AC Infinity CLOUDLINE Series User manual

USER MANUALUSER MANUAL
CLOUDLINE
MIXED FLOW DUCT FAN SYSTEMS

3
WELCOME
Thank you for choosing AC Infinity. We are committed to product quality and friendly customer service.
If you have any questions or suggestions, please don’t hesitate to contact us. Visit www.acinfinity.com
and click contact for our contact information.
EMAIL
[e-mail]
WEB
www.acinfinity.com
LOCATION
Los Angeles, CA

4
PRODUCT
CLOUDLINE S4
CLOUDLINE S6
CLOUDLINE S8
CLOUDLINE S10
CLOUDLINE S12
CLOUDLINE T4
CLOUDLINE T6
CLOUDLINE T8
CLOUDLINE T10
CLOUDLINE T12
MODEL
AI-CLS4
AI-CLS6
AI-CLS8
AI-CLS10
AI-CLS12
AI-CLT4
AI-CLT6
AI-CLT8
AI-CLT10
AI-CLT12
UPC-A
819137020290
819137020306
819137020849
819137020856
819137021006
854759004785
854759004792
819137020276
819137020283
819137021013
MANUAL CODE CL1910X1
EC models CANNOT be daisy chained with DC models. See page 19 & 20 for
more information on daisy-chaining fans and safety precautions.

5
MANUAL INDEX
Manual Index .................................................................................
Key Features .................................................................................
Product Contents ...........................................................................
Installation (Mounting) ...................................................................
Installation (Configuration Setup) ..................................................
Powering ........................................................................................
Programming .................................................................................
Other AC Infinity Products .............................................................
Warranty ........................................................................................
Page 5
Page 6
Page 7
Page 9
Page14
Page 16
Page 25
Page 33
Page 34

6
KEY FEATURES
SMART CONTROLLER
Controls and monitors temp.
and humidity using included
probe. Also features high
temp. triggers and alarms.
QUIET PWM MOTOR
PWM-controlled motor features
precise speed control, reduced
rotor noise, and energy-efficient
DC voltage.
IP-44 PROTECTION
The inline duct fan is sealed
to Ingress Protection 44
standards, rated with high
resistance to liquids and dust.
STATOR BLADE FANS
Hydro-mechanical stator
blades enable efficient airflow
delivery in high static pressure
environments.
SPEED CONTROLLER
Single button controller with
circular readout display that
enables fan speed control in
eight speeds.
DUAL BALL BEARINGS
The motor contains ball bearings
with an estimated 67,000 hour
lifespan. Enables the fan to be
mounted in any direction.

7
PRODUCT CONTENTS
CLOUDLINE S-Series
SMART
CONTROLLER
(x1)
SENSOR
PROBE
(x1)
DUCT FAN
SYSTEM
(x1)
DUCT
CLAMP
(x2)
DUCT FAN
SYSTEM
(x1)
WALL
ANCHOR
(x4)
WIRE
TIE
(x6)
CABLE TIE
MOUNT
(x6)
DUCT FAN
SCREW SET
(x4)
CLOUDLINE T-Series
CLOUDLINE S-Series/T-Series (Included in Both Series)
CONTROLLER
SCREW SET
(x2)
WOOD
SCREWS
(x2)
MACHINE
SCREWS
(x2)
CONTROLLER
SCREW SET
(x2)
WOOD
SCREWS
(x6)

8
PRODUCT CONTENTS

9
INSTALLATION
STEP 2
Remove the motor box from the flange bracket.
Remove the wind circle between the motor box
and the intake flange.
STEP 1
Unscrew and loosen the metal rings using a
Phillips screwdriver and pliers.
MOUNTING

10
INSTALLATION
STEP 3
Use the flange bracket to set your desired fan
position. Mark the four mounting holes.
STEP 4
Drill four holes into the marked locations. Make
sure your mounting area is structurally sound
and free from obstruction.
MOUNTING

11
STEP 5
If you are mounting onto anything other than a
wood support or stud, insert the included four
wall anchors into the drilled mounting holes.
You may need to use a hammer to secure them
through the holes.
INSTALLATION
STEP 6
Align the flange bracket’s holes with the wall
anchors. Screw in four wood screws with a
screwdriver or drill to secure the flange bracket.
Make sure its airflow arrow is pointing in your
desired direction.
MOUNTING

