Acorn Neo-metro SLAB CSB3636 Instruction manual

INSTALLATION, OPERATION
& MAINTENANCE MANUAL
NEO-METRO FIELD SERVICE
TOLL FREE LOCAL FAX[phone] • 626-855-4866 • 626-855-4863
Date: 01/31/22
Part #: 0696-001-001
Page of 41
SLAB SHOWER BASES
RECOMMENDED CLEANING & MAINTENANCE
PROCEDURES
SLAB SOLID SURFACE SHOWER BASES
Acorn’s Corterra Solid Surface material is composed of Cast Polyester Resin, Aluminum
Trihydrate and Fillers. It is resistant to stains, impacts and burns. Complies with ANSI
Z124.3.
Wash with a non-abrasive all-purpose cleaner and rinse with water. Wipe dry. Never use
cleansers with strong chemicals such as toilet bowl cleaners, rust removers, ceramic
cooktop cleaners, paint or varnish removers, drain cleaners, metal cleaners, laquer
thinners or oven cleaners.
Surface damage, such as minor chips, scratches, burn marks and graffiti can be
repaired with a fine grit abrasive cleaner, a Scotch-Brite pad or fine grit sandpaper. For
more serious physical damage caused by vandalism, an Acorn Solid Surface Repair Kit
is available. Contact factory for details.
SLAB SOLID SURFACE
CSB6030
SLAB Shower Base:
CSB6030ADA
CSB3636
CSB3636ADA
SHOWER BASE Model Shown: CSB3636ADA
N E O - M E T R O b y A C O R N
®®
Acorn Engineering Company
15125 Proctor Ave. • City of Industry, CA 91746 USA
TF 800.488.8999 • PH 626.336.4561 • FX 626.961.2200

INSTALLATION, OPERATION
& MAINTENANCE MANUAL
NEO-METRO FIELD SERVICE
TOLL FREE LOCAL FAX[phone] • 626-855-4866 • 626-855-4863
Date: 01/31/22
Part #: 0696-001-001
Page of 42
REMOVE SHOWER BASE CAREFULLY
FROM PACKAGING
REMOVE PACKAGING
WITH CARE
ACORN
AVOID STANDING
BASE ON EDGES
1
Carefully remove from packaging prior to
installation. Inspect for any damage. Avoid
placing on its edges; this precaution will
prevent damage to corners.
Base
Base
HANDLING
2
Level carefully. For proper installation,
establish a 1/4” maximum clearance between
the and the walls. Place up to ½” of
Mortar or Thinset and screed in area where the
Base
Base
Base is to be installed. This procedure is
recommended in order to support the
should the Sub-Floor be uneven. Taper the
Mortar/Thinset to a 1/4” thickness around the
Drain Floor. DO NOT place Mortar/Thinset
closer than 2” from the edge of the or the
Floor Drain opening.
Base
Base
LEVELING
3WARNING!
DO NOT DROP BASE OVER EXPOSED PIPE
It is advisable to remove Drain Pipe prior to
setting in place. Insert Pipe through
Drain in into P-Trap. Tighten with an
Internal Pipe Wrench.
Base
Base
THINSET OR
MORTAR BED
SUB-FLOOR
DOTTED AREA IS
FOR CORTERRA BASE
REMOVE PIPE
FROM P-TRAP
RE-INSERT PIPE AND TIGHTEN
WITH AN INTERNAL WRENCH
RECOMMENDED
1/4” SPACE
1/4" MAX.
EXPANSION GAP

INSTALLATION, OPERATION
& MAINTENANCE MANUAL
NEO-METRO FIELD SERVICE
TOLL FREE LOCAL FAX[phone] • 626-855-4866 • 626-855-4863
Date: 01/31/22
Part #: 0696-001-001
Page of 43
11114
6. Test connection before covering or
concealing. To test: Plug Drain and fill
Receptor with water. Check for leaks. This
must be done before finishing walls.
5B. Use Screwdriver if necessary.
7. Attach Drain Grate and Strainer to Drain
Assembly.
1. Remove Drain Grate and assemble Drain
Body to Corterra and tighten Locking
Nut to affix Drain to .
Base
Base
2. Cut & dry-fit Waste Pipe to 1/2” below
bottom of shower base.
3. Position Corterra over 2” IPS Waste
Pipe assembly and ensure the Pipe is
centered in the Drain Body. Use a
Carpenter’s Level to ensure base is level.
Base should be evenly supported.
Base
4. Lubricate Gasket with soap solution and
stretch over 2” Pipe with beveled edge and
push Gasket as far as possible into joint.
DRAIN AND WASTE INSTALLATION:
5A. Thread Caulking Nut with Wrench provided
to secure Drain to Pipe.
1
23
45A
5B
LOCKING NUT
FIBER WASHER RUBBER WASHER
DRAIN BODY
DRAIN GRATE
GRID STRAINER
CAULKING NUT WRENCH
RUBBER CAULKING
GASKET
DRAIN ASSEMBLY
CAULKING NUT
WRENCH
CAULKING NUT
CAULKING GASKET
CAULKING NUT
WRENCH
DRAIN ASSEMBLY
CORTERRA BASE
CAULKING NUT
1
2"
CORTERRA
BASE
FINISHED SUB
FLOOR
MORTAR OR
THINSET
5"
WASTE PIPE

INSTALLATION, OPERATION
& MAINTENANCE MANUAL
NEO-METRO FIELD SERVICE
TOLL FREE LOCAL FAX[phone] • 626-855-4866 • 626-855-4863
Date: 01/31/22
Part #: 0696-001-001
Page of 44
1. Allow the Rough Wall material with a gap of
approximately 1/2” (Do not allow Rough
Wall Material to overlap Tiling Flange)
2. Let Finished Wall (Tile, etc.) overlap and
rest on shoulder.
RECOMMENDED INSTALLATION FOR
MODEL WITH TILING FLANGE OPTIONS:
NOTE: Neo-Metro assumes no responsibility
for problems due to faulty installation or
inadequate floor support.
1111
5STEP 1:
1
2"
1
2"
LATH / PLASTER
BOARD, ETC.
MATERIAL (Tile, etc.)
FINISHED WALL
STEP 2:
DO NOT NAIL OR SCREW
FLANGE TO WALL