Grizzly H6472 User manual

Introduction
The Model H6472 Shop Fox Classic Fence is made
exclusively for Grizzly Industrial by Woodstock
International to fit the Model G7209/G7210 14"
Table Saw. The Model H6472 is exactly the same
as the regular Shop Fox Classic fence, except
that the fence body, fence facing, and rails are
different.
How to Use this Sheet
This instruction sheet was designed to be used in
conjunction with the instruction manual provided
by Woodstock International, which is intended
for the regular Shop Fox Classic Fence (Model
W2005/W2006/W2007).
Because this is fence is produced only for Grizzly
Industrial, replacement parts exclusive to the
Model H6472 (shown to the right) are only avail-
able through Grizzly Industrial.
All other parts common to the Model W2005/
W2006/W2007 can be ordered through the
instruction manual included with your fence by
Woodstock International.
All instructions for the Model H6472 are the same
as the instructions for the Model W2005/W2006/
W2007, which are found in the instruction manual
included with your fence.
If you need additional help with assembly or
set up, we will be glad to help! Call our service
department at: [phone].
SHOP FOX® CLASSIC FENCE
MODEL H6472
MANUAL INSERT





COPYRIGHT © OCTOBER, 2004 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE
WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL.
#TR6708 PRINTED IN TAIWAN
8 PH6472008 FENCE BODY
8A PH6472008A FENCE FACING
10 PH64720010 REAR RAIL
10A PH64720010A FRONT RAIL SUPPORT
REF PART # DESCRIPTION
Parts Exclusive to H6472
(for all others refer to W2005 parts)

INSTRUCTION MANUAL
Phone: [phone] • On-Line Technical Support: [email protected]
COPYRIGHT © JANUARY 2000, REVISED MARCH 2004 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
Printed in Taiwan
MODELS
W2005, W2006, W2007
CLASSIC FENCE

CONTENTS
INTRODUCTION ............................................................................................ 2¦¦¦¦
General ........................................................................................................... 2
Warranty ......................................................................................................... 3
SAFETY PRECAUTIONS ................................................................................... 4
INSTALLATION ............................................................................................. 5
Inventory ........................................................................................................ 5
Rail Installation ................................................................................................ 6
Correcting Mounting Hole Misalignment ................................................................... 7
Magnetic Switch ................................................................................................ 8
7-Foot Rails ..................................................................................................... 9
Blade Guard ................................................................................................. 10
Fence .......................................................................................................... 10
ADJUSTMENTS ............................................................................................11
Fence Parallelism ............................................................................................ 11
Lock Handle .................................................................................................. 12
Fence-to-Table Clearance .................................................................................. 12
Scale and Cursor ............................................................................................. 13
OPERATIONS ..............................................................................................14
Using a Wood Fence Facing ................................................................................ 14
Using Board Buddies® ....................................................................................... 14
PARTS ......................................................................................................15
W2005 Fence Parts Diagram ................................................................................ 15
W2005 Standard Rail Parts Diagram ....................................................................... 16
W2007 Leg and 7' Rail Parts Diagram ..................................................................... 17
W2005 Parts List .............................................................................................. 18
W2007 Parts List .............................................................................................. 18

-2- Shop Fox® Classic Fence
Thank you for purchasing Woodstock
International’s SHOP FOX® Classic Fence.
This fence is classic in its design and function,
and provides a perfect upgrade for table saw
owners who expect precision and ease of
installation. It has been designed to fit almost
all contractor and cabinet-style table saws and
is easy to install.
The SHOP FOX® Fence features include:
• Wide T-shape style design for maximum
accuracy and support.
• Single locking action cam lever.
• Simple mounting procedure, easy lift off
design for the fence makes using jigs and
fixtures simple.
• HDPE high durability plastic fence surface
provides low sliding resistance.
• Fence can be used on either the right or
left side of the blade.
• Magnified cursor can be mounted on
either side of the fence.
• Fence body has powder coated paint
surface for durability.
• Standard rails provide 25" maximum rip to
the right of the blade (W2005).
• Optional long rails provide 54" maximum
rip to the right of the blade (W2006).
Woodstock is pleased to provide this manual
to assist in the installation and operation of
the SHOP FOX® Classic Fence. It represents
our effort to offer the finest documentation
available. If you feel there are areas where this
manual could be improved, we encourage you
to write us with your comments at the following
address:
Technical Documentation
Woodstock International, Inc.
P.O. Box 2309
Bellingham, WA 98227
Tel: [phone]
Fax: [phone]
This fence was specifically designed to
be used on table saws to assist in cutting
operations. DO NOT MODIFY AND/OR USE
THIS FENCE FOR ANY OTHER PURPOSE.
Modifications or improper use of this device
will void the warranty. If you are confused
about any aspect of this accessory, DO NOT
use it until all your questions have been
answered. Serious injury may occur.
General
INTRODUCTION

