Accuride ST8200 User manual

0.95
[24.1]
3.06
[77.6]
0.07
[1.8]
1
1 0
NS F
1.30
[33.0] C
D
E
F
G
Ø.20 [5.0]
TYPICAL
Ø.20 [5.0] B
.95
[24.1]
3.06
[77.6]
Ø.19 [4.9]
TYPICAL
.583
[14.81]
REF.
Ø.20 [5.0]
TYPICAL
.07
[1.8]
A
1.53
[38.8]
DRAWER MEMBER IS
FLUSH OR UNDER IN
CLOSED POSITION
SLIDE TRAVEL SLIDE LENGTH
B
.50
[12.7]
LEVER DISCONNECT
FOR DRAWER MEMBER
MODEL ST8200
Up to 275 lbs. [124.73 kg] Capacity*
Side-Mount
APPLICATIONS: Designed for use in heated and refrigerated
drawers and prep tables in food service that require routine
cleaning and disassembly. NSF-certified.
Inches
[mm]
Part Number Slide Length Slide Travel A B C D E F G
8200-16 15.75 [400] 15.24 [387] 15.75 [400] 7.36 [187] 5.04 [128]  8.11 [206] 13.15 [334]
8200-18 17.72 [450] 17.20 [437] 17.72 [450] 8.35 [212] 5.04 [128] 10.08 [256] 15.12 [384]
8200-20 19.69 [500] 19.17 [487] 19.69 [500] 9.33 [237] 4.76 [121] 8.54 [217] 12.32 [313] 17.09 [434]
8200-22 21.65 [550] 21.14 [537] 21.65 [550] 10.31 [262] 4.76 [121] 9.53 [242] 14.29 [363] 19.06 [484]
8200-24 23.62 [600] 23.11 [587] 23.62 [600] 11.30 [287] 5.75 [146] 10.51 [267] 15.28 [388] 21.02 [534]
8200-26 25.59 [650] 25.08 [637] 25.59 [650] 12.28 [312] 5.75 [146] 11.50 [292] 17.24 [438] 22.99 [584]
8200-28 27.56 [700] 27.05 [687] 27.56 [700] 13.27 [337] 5.00 [127] 10.00 [254] 14.96 [380] 19.96 [507] 24.96 [634]
8200-30 29.53 [750] 29.02 [737] 29.53 [750] 14.25 [362] 5.00 [127] 10.63 [270] 16.30 [414] 21.93 [557] 26.93 [684]
Progressive Movement
Self-closing action, adjustable tilt-angle, auto-
relock, NSF-certified and dishwasher-safe
Up to 275 lbs.
300,000 cycles (Tested on 18" slides in a 30"
wide drawer at gross load of 125 lbs.).
400lb (Tested at full extension for 24 hours)
-4°F to + 176°F
[-20°C to + 80°C]
Movement
Features
Load Rating
Cycle Rating
Static Load
Operating
Temperature
Range
Stainless Steel (441)
Even lengths 16" - 30" [400 mm - 750 mm]
Full Extension
3.06" [77.6 mm]
.95" + .060"/-.020" [24.13 + 1.52/-.51]
Side-Mount
#8 flat and #10 hex (not included)
Material
Lengths
Travel
Height
Side Space
Mounting
Hardware

2
Before starting the installation process, the slides must be
disassembled into the individual three members. Extend the slide
members and follow the steps as shown in Figure 5. Remove the
intermediate member and then follow steps shown on Figures 11
and 12 to remove the intermediate member.
Drawer Member Mounting
To install the drawer member, use #8 undercut flathead screws.
The use of all the mounting holes is recommended to ensure
maximum load capacity. It is recommended to mount near the
center line of the drawer. See Figure 1.
Mounting Instructions
Figure 4
Drawer Front
Figure 1
Cabinet Member Mounting
Align the cabinet member (outer member) at the proper height so
that the drawer can be inserted with no interference. Install the
cabinet member using #10 hex screws, and ensure slides are
parellel. See Figure 2.
Screw 2
Screw 3
Screw 1
Cabinet
Front
Instop
Cabinet
Figure 2
To modify angle, remove screws 1 and 3 and rotate around
screw 2 to desired angle and reinstall, as shown in Figure 3.
Figure 3
Intermediate Member Insertion
Insert intermediate member into the installed cabinet member,
as shown in Figure 4.
Flat (0°) Mounting 2° Back Angle 4° Back Angle
Drawer Insertion
Before starting drawer insertion, ensure the following:
• Intermediate member should be nested inside cabinet member
(outer member).
• Extend intermediate member and pull the locking lever as
shown in Figure 5.
Pull
Figure 5
• Press down on the locking lever as shown in Figure 6.
If it moves freely, it is unlocked.
WARNING: Locking lever must be unlocked to insert drawer.
Figure 6
Angles may vary by slide length

3
Figure 7
Once lever is unlocked, drawer insertion can begin. The drawer
begins by riding over the rollers (Figure 7), then lifts past the stop
to engage with the middle rollers (Figure 8). The drawer then
stabilizes into the horizontal position (Figure 9).
Figure 8
Figure 9
NOTE: Upon drawer closure, drawer will automatically lock.
Drawer Removal
To remove drawer, fully extend unit, then unlock the locking lever
by pulling (see Figure 10). Then lift out drawer and remove.
Pull
Figure 10
WARNING: Locking lever must be unlocked to remove drawer.
Intermediate Member Removal
Lift latch tab and pull (as shown on Figures 11 and 12).
Figure 11
Pull
Figure 12
Mounting Instructions (continued)

Copyright © 2021 Accuride International Inc. 3700-9598 (1281)-MK200-R2-0421
Customer Supplied Hardware
Slide Ordering Instructions
Complete your order for Accuride Model ST8200 by specifying
the following:
20 pr ST 8200-XX D
Total Required Slides
Slide Material
Slide Model
Slide Length
Packaging
Packaging Information
Distributor (D) Pack: Box quantities vary by length (hardware
not included), one pair of slides packaged in a polybag with a
technical sheet.
Slide lengths 16"-22" 8 slides per box
24"-30" 4 slides per box
Bulk (P) Packaging: Quantities vary by length, slides only
(hardware not included). Left and right hand slides packaged
in separate boxes.
Slide lengths 16"-22" 8 slides per box
24"-30" 4 slides per box
To order bulk pack specify ST8200-28-L for the left hand and
ST8200-28-R for the right hand.
Specifications
Slide Members: 441 Stainless Steel
Rollers: Dupont™ Delrin® 100
NSF-certified
RoHS compliant
NOTE: Specifications, materials, prices, terms and delivery
are subject to change without notice.
4
For the most current technical information visit www.accuride.com
Accuride International Inc.
12311 Shoemaker Avenue
Santa Fe Springs, CA 90670
TEL [phone]
FAX [phone]
Manufacturing, Engineering, and Sales
United States • Germany • Japan •
Mexico • United Kingdom • China
WARNING: This product can expose you to chemicals including nickel,
which is known to the State of California to cause cancer and birth defects or
other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Drawer Member: #8 undercut flathead screws
Cabinet Member: #10 hex-head screws