12
INSTALLATION
STEP 8
Slide the motor box back into the flange
bracket, making sure its airflow arrow is pointing
in the same direction as the flange bracket’s
arrow. Tighten the metal clamps using a Phillips
screwdriver and pliers to secure the motor box.
STEP 7
Place the wind circle back into the intake flange
and reposition the metal clamps over the
flanges if applicable.
MOUNTING

13
STEP 9
Place the metal rings back onto the flanges and
tighten the screws back to secure the fan.
STEP 10
If installing ducting, use the included duct
clamps to secure it to either end of the duct fan,
making sure there is a tight seal. Tighten the
duct clamps using a flathead screwdriver.
INSTALLATION
MOUNTING

14
INSTALLATION
STEP 11(b) - Hanging Downward
You may also hang the fan by looping the rope
hangers around its mounting plate. Tighten the
rope to secure the fan.
Make sure the fan’s airflow arrow is pointing
towards your desired direction.
STEP 11(a) - Hanging Upward
If installing with rope hangers (sold separately),
loop the ropes around the flanges and tighten
the rope to secure the fan.
CONFIGURATION SET-UP

15
Intake and Exhaust
This fan can be used as either an intake fan or an exhaust fan in grow rooms and larger grow tents.
To achieve optimal whole space ventilation, the intake fan or opening - if not using a fan - must be
situated at a bottom corner of your grow space. The exhaust fan must be hung (shown below) or
mounted at the highest opposite corner possible.
Make sure the intake fan’s airflow arrow is pointing towards your grow space and the exhaust fan’s
arrow pointing away from your grow space.
INSTALLATION
CONFIGURATION SET-UP

16
POWERING AND SETUP
STEP 2
Lastly, to power both the fan and controller, plug
the fans power cord into an AC power outlet.
(For EC Motor fans only)
STEP 1
Plug the duct fan’s 4-pin molex connector into
the speed controller’s port at the top.
S-SERIES

17
POWERING AND SETUP
STEP 2
Plug the duct fan’s 4-pin molex connector into
the universal controller’s left port signified by
the fan/power symbol.
STEP 1
You may cable manage the cords using tie
mounts, wood screws, and zip ties included
with this fan.
Secure the tie mounts onto a surface using
the wood screws. Loop the zip ties around the
cords into the tie mounts.
T-SERIES

18
STEP 3
Plug the sensor probe into the controller’s
3.5mm jack. Set the probe near your plants in
your grow tent for the most accurate reading.
STEP 4
Lastly, to power both the fan and controller, plug
the fans power cord into an AC power outlet.
(For EC Motor fans only)
POWERING AND SETUP
T-SERIES

19
DC/EC Motors
To find out your fan's motor type, look at its power cord(s). DC-motor CLOUDLINE fans have one
female molex connector cord and include an AC adapter that must be plugged into the controller
and an outlet. EC-motor CLOUDLINE fans have two cords, featuring a molex connector and a
three-pronged power plug that directly connects to an outlet.
ADDING MORE FANS
DO NOT connect a DC-motor fan with an EC-motor fan! Daisy
chaining these fans together will cause electrical damage.
EC models have two cords with a molex
connector and a three-pronged plug.
DC models have one cord with a molex
connector and include an AC adapter.
EC MOTORDC MOTOR
EC MOTORDC MOTOR

20
T-SERIES CONTROLLER
Smart controllers for T-Series models with DC motors can support two fans of the same tier model.
For example, the CLOUDLINE T4 can only support an S4 fan, the CLOUDLINE T6 can only
support an S6 fan and so on.
Smart controllers for T-Series models with EC motors can support two fans of any size. The two
EC-motor fans must be plugged in to an outlet to power the fans and the controller. See images
below.
ADDING MORE FANS
The smart controller for the CLOUDLINE T-Series
has an additional port so that you can add an
S-Series fan to power and control two fans together.
Please see below for limitations.
EC MOTORDC MOTOR
T6//S6
T4//S4T4//S4 T4//S4