Shop Fox® Classic Fence -3-
Woodstock International, Inc. (Woodstock)
warrants this product against defects in
workmanship and materials under normal use
and service for a period of one year. This
warranty extends to the original purchaser from
the date of purchase. This warranty does not
apply to defects due directly or indirectly to
misuse, abuse, negligence, accidents, repairs
or alterations or lack of maintenance.
This is Woodstock’s sole written warranty and
any and all warranties that may be implied by
law, including any merchantability or fitness,
for any particular purpose, are hereby limited
to the duration of this written warranty. We do
not warrant or represent that the merchandise
complies with the provisions of any law or acts.
In no event shall Woodstock’s liability under
this warranty exceed the purchase price paid
for the product and any legal actions brought
against Woodstock shall be tried in the State of
Washington, County of Whatcom.
We shall in no event be liable for death,
injuries to persons or property or for incidental,
contingent, special or consequential damages
arising from the use of our products.
To take advantage of this warranty, the product
or part must be returned to the original place
of purchase. Proof of purchase must accompany
the merchandise. Woodstock reserves the right
to change specifications at any time since we
constantly strive to achieve better quality
equipment.
We make every effort to ensure that our
products meet high quality and durability
standards and we hope you never need to use
this warranty.
Warranty

-4- Shop Fox® Classic Fence
12. USE A PUSH STICK WHEN CUTTING
NARROW PIECES.
13. DO NOT REACH BEHIND TABLE SAW
TO GRAB CUTOFF PIECE. If wood binds
against saw blade it will kick back faster
than you can let go.
14. DO NOT LET THE END OF THE
WORKPIECE CONTACT THE FENCE WHILE
CROSSCUTTING WOOD WITH THE MITER
GAUGE. There is a potential for kick-back.
Move the fence away.
15. DISCONNECT TABLE SAW FROM POWER
before servicing and when changing
accessories, such as blades, bits, and
cutters.
16. AVOID ACCIDENTAL STARTING. Make sure
the switch is in the “OFF” position before
plugging in the cord.
17. CHECK DAMAGED PARTS. Do not operate
the table saw until you are certain it is in
perfect running condition.
18. NEVER LEAVE THE TABLE SAW RUNNING
UNATTENDED - TURN POWER OFF. Do not
leave the saw until it comes to a full stop.
19. DO NOT OPERATE EQUIPMENT IF USING
DRUGS, ALCOHOL, OR MEDICATION.
20. DO NOT OPERATE EQUIPMENT if you are
mentally or physically fatigued.
21. IF THERE IS SOMETHING YOU DO NOT
UNDERSTAND, DO NOT OPERATE
MACHINE! Ask for help first.
22. BAD HABITS ARE DANGEROUS. Review all
safety procedures often.
1. KNOW YOUR TABLE SAW. Read the
owner’s manual carefully. Learn the tool’s
applications and limitations, as well as its
particular hazards.
2. DO NOT REMOVE GUARDS. Maintain
guards in working order.
3. ENSURE THAT YOUR TABLE SAW IS
ELECTRICALLY GROUNDED. Never remove
the grounding prong.
4. KEEP WORK AREA CLEAN. Cluttered areas
invite accidents.
5. AVOID DANGEROUS ENVIRONMENTS.
Do not use power tools in damp or wet
locations or expose them to rain. Keep
your work area well lighted.
6. MAKE WORKSHOP CHILD-PROOF with
padlocks, master switches, or by removing
starter keys.
7. DO NOT FORCE WORK THROUGH TABLE
SAW. Tools work better and more safely
when they are allowed to work at their
own speed.
8. WEAR PROPER APPAREL. Do not wear
loose clothing, gloves, neckties, or jewelry
that might get caught in moving parts.
Non-slip footwear should be worn. Tie
back long hair.
9. NEVER STAND OR LEAN ON TOOL.
10. ALWAYS USE SAFETY GLASSES, EAR
PROTECTION AND RESPIRATORY
PROTECTION.
11. DO NOT OVERREACH. Keep proper footing
and balance at all times.
These safety rules cannot cover every situation in a woodshop. Consider your conditions when
setting up and using your SHOP FOX® Classic Fence.
SAFETY PRECAUTIONS

