Accusplit AE1640M4 User manual

SETTING UPYOUR PEDOMETER
To record your distance and calories accurately, you will
need to set your stride length.
CHOOSING A MEASUREMENT SYSTEM
This unit is initially set to use English measurement units
(Miles). To change the unit back and forth between English
and Metric units (Kilometers), press the green RESET button
for 5 seconds.
Finding Your Stride Length: Your stride length is the length of
one of your steps, measured from “toe to toe.”To measure,
walk 10 steps with your normal stride and measure the
TOTAL DISTANCE from the toe of your starting step to the
toe of your 10th step (see diagram below). Divide theTOTAL
DISTANCE by 10.This is your stride length. Example: If you
walk 22 feet, your stride length is 2.2 feet.
SettingYour Stride Length: Press the yellow MODE button
until arrow on bottom of display points to “DIST.” Press the
dark blue SET button once to enter setting mode. Display will
shift to show stride (for example, “F 1.95” means stride is set
to 1.95 feet). Press the dark blue SET button to increase stride
length. Press the green RESET button to reduce stride length.
Press the yellow MODE button to exit setting mode.
WEARING YOUR PEDOMETER
While gently holding the belt clip open, slide the pedometer
onto your belt or the top edge of your pants or skirt. It
should fit snugly and level, above one knee.
Note: The pedometer should be as vertical as possible.
Walkers with larger stomachs may find it helpful to wear the
pedometer farther back on the body, toward one hip.
The cover must be closed for the pedometer to work.To
avoid losing or dropping your pedometer, use the included
leash and clip to fasten the pedometer securely to your
clothing.
Attaching the Leash: Attach the pedometer to the leash by
looping the leash around the pedometer belt clip. Next, clasp
the waistband of your clothing with the attached metal clip.
You can also use a safety pin to fasten the leash to your
clothing, or loop the leash through your belt or belt loop.
VIEWING YOUR RESULTS
Once you put on your pedometer with the cover closed,
it will automatically begin to record your steps, distance,
calories burned, and activity time. Repeatedly press the
yellow MODE button to cycle through the pedometer modes:
STEPS →DISTANCE →ACTIVITY TIMER →STEPS
ACCUSPLIT, Inc. • 2290M Ringwood Ave. • San Jose, CA 95131
800-965-2008 • 925-226-0888 • FAX [phone] • www.ACCUSPLIT.com • [e-mail]
10 steps
Congratulations on taking the first step to wellness
with your purchase of an ACCUSPLIT pedometer.
It’s easy to set up your new pedometer.
Just follow the steps below, and start walking!
MEMORY PEDOMETER
OPERATING INSTRUCTIONS
ACCUSPLIT®
EAGLE™1640M4
970-047
First, loop the
pedometer clip
Next, loop the metal
clip, then clasp clothing
Or, loop a
badge holder, then
put into pocket
(Badge holder
not included)
Or, loop a belt
or belt loop
Eat Right! Walk More! Live Well!
The ACCUSPLIT Lifestyle
ACCUSPLIT EAGLE 1640M4
TW15MG
TODAY TOTAL
MODE
SET
RESET
MY
3-WAY
PYRAMID
STEPS
™
MILES KM
DISTANCE
Aqua:
MODE
Cream:
SET
Yellow:
RESET
DISPLAY MODES
• STEPS - TODAY: Counts steps taken since last
 RESET.Resetdailytocounteachday’ssteps.
• STEPS - TOTAL: Keeps track of all steps taken,
 evenafterDay’sSTEPsare reset.
• DISTANCE: Shows distance walked or jogged since
last reset, in miles or kilometers.
• (ACTIVITY TIMER): Shows total activity time in
minutes and seconds since last reset. The timer runs
automatically whenever steps are being recorded.

MEMORIES
This pedometer has memories to keep track of your activity
data for today, this week, and last week. The unit stores
your steps, distance, calories, and activity time data for
each of these time periods. It can also display your daily
averages of these measures for the previous week.
To view today’s data, press the aqua DAY.CUM button until
a bar appears underneath the DAY indicator in top right
hand corner of display. Now, repeatedly press the yellow
MODE button to view steps, distance, calorie, and activity
time values for the day.
To view this week’s total data, press the aqua DAY.CUM
button until a bar appears underneath the CUM indicator in
top right hand corner of display. Now, repeatedly press the
yellow MODE button to view steps, distance, calorie, and
activity time values accumulated so far this week.
To view the previous week’s data, you must start from
the steps, distance, calories, or activity timer mode. Press
the cream MEMORY (WK-AVG) button until a bar appears
underneath the WEEK indicator in the top right hand
corner of display, and the indication “TL” (for Total)
appears on the left hand side of the display. The day of
the week indicators will all start to flash. Now, repeatedly
press the yellow MODE button to view the TOTAL steps,
distance, calorie, and activity time values for last week.
Press the cream MEMORY button once more to view the
DAILY AVERAGE of steps, distance, calories, and activity
time for last week. The indicator on the left hand side
of display will change to say “Avg” (for AVERAGE). To
exit back to today’s or this week’s data, press the cream
MEMORY button one more time.
REGISTER NOW Please return
your AE1640M4 Registration to
the Repair Center address in the
warranty, and we will let you know
about future products.
Email (preferred)
User
NO-PROOF-OF-PURCHASE LIMITED WARRANTY
See label inside the lid of your pedometer
AUTO MOVEMENT SENSOR
1. To filter out random movements, the unit remains in
standby mode until 5 continuous steps are registered.
Only then are the 5 steps calculated in, and an Active
indicator “▲” appears on the upper left of display.
2. When regular walk/run movement stops, after 2 seconds
the timer pauses and the unit switches to standby status
(Active indicator “▲” disappears).
RESETTING YOUR PEDOMETER
Most people prefer to reset step counts daily.To reset: While
displaying Day’s STEPs, DISTANCE, or ACTIVITYTIME, press and
hold yellow RESET button for at least two seconds to reset all of
these to zero. When displayingTotal STEPs, press aqua RESET
button for two seconds to reset all counts, includingTotal STEPS,
to zero.
REPLACING THE BATTERY
When the display starts to dim or goes blank, it is time to replace
the battery.Your pedometer uses oneType LR43 (L1142) 1.5 volt
alkaline battery.To replace:
1. Insert a coin into the slot on the bottom of the case, and twist
counterclockwise to loosen the case front. Lift case front away.
2. Using a pen or other thin object, push battery sideways out
of its holder. Replace it with a new battery.The battery’s
positive (+) terminal should be FACE UP while you put it into
the pedometer.
3. Align case front over the pedometer and press gently to snap
cover back into place, starting with top.