseen, thus we recommend that the user read and follow all safety messages in the
available manual, on all equipment they use, including vehicle manuals, as well as internal shop docu-
ments and operating procedures.
Some important points:
Block all wheels of the vehicle when testing. Be cautious when working around electricity.
Do not ignore the risk of shock from vehicle and building-level voltages.
Do not smoke, or allow sparks/flame near any part of the vehicle fuel system or batteries.
Always work in an adequately ventilated area, vehicle exhaust fumes should be directed towards the
exit of the shop.
Do not use this product where fuel, fuel vapours, or other combustibles could ignite.
In case any technical difficulties occur, please contact the
Abrites Support Team by email at [e-mail].
Abrites TAG Key Tool User Manual

Table of contents
www.abrites.com 4
2021 Abrites TAG Key Tool User Manual
1. Introduction .........................................................6
2. Getting Started ......................................................7
2.1 Scope of the manual .............................................7
2.2 Your transponder programmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.3 System requirements ............................................7
3. Getting Started ......................................................8
3.2 Connection of the PROTAG programmer to the interface . . . . . . . . 12
3.3 Starting of the software .........................................12
4. TagKey tool – working with different transponders . . . . . . . . . . . . . . . . . . . 14
5. TagKey tool – Key tool andpreparation of a key by
dump of immobilizer system.........................................15
6. TagKey tool – Production utility and preparation of a key
ready for programming by diagnostic equipment. . . . . . . . . . . . . . . . . . . . . . 18
7. TagKey tool – Cloning of a key .......................................19
7. 1. Offline ........................................................ 20
7. 2. Online .........................................................21
8. Porsche Panamera key by dump. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
9. CAS4 by dump......................................................32

www.abrites.com 5
2021 Abrites TAG Key Tool User Manual
List of revisions
Date Chapter Description Revision
01.10.2015
13.09.2017
23.08.2018
ALL
9
7
2.2
2.3
2.4
Total update of the manual. Cloning
added
CAS4 Key Preparation update
Added cloning of DST+ (G chip), M48
Fixed key and Temic 8C

www.abrites.com 6
2021 Abrites TAG Key Tool User Manual
1. Introduction
Congratulations for choosing our product!
PROTAG programmer together with the Abrites TagKeyTool software will allow you to use your Windows
based PC as a powerful programmer for transponders and tool for programming of transponder based
keys.
The PROTAG programmer is a hardware unit produced by Abrites Ltd. intended for programming of tran-
sponders via your AVDI interface. PROTAG programmer should be used with ABRITES software pro-
duced by Abrites Ltd.ABRITES is a trade mark of Abrites Ltd.

www.abrites.com 7
2021 Abrites TAG Key Tool User Manual
2. Getting Started
2.1 Scope of the manual
This document describes the software and hardware installation of your transponder programmer named
“PROTAG Programmer” and corresponding software named “Abrites Tag KeyTool”.
The document is applicable for the transponder programmers from Abrites Ltd. - ZN002.
2.2 Your transponder programmer
2.3 System requirements
Minimum system requirements – Windows Vista+, Pentium 4 with 512 MB RAM USB port with supply
100 mA / 5V +/- 5%

www.abrites.com 8
2021 Abrites TAG Key Tool User Manual
3. Getting Started
We suppose that your AVDI interface is configured and fully working. You can receive an optional sep-
arate installation file of your “Abrites Tag KeyTool” software for your AVDI and PROTAG programmer.
The software is a windows executable file named ‘SetupTagKeyTool_VVxxxx.exe’ where VVxxxx is your
interface identification number.
3.1 Software installation steps
Please start the executable file below to initiate the installation procedure and follow the onscreen
instructions.
Depending of your operation system and settings you can be asked to confirm starting of installation
procedure.
Press the “Next” button to proceed with the installation.

www.abrites.com 9
2021 Abrites TAG Key Tool User Manual
Read the license agreement and select “I accept the agreement” if you accepting all. Then press the “next”
button.
If you not agree press cancel to interrupt installation procedure.
Press the “Next” button to proceed with the installation.
Press the “Next” button to proceed with the installation.

www.abrites.com 10
2021 Abrites TAG Key Tool User Manual
Press the “Next” button to proceed.
If you do not want desktop icons uncheck the checkbox about creation of icons.
Press “Next” button to proceed.
Press “Install” and wait until installation complete.

www.abrites.com 11
2021 Abrites TAG Key Tool User Manual
Be sure that the checkbox about the installation of the interface’s USB drivers is set especially if you are
installing for the first time. Press “Finish”.
Depending on the setting of your operation system you can be asked to confirm installation of USB
drivers.
Press “Yes”.
Wait until the installation of USB driver finishes.

