ACME LED MOOD Series User manual

LED MOOD Series
User Manual
COLOR COMMANDER
For Color Ball
Color Tube
Color Inset
Applications
Please read the instructions carefully before use
1B
TABLE OF CONTENTS
1. Safety Instruction
2. Features
3. Technical Specification
4. Overview
4.1 Front View
4.2 Rear View
5. How to set the unit
6. Installation
7. DMX 512 Configuration
8. DMX 512 Connection
9. Battery
10. Fixture Cleaning

2B
1. Safety Instructions
Please read the User Manual carefully as it including important information regarding details
of operation, maintenance and technical data. Keep this manual with unit for future
consultation.
WARNING！
●Avoiding any flammable liquids, water or metal objects enter into the unit.
●IF any liquid spill on the unit, DISCONNECT the power supply immediately.
●When serious operation problem happen, STOP using the unit immediately and contact
your local dealer for service.
●DO NOT open the unit because there are no user serviceable parts inside.
●NEVER try to repair the unit yourself. Repairs by unqualified people could cause damage
or faulty operation. Please contact your nearest dealer for any service.
CAUTION！
●After removed the package, checking the unit is NOT damaged in any way. DON'T use it
with doubt and contact an authorized dealer.
●NEVER use the unit under the excessive humidity and a temperature over 40℃.
●Do not try to dismantle or modify the unit.
3B
2. Features
Color Commander (LED-CC)
●A professional user friendly controller equipped with 4 channels.
●Equipped with 9 different hold-color buttons for instant colors.
●Comes with 32 spectrum mix colors, color fade, and 12 different chase patterns.
Providing the richest color burst for the show.
●Speed and dimmer adjustable for both color fade and color chase.
●Sound activated function is available.
●Full on and Blackout functions.
3. Technical Specification
¥Power supply
Input Voltage：AC 100V/120V/230V/240/250 50/60Hz
Output Voltage：DC 24V 150W max. x 2 ( 300W totally)
Fuse: T5A
¥DMX Input
Control: DMX 512
DMX connection: 3-pin Male XLR-sockets
¥DMX Channels
Channel 1 = Red
Channel 2 = Green
Channel 3 = Blue
Channel 4 = Dimmer/Strobe
¥Battery：AA NI-MH 1.2V X3 pcs (At least 1300 mAh each, optional)
¥Dimension：330×202×106 mm
¥Weight：6.6 kgs

4B
4. Overview
4.1 Front View
DMX On DMX Input
MASTER On Master Mode
SLAVE On Slave Mode
1. LED
SOUND Blinking Sound activated Mode
2. Display To show the various menu and selected functions
3. Menu Press the button to select the programming functions.
4. Enter Press the button to confirm the selected functions.
5. Up Press the button to go forward in the selected functions.
6. Down Press the button to go backward in the selected functions.
7. Hold Press the button to select color on Red / Orange / Yellow / Green /
Cyan / Blue / Purple / Magenta / White
8. Chase Press the button to select 12 chases patterns form chase slider
9. Spectrum mix Press the button to select 32 spectrum mix colors form spectrum mix
slider
5B
10. Chase slider
To choose chase patterns on Stander chase / Bright chase / Mood
chase / Spectrum random chase / Spectrum sequence chase /
Dynamic chase / Red-Green+ Blue / Green-Red+ Blue / Blue-Red /
Yellow-Blue / Red-Green / Yellow-Green
11. Spectrum mix
slider Use to control the Color fade and 32 spectrum color mix
12. Speed slider Use to adjust chase speed within the range of 0.1 to 2.5 seconds.
13. Fade slider Use to adjust time about fade in or fade out within the range of 2.5 to
12 seconds.
14. Master slider Use to dimmer /shutter the fixture
15. Sound Use to receive audio signal for sound activated
16. Full on All light effect at once
17. Blackout Blackout the fixture
4.2 Rear View
1. POWER For AC input and main fuse
2. ON/OFF Turns On/Off the power
3. MIC Use to receive external signal to trigger the unit in Sound-Active
mode.
4. DMX LINK Use 3-pin XLR plug cable to link the units together by DMX 512.
5. FUSE 6.3A For protection the DC output circuitry.
6. SINGLE OUTPUT For output DC 24V 300W max.

