ActionTec 14 Mbps HomePlug Ethernet Adapter User manual

14 Mbps
HomePlug
Ethernet Adapter
Model #: HPE100I
User Manual
Ver 1.0
Solutions for the Digital Life™

i
Table of Contents
1 Introduction 1
Package Contents 1
Features 2
System Requirements 2
Getting to Know the Ethernet Adapter 3
Technical Support 4
2 Connecting the HomePlug Adapters 5
Connecting the Adapters 5
Installing the Configuration Utility 6
3 Using the Configuration Utility 7
Device 7
Network 9
Security 10
About 11
4 Troubleshooting 13
Troubleshooting 13
Frequently Asked Questions 14
5 Setting Up Static IP Address 17
Windows 98 SE 17
Windows Me 20
Windows 2000 23
Windows XP 27
6 Setting Up File and Printer Sharing 31
File Sharing 31
Printer Sharing 39
a Specifications 41
General 41
LED Indicators 42
Environmental 42
b Glossary 43
Notices 47
Regulatory Compliance Notices 47
Modifications 47
Miscellaneous Legal Notices 48
Limited Warranty 49

ii
Actiontec HomePlug Ethernet Adapter User Manual
ii
This page left intentionally blank.

1
Introduction
Thank you for purchasing the Actiontec HomePlug Ethernet Adapter. The
HomePlug Ethernet Adapter is one of the easiest ways to enjoy home or small
business networking. It operates on the HomePlug Powerline Specification 1.0
standard, providing data transfer speeds up to 14 Mbps over home AC wiring.
Since home power lines are the most pervasive medium in households, with multi-
ple outlets in every room, the HomePlug Ethernet Adapter allows multiple desktop
and laptop computers to be networked easily, enabling them to share an Internet
connection, printers, files, and games, without any additional wiring. If you want
to take your computer networking to the next level, the Actiontec HomePlug
Ethernet Adapter is sure to be one of the keys to your success.
Package Contents
Make sure the following items came in this package:
s Two Actiontec 14 Mbps HomePlug Ethernet Adapters
s Two Ethernet Cables
s Installation CD (includes this manual)
s Quick Start Guide
1

2
Actiontec HomePlug Ethernet Adapter User Manual
3
Chapter 1 Introduction
Features
s HomePlug 1.0 compliant
s 14 Mbps data rate (maximum)
s 56-bit DES encryption
s Two-pronged US power plug (fits ungrounded power outlets)
s Power and Link indicators
System Requirements
s At least 2 available power outlets
s Standard home power wiring
s Computer with the following:
· CD-ROM drive
· IBM compatible running at 200 MHz or better
· 64 MB of RAM
· Ethernet network adapter
· TCP/IP installed

2
Actiontec HomePlug Ethernet Adapter User Manual
3
Chapter 1 Introduction
Getting to Know the Ethernet Adapter
This section contains a quick description of the Adapter’s external features.
Front Panel
The Adapter’s front panel features 2 lights (LEDs):
Power Light
The Power light glows green when the Adapter is powered on, and remains off
(or dark) when no power is present.
Link Light
The Link light glows green when an Ethernet connection is detected, and blinks
when data is being transferred across the Adapter.

4
Actiontec HomePlug Ethernet Adapter User Manual
Bottom Panel
The Adapter’s bottom panel contains one Ethernet port:
Ethernet Port
The Ethernet port is used to connect the Adapter to a computer or gateway/
router via Ethernet cable.
Technical Support
Actiontec Electronics prides itself on making durable, high-quality, high-perfor-
mance products. If you need assistance, the Actiontec Technical Support Department
is available all day every day to provide professional support.
Actiontec Electronics, Inc.
760 N. Mary Avenue
Sunnyvale, CA 94085
Technical Support
Phone: (USA) 1-888-436-0657
(UK) 0845-65-80411
E-mail: http://support.actiontec.com/email_support/support_form.php
Internet: www.actiontec.com/support

5
Connecting the
HomePlug Adapters
To connect the Adapters, they must be connected to a computer, plugged into a
standard wall outlet, and the Configuration Utility loaded on the computer.
Connecting the Adapters
To use the Adapters properly, one Adapter must be connected to a computer, and
the other Adapter must be connected to a router/gateway connected to a computer.
Connecting an Adapter to a Computer
1. Get one Adapter and one Ethernet cable from the package.
2. Insert one end of the Ethernet cable into the Ethernet port of the Adapter.
3. Plug the Adapter into a wall outlet.
☞
Note: Do not plug the Adapter into a UPS or power strip with
surge protection. The Adapter’s network signal may not pass
through these devices.
4. Insert the other end of the Ethernet cable into an Ethernet port on the back of
a computer.
Connecting an Adapter to a Router/Gateway
1. Get one Adapter and one Ethernet cable from the package.
2. Insert one end of the Ethernet cable into the Ethernet port of the Adapter.
3. Plug the Adapter into a wall outlet.
☞
Note: Do not plug the Adapter into a UPS or power strip with
surge protection. The Adapter’s network signal may not pass
through these devices.
4. Insert the other end of the Ethernet cable into an Ethernet port on a router/
gateway connected to a computer.
2