www.abrites.com 12
2021 Abrites TAG Key Tool User Manual
3.2 Connection of the PROTAG programmer to the interface
Once your AVDI interface is ready for work you can connect the PROTAG programmer to the PC through
one of the available USB ports of your PC.
3.3 Starting of the software
When the programmer is ready and connected to the PC you can start some of the applications from your
installation package. Each of these applications will notify you that the PROTAG programmer is found and
will use PROTAG programmer when it is needed.
If you are using TAG Key Tool application will appear following screen:
From the drop down list you can select some of needed transponders types or utilities which you needed.

www.abrites.com 13
2021 Abrites TAG Key Tool User Manual
You have also the ability to access additional EEPROM memory of the keys, to prepare a key ready for
starting of the vehicle using ‘Key Tool’, to prepare transponders ready for programming by diagnostic
equipment – ‘Production’ and also you can prepare a ‘cloning’ of a key using function ‘Key Cloner’.

www.abrites.com 14
2021 Abrites TAG Key Tool User Manual
Once an option is selected from the drop down list you will find a screen with options which allows you
to read and program the fields of the transponder.
The main buttons named “Read/Detect” and “Program” are intended to read and program the whole
memory of the transponder if that is possible.
Many types of transponders are read-only and the button “Program” is used to prepare a compatible tran-
sponder which can emulate the target transponder.
Bellow is the emulation list:
Megamos 13 can be emulated with T5 or PIT transponder.
Temic 11/12 can be emulated with T5.
Texas 4C can be emulated with TPX1 (available from version 5.2 of TagKey Tool) .
Texas 4D/4E can be emulated with TPX2.
HITAG-2 can be emulated with TPX3/TPX4 (available from version 5.2 of TagKey Tool) .
The small buttons “R” and “W” are intended to read or program only separate fields from the transponder
memory.
When working with transponder please be informed about corresponding transponder specification.
Many of the fields from transponder memory can be programmed only once.
It is very important to place the transponder when you read or program.
IMPORTANT:
Transponders or keys should be kept in the right place in the PROTAG programmer.
4. TagKey tool – working with different transponders

www.abrites.com 15
2021 Abrites TAG Key Tool User Manual
5. TagKey tool – Key tool andpreparation of a key by
dump of immobilizer system
“Key tool” is a utility intended for preparation of a key when a dump from immobilizer system of the
vehicle is present.
From the list of transponders and functions of the main screen you can select this utility.

www.abrites.com 16
2021 Abrites TAG Key Tool User Manual
Once you select the “Key tool” option a screen will appear with a drop down list where you can select
your model and immobilizer system.

www.abrites.com 17
2021 Abrites TAG Key Tool User Manual
In the list you can see the model, immobilizer module, type of memory where is stored key data and
needed transponder/key for programming.
When a model is select your next step should be to load the file containing the immobilizer data (dump).
You can load the dump
pressing button “Load Dump”.
You will have to to place then
your transponder/key in the
PROTAG programmer and
to press the button “Prepare
Key”.
Once the programming of the
transponder is finished, if it is
needed, you will be asked for
the file name of the modified
dump.
When a dump is loaded you should select the exact key position you want to program.
NOTE: Because different programmers can read from the immobilizer dump differently – NORMAL or
SWAPED, if after programming the transponder/key does not work, you will need to SWAP the dump and
load it back into the software and program a new key or transponder.

www.abrites.com 18
2021 Abrites TAG Key Tool User Manual
6. TagKey tool – Production utility and preparation
of a key ready for programming by diagnostic
equipment
“Production” is a utility intended for preparation of transponders ready for programming by diagnostic
equipment.
From the list of transponders and functions of the main screen you can select this utility.
From the screen “Production” utility you have to choose which type of transponder key you want to be
prepared. Then simply place your transponder/key on the PROTAG programmer and to press the button
“Program”.
When the programming of the transponder finishes, if it is needed, you will be asked for the file name of
the modified dump.
Information about the needed transponder is displayed.

www.abrites.com 19
2021 Abrites TAG Key Tool User Manual
The “Key cloner” function allows you to prepare a clone of some keys. Supported keys/transponders for
cloning currently are: Megamos 13, Temic 11, Temic 12, Toyota/Lexus/Scion Texas TIRIS 4D, all types of
ID33, Megamos 48 FIXED KEY, DST+ (G chip) and Temic 8C
When a key is placed in the PROTAG programmer press the button “Read/Detect”. The PROTAG pro-
grammer will read and identify the key and will then inform you what kind of transponder you need to
place in the programmer to prepare a cloned transponder.
If your PC is connected to the Internet, you’ve the ability to clone all kind of TIRIS 4D transponders, not
only Toyota/Lexus/Scion Texas 4D (ID67, ID68, ID70).
HITAG 2 transponders onto TPX3/ TPX4 cloning.
The Abrites PROTAG programmer now offers an easy cloning of HITAG 2 transponders onto TPX3 and
TPX4 transponders. This function requires Internet connection
7. TagKey tool – Cloning of a key

www.abrites.com 20
2021 Abrites TAG Key Tool User Manual
Cloning of 4D transponders
7. 1. Offline