6B
5. How To Set The Unit
To select any of the given functions, press the MENU button until the required one is
showing on the display. Select the function by ENTER button and the display will blink. Use
DOWN and UP button to change the mode. Once the required mode has been selected,
press the ENTER button to setup or it will automatically return to the main functions without
any change after idling 8 seconds. To go back to the functions without any change press the
MENU button. The main functions are showing below:
DMX 512 Address Setting
Press the MENU button until the is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to change the to
DMX 512 address. Once the address has been selected, press the ENTER button
to setup or automatically return to the main functions without any change after 8 seconds. To
go back to the functions without any change press the MENU button again.
Timing setting
7B
Press the MENU button until the is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to change the to
timing setting (hours), Pressing ENTER button and the display will blink, use
DOWN and UP button to change the to timing setting (minute), Once the
hours or minute has been selected, press the ENTER button to setup or automatically return
to the main functions without any change after 8 seconds. To go back to the functions
without any change press the MENU button again.
Set Time 1 On
Set Time 2 On
Set Time 3 On
Press the MENU b button until the or( or ) is showing on the
display. Pressing ENTER button and the display will blink. Use DOWN and UP button to
change the to set time (hours), Pressing ENTER button and the display
will blink, use DOWN and UP button to change the to set time (minute),
Once the hours or minute has been selected, press the ENTER button to setup or
automatically return to the main functions without any change after 8 seconds. To go back to
the functions without any change press the MENU button again.
Set Time 1 Off
Set Time 2 Off
Set Time 3 Off
Press the MENU button until the or ( or ) is showing on the
display. Pressing ENTER button and the display will blink. Use DOWN and UP button to
change the to set time (hours), Pressing ENTER button and the display
will blink, use DOWN and UP button to change the to set time (minute),
Once the hours or minute has been selected, press the ENTER button to setup or
automatically return to the main functions without any change after 8 seconds. To go back to
the functions without any change press the MENU button again.

8B
Save Time 1 Scene
Save Time 2 Scene
Save Time 3 Scene
Press the MENU button until the or ( or ) is showing on the
display. Pressing ENTER button and the display will blink. To record the scene first time,
press the ENTER button to setup or automatically return to the main functions without any
change after 8 seconds ,To go back to the functions without any change press the MENU
button again.
6. Installation
CAUTIONS：Ensure the main power supply is off before installation or connect the
LED fixture.
Color Commander (LED-CC) could control the LED fixtures such as Color Ball (CB-12 only),
Color Tube (CT series) and Color Inset (CI-100 & CI-100F), The LED-CC total output is 300
watt and each of output is 150 watt. Please refer to the following diagram for the LED fixture
of power consumption.
Model Color Ball
CB-12
Color Inset
CI-100/100F
Color Tube
CT-100
Color Tube
CT-50
Color Tube
CT-20
Power
consumption 8W 3W 10W 5W 3W
Color Tube Installation
Please use an adapter cable to connect both terminal side of Color Tube, please make sure
the DMX input and DMX output of Color Tube was link Color Commander correctly.
9B
Color Ball Installation
Please use an adapter cable with 4 color wires to connect the terminal wires of Color Ball,
please make sure the color cables of Color Ball was correspond to the same color cables of
Color Commander correctly.
Color Inset Installation
Please use an adapter cable with 4 color wires to connect the terminal wires of Color Inset,
please make sure the color cables of Color Inset was correspond to the same color cables
of Color Commander correctly.
.

10B
7. DMX 512 Configuration
8. DMX 512 Connection
The unit will automatically switch between DMX function or run built-in pre-program shows.
Please refer to the following diagram to link multi-controllers.
11B
9. Battery
Inside with Time setting, the fixture will need 3 units of AA NI-MH 1.2V batteries (At least
1300 mAh each, optional). Please refer to the following diagram to change the batteries.
10. Fixture Cleaning
The cleaning of internal and external must be carried out periodically to optimize light output.
Cleaning frequency depends on the environment in which the fixture operates: damp, smoky
or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
 Clean with soft cloth using normal glass cleaning fluid.
 Always dry the parts carefully.
 Clean the external optics at least every 20 days. Clean the internal optics at least every
30/60 days.
Innovation, Quality, Performance