6
Actiontec HomePlug Ethernet Adapter User Manual
5. Insert the other end of the Ethernet cable into an Ethernet port on a router/
gateway connected to a computer.
Next, follow the instructions in the next section, “Installing the Configuration
Utility.”
Installing the Configuration Utility
After connecting the Adapters, install the Configuration Utility:
1. Insert the Connection 1-2-3 CD in the CD-ROM drive of the computer con-
nected to an Adapter.
2. When this window appears, click Finish.
3. Repeat for other computers connected to an Adapter.
The HomePlug Adapters are now connected and ready to use, and the
Configuration Utility is loaded on the computers. Go to chapter 3, “Using the
Configuration Utility” for information about changing the default configuration
settings of the Adapter.

7
Using the
Configuration Utility
Once the Adapters have been properly connected and installed, the user can fur-
ther configure the Adapters using the Actiontec HomePlug Configuration Utility.
The Utility also provides information about the network. To access the Utility,
double-click on the Actiontec HomePlug Utility icon on the computer’s desktop.
The Utility appears on the desktop. See the following sections for more informa-
tion about the Utility’s capabilities.
Device
Selecting Device from the row of tabs near the top of the Utility’s window gener-
ates the “Device” tab.
3

8
Actiontec HomePlug Ethernet Adapter User Manual
9
Chapter 3 Using the Configuration Utility
State
The “State” text box in the Device tab displays the MAC (Media Access Control)
address of the Adapter connected to the computer.
Device List
The Device List (the list box at the center of the Device tab) displays all HomePlug
Adapters connected to the computer. To connect to another Adapter from the list,
select it, then click Connect. To refresh the list, click Refresh.
☞
Note: If no Adapter appears in the Device List, make sure the
Adapter is connected properly (with the appropriate Ethernet
cable) to the computer. Then, unplug the Adapter, and plug
it back in again. If, after performing these actions, no Adapter
appears in the Device List, the Adapter may be defective.
Contact technical support.
Link Quality
The “Link Quality” bar graph in the Device tab provides a graphical representation
of the quality of the network link between the Adapters.
Poor
When the Link Quality is “Poor,” the bar graph is short and shaded red. This
kind of network connection results in very slow or no communication between
the devices on the network.
☞
Note: If the Link Quality is Poor, or the MAC address of the
Adapter connected to the computer reads all zeroes, the Adapter
may be defective. Contact technical support.
Fair
When the Link Quality is “Fair,” the bar graph is shaded yellow. This kind of net-
work connection results in average communication speeds between the devices
on the network.

8
Actiontec HomePlug Ethernet Adapter User Manual
9
Chapter 3 Using the Configuration Utility
Excellent
When the Link Quality is “Excellent,” the bar graph is shaded green. This kind of
network connection results in high communication speeds (at or near 14 Mbps)
between the devices on the network.
Network
Selecting Network from the row of tabs near the top of the Utility’s window gener-
ates the “Network” tab.
Network List
The Network List (the list box at the center of the Network tab) lists all other
Adapters connected to this HomePlug network. Only Adapters with the same
password as the Adapter connected to this computer are shown on this list. The
available Adapters are listed by their MAC addresses, and include their data rate (in
megabytes per second).
Scan HomePlug Network
If additional Adapters have been added to the HomePlug network, click Scan
Home Plug Network to refresh the Network List.

10
Actiontec HomePlug Ethernet Adapter User Manual
11
Chapter 3 Using the Configuration Utility
Security
Selecting Security from the row of tabs near the top of the Utility’s window gener-
ates the “Security” tab.
Network Password
Security (56-bit encryption) is set by default when a HomePlug network is created.
The default password (HomePlug) should be changed when setting up the net-
work, and all Adapters connecting to the HomePlug network must have the same
password. Change the password by entering the new password in the “Network
Password” text box.
Device ID
Enter the Adapter’s Device ID in the “Device ID” text box. The Adapter’s Device ID
is printed on the back of the of the Adapter.
HomePlug Devices
The “HomePlug Devices” list box contains the Device IDs of all HomePlug devices
added to the network. To add a HomePlug device to the HomePlug Devices list
box, enter its Device ID in the Device ID text box, then click Add. To remove a
HomePlug device, highlight in the HomePlug Devices list box, then click Remove.

