AccuBANKER LED430 User manual

LED430 / LED420
Cash + Card Detector

Thank you for purchasing this AccuBANKER product.
We recommend reading all information in the user guide to
become familiar with this product.
Cash Handling Security

Important Safety Instructions
This device has been designed to operate with this specic Power Supply (AC / DC •
Adapter which is included. Failing to do so may cause malfunction and may void it’s
warranty.
Avoid looking directly the super-bright Ultraviolet LEDs hidden inside the unit. •
Avoid operating the unit close to strong natural/articial light source. The effect of •
the UV light will be overpowered and it will affect the UV feature’s uorescence.
Unplug this product from the wall outlet and refer servicing to qualied • service per-
sonnel under the following conditions:
When the power supply cord or power adapter is damaged.1.
If liquid has been spilled into the unit.2.
If the unit does not operate normally by following the operating instructions.3.
If the the product has been dropped or the case has been damaged.4.
If the product shows a noticeable change in performance.5.

4
Accurate and convenient to use, the LED420 / LED430 detectors allow the user to
inspect either money, Credit Cards, ID’s or any security document and verify and
conrm its authenticity.
1. Before Starting
This User Guide will allow you to get familiar with all the details related with the
unit’s operation. We recommend reading this guide thoroughly before operating the
unit and keep it for future references.
Introduction

5
2. Parts Description
10
1- Power On / Off indicator
2- Magnier window (only for LED430)
3- UV / WM Selector Buttons
(Ultraviolet / Watermark)
4- Verication Window / Watermark
Screen.
5- Magnetic Head (only for LED430)
6- Function Activator Sensor
7- Security Thread Identication
Label
8- Power Switch
9- Power Adapter Jack
10- Power Adapter (12VDC)
2
3
4
5
6
7
1
0
8
9

6
3. Operation Description
We recommend the users to familiarize themselves with the security features of the bills
or documents they want to analyze in order to use the unit appropriately and efciently.
Additionally, we recommend the users to compare any dubious banknote against a good
one, to better determine if it is authentic or not.
This is a DC powered device and includes a power adapter for this purpose. Proceed
to connect the power adapter to the power outlet on the wall and the DC plug into the
device power adapter jack, then proceed to turn the device ON using the power switch
located at the device’s back.
3.1 Ultraviolet Verication Operation
Place the bill or document to analyze on the WM verication window trying to activate
the activator sensor with the own bill or document meanwhile it is being positioned on
the inspection area. In case the activator sensor doesn’t get active, you can tap the UV
control button to turn the UV leds ON manually. The detector has an internal timer that
keeps the UV leds on for about 50 sec. before turning them off. You can tap the UV but-
ton again in case you require more time to nish the verication.

7
Ultraviolet Verication Operation (cont.)
The UV security features embedded in U.S dollar bills, foreign currencies, Credit Cards,
ID’s and other special documents will uoresce under the UV light and the user will be
able to visualize them and conrm their authenticity.
NOTE: The detector includes a “Security Thread Identication” label that shows the
operator the COLOR and POSITION of the security thread embedded on the U.S dollar
bills for every specic denomination. Using it as reference will help the operator to vali-
date them since the COLOR and POSITION must match.
3. Operation Description

8
3.2 Watermark Verication Operation
Press the WM function button to turn the WM screen ON, the entire inspection area will
be illuminated to make bill’s analysis procedure easier and faster. Proceed to verify the
watermark features embedded in the bill or document and conrm their authenticity. The
absence, displacement, or low quality of this feature will indicate the bill is not genuine.
The internal timer will keep the WM ON for about 50 sec., in case you require more time,
just press the WM button again.
3.3 Magnetic Verication Operation (only for LED430 model)
Once the detector is turned ON, the magnetic circuitry is already active and remains so
while the unit is ON.
Proceed to rub the area of the bill that must contain magnetic ink against the magnetic
head. If the verication window ash in GREEN color and at the same time a BEEPING
sound is emitted, it conrms the Magnetic ink feature is present on the area just veried.
In case none of these signs are present, means there is not MG ink in the scanned area.
3. Operation Description

9
3. Operation Description
Place the bill or document under the magnier window and proceed to inspect visually
the micro-printing elements and ne lines security features embedded in the bill or docu-
ment. Any low quality printing is a suspicious sign that must be considered during the
nal decision.
3.5 Size Analysis
The detector has a millimetric scale printed on the verication window that allows the
user to verify any specic bill or document size as well as to validate the right position of
any security feature inside the bill or document. Any displacement encountered on any
security feature could be a suspicious sign and other features must be veried to conrm
the bill or document authenticity.
NOTE: Avoid operating the unit close to strong natural/articial light source. The effect of
the UV light as well as the Watermark light will be overpowered and it will affect the good
visualization and analysis of the security features embedded on the bill or document.
3.4 Micro-Printing Magnier (only for LED430 model)

10
The user has the option to customize the UV light intensity of the detector based on his
specic needs. Press the UV button to turn the UV ON, then keep pressed down the UV
or WM button to increase or reduce the UV leds light intensity. The new light intensity will
be used from now on until the user decide to change it again using this same procedure.
4. UV Light Intensity Adjustment
Increase
Intensity
Reduce
Intensity
WM UV
5. Cleaning and Maintenance
- Keep the activator sensor and the verication window
clean of dust or any other type of dirtiness, use a dry
cloth for this.
- Keep the MG head and Magnier clean, use a dry
cloth for this (for LED430 model).
NOTE: Be careful with the UV LEDs located inside
on the upper section, do not hit them by mistake.
UV
LEDs