Shop Fox® Classic Fence -5-
Inventory
Installation of the SHOP FOX® Classic Fence
involves mounting the front and back rails to
your table saw, setting the fence on the rails
and doing a simple alignment. First check the
contents of the package:
Model W2005
Fence Assembly .............................. 1
Back Rail ..................................... 1
Front Rail ..................................... 1
Front Rail Rectangular Tube ............... 1
Scale ........................................... 1
Drill and Tap ................................. 1
Blade Guard Clamp Bag
• V-Clamp .................................. 1
• L-Bracket ................................. 1
• Locking Plate ............................ 1
• Hex Bolt 1⁄4-20 X 11⁄2" ................. 2
• Flat Washer 1⁄4" ......................... 4
• Hex Nut 1⁄4-20 ........................... 2
• Hex Bolt 5⁄16-18 X 3⁄4" ................. 1
• Flat Washer 5⁄16" ....................... 2
• Hex Nut 5⁄16-18 .......................... 1
Rail Mounting Bags
• Hex Bolt 1⁄4-20 X 3⁄4" ................... 4
• Hex Bolt 3⁄8-16 X 1" ..................... 4
• Flat Hd Scr 1⁄4-20 X 3⁄4" ................. 2
• Flat Washer 1⁄4" ........................10
• Flat Washer 3⁄8" ......................... 8
• Hex Nut 1⁄4-20 ............................. 2
• Hex Bolt M10-1.5 X 25 ................. 4
Model W2006
Fence Assembly .............................. 1
All other components are the same as the
Model W2007.
INSTALLATION
Model W2007
Back Rail 7' ................................... 1
Front Rail 7' ................................... 1
Front Rail Rectangular Tube 7' ............ 1
Scale ........................................... 1
Drill and Tap ................................. 1
Blade Guard Clamp Bag
• V-Clamp .................................. 1
• L-Bracket ................................. 1
• Locking Plate ............................ 1
• Hex Bolt 1⁄4-20 X 11⁄2" ................. 2
• Flat Washer 1⁄4" ......................... 4
• Hex Nut 1⁄4-20 ........................... 2
• Hex Bolt 5⁄16-18 X 3⁄4" ................. 1
• Flat Washer 5⁄16" ....................... 2
• Hex Nut 5⁄16-18 .......................... 1
Rail Mounting Bags
• Hex Bolt 1⁄4-20 X 3⁄4" ................... 4
• Hex Bolt 3⁄8-16 X 1" ..................... 4
• Flat Hd Scr 1⁄4-20 X 3⁄4" ................. 2
• Flat Washer 1⁄4" ........................10
• Flat Washer 3⁄8" ......................... 8
• Hex Nut 1⁄4-20 ............................. 2
• Hex Bolt M10-1.5 X 25 ................. 4
Legs ........................................... 2
Support Bracket .............................. 2
Feet ............................................ 2
Leg Mounting Bag
• Hex Nut 1⁄2-12 ............................. 2
• Flat Washer 3⁄8" ......................... 8
• Hex Bolt 1⁄4-20 X 1⁄2" .................. 4
• Flat Washer 1⁄4" ......................... 4
• Hex Bolt 3⁄8-16 X 5⁄8" ................... 2
Note—Extra mounting hardware has been included
to compensate for differences between table
saws. You may not need all of the hardware that
is included in the inventory.

-6- Shop Fox® Classic Fence
Figure 2. Mounting the front and back rails.
3. Position the back rail so its top edge
is flush with the table top and the
rectangular cut-outs are in line with the
miter slots. See Figure 1.
UNPLUG the saw power cord, and TURN
OFF the power switch before you begin
fence installation procedures. Accidental
saw startup while installing or adjusting the
fence will result in serious personal injury.
Rail Installation
On most saws, the mounting holes for the rails
will match the existing rail mounting holes.
On the saws where the mounting holes do
not line up, see Correcting Mounting Hole
Misalignment on Page 14 for instructions on
drilling new holes.
Metric and standard hex bolts have been
included to fit most common rail installations.
Mounting the Back Rail
1. Remove the mounting hardware for the
blade guard which extends over the back
edge of the table. (Be sure to reinstall the
guard after completion.)
2. Locate the back fence rail (the rail with
the two rectangular cut-outs on one edge
and one cutout on the other edge) and set
it against the rear edge of the table saw.
Figure 1. Attaching the back rail.
4. Attach the rail using the mounting
hardware from the old rail or two 3⁄8"-16
x 1" or M10-1.5 X 25 hex head bolts and
washers. Secure as shown in Figure 2.

Shop Fox® Classic Fence -7-
Mounting The Front Rail
1. Align the side of the front rail with two
rectangular cutouts against the edge of the
table.
2. Set the top edge of the front rail so it is
flush with the table top and the cutouts
are in line with the miter slots. If your saw
table has a beveled front edge, then align
the top of the rail with the bottom edge of
the bevel. See Figure 3.
Figure 3. Attaching the front rail bracket.
Bottom Edge
of Bevel
3. Attach the rail using the mounting
hardware from the old rail or two 3⁄8"-16
x 1" or M10-1.5 X 25 hex head bolts and
washers. Secure as shown in Figure 2.
Figure 4. Shimming the front tube.
Mounting The Front Rail Tube
1. Orient the machined flat edge of the tube
so it faces the table edge.
2. Thread four 1⁄4-20 X 3⁄4" hex bolts and
1⁄4" washers through the rail and into the
threaded holes in the bottom of the tube.
3. If your table has a beveled front edge,
it may be necessary to install spacers or
shims between the rail and the rectangular
tube as shown in Figure 4. The spacers
should equal approximately the height of
the bevel (3⁄8" on most saws). Four to six
washers installed with each of the four
attachment screws should raise the height
of the tube enough to assure clearance of
the fence above the table surface.
4. Mount the fence on the rails and check the
clearance between the bottom edge of the
HDPE facing and the table top.
5. Add or remove shims from the tube to
rail mounting until a clearance of at least
1⁄16" is achieved. Note—This clearance
should never exceed 1⁄8", as this can allow
material to get under the fence during
certain types of sawing operations.
Note: Do not install the scale at this time.