10
Actiontec HomePlug Ethernet Adapter User Manual
11
Chapter 3 Using the Configuration Utility
Setting up Security
To set up security on a HomePlug network:
1. Enter the Device ID of one of HomePlug Adapters on the network in the
Device ID text box.
2. Click Add.
3. The Adapter’s device ID appears in the HomePlug Devices list box. Repeat
steps 1 and 2 for all Adapters on the network.
4. When the device IDs for all Adapters of the network appear in the HomePlug
Devices list box, enter a new network password in the Network Password text
box.
5. Click Set Password for ALL HomePlug Devices.
About
Selecting About from the row of tabs near the top of the Utility’s window gener-
ates the “About” tab.
The About tab displays the HomePlug Configuration Utility version.

12
Actiontec HomePlug Ethernet Adapter User Manual
This page left intentionally blank.

13
Troubleshooting
This chapter contains a list of problems that may be encountered while using the
HomePlug Ethernet Adapter, and techniques to solve them. Note that these tech-
niques may not be successful in all cases. Also included is a list of frequently asked
questions.
Troubleshooting
The Power light doesn’t light up after I plug the Adapter into a wall outlet.
Make sure the wall outlet is working by plugging other electric devices into it. If
it is working, plug in the Adapter again, and if the Power light still doesn’t illu-
minate, try plugging it into other wall outlets. If the Adapter is still experiencing
this problem, contact technical support.
The Link light doesn’t light up on the Adapter.
If the Adapter’s Ethernet light is not illuminating, a LAN connection is not being
detected.
s Check the Ethernet adapter on the computer and make sure it is enabled
and working properly. Also, make sure the right type of Ethernet cable is
being used.
I can’t connect to the Internet or any of the other computers on the network.
s Make sure the IP address and TCP/IP protocol are set up properly for all the
computers on the network , then try to ping the gateway.
s Use the Adapter’s Configuration Utility to detect all other Adapters on the
network. Then, plug the Adapters into adjacent sockets. If the Ethernet lights
still don’t illuminate, contact technical support.
4

14
Actiontec HomePlug Ethernet Adapter User Manual
15
Chapter 4 Troubleshooting
The Power and Link lights are on, but I can’t access the router/gateway from
the computer
s Try plugging the Adapters in different power outlets, preferably closer
together.
s Make sure all Adapters on the network are using the same security parameters.
Frequently Asked Questions
What’s the transfer speed over the Adapter’s network?
The Adapter’s network transfer speed is 14 Mbps (maximum) over a standard
home power line network.
What’s the estimated range of the Adapter’s network?
Approximately 300 meters (~985 ft.) in wall power lines (one household).
Will the Adapter work in any home?
The Adapter will work in any home with built-in copper wiring. It may not
operate in some older homes (pre-1950) with alternate wiring.
Will the Adapter’s network signal pass through circuit breakers?
Yes, the Adapter’s network signal will pass through circuit breakers. It will not,
however, pass through power transformers.
Does the Adapter work with a 100 – 240V AC input ?
Yes.
Does using the Adapter cause any interference with other home network-
ing devices?
No. The Adapter operates at a different frequency than other power line control
devices and can co-exist with technologies such as X-10, CEBus, and LONworks.

14
Actiontec HomePlug Ethernet Adapter User Manual
15
Chapter 4 Troubleshooting
Can my neighbor receive the Adapter’s network signal?
It is possible for a neighbor to receive the network signal. To prevent this, change the
default 56-bit DES security encryption password on the Adapter (see chapter 3).
How do I find out what the current speed and signal strength of the
Adapter’s network is?
Run the Adapter’s Configuration Utility to show current speed and signal strength.
How many Adapters do I need to set up a network?
Two.
To set up the Adapter’s network correctly, do I have to install the
Configuration Utility on each computer on the network?
No, the Configuration Utility is a diagnostic and security tool. Since the Adapter
is fully plug-and-play compatible, it needs no software drivers to operate.
How many Adapters can be installed on the same LAN (local area network)?
Actiontec recommends using no more than 16 Adapters on one network.

16
Actiontec HomePlug Ethernet Adapter User Manual
This page left intentionally blank.

17
Setting Up Static
IP Address
To communicate with a Home Plug Ethernet Adapter from a computer on the net-
work, the user may have to switch the IP address settings from DHCP-enabled to
static IP, so that the computer and the Adapter are on the same subnet.
To set up static IP on a computer, select the operating system and follow the
instructions.
☞ Note: The following procedures are based on the Adapter’s
factory default IP address. If the Adapter’s IP address has been
changed, enter the new IP address when instructed to enter an
IP address.
Windows 98 SE
1. From the desktop, click on the Start button in the lower left corner.
2. From the menu that appears, select Settings.
5