ActionTec USB Wireless Bluetooth Adapter User manual

Solutions for the Digital Life™
User Manual
USB
Wireless
BluetoothAdapter
Softwareversion: 1.1

1. Introduction 1
What is Bluetooth? 1
Package Contents 1
Minimum System Requirements 2
Technical Support 2
2. Installing the USB Wireless Bluetooth Adapter 3
2.1Install the Software 3
2.2Connect the Adapter 7
3. Working with Bluetooth 10
3.1 Start or Stop using the Adapter 10
3.2 Creating a Bluetooth Connection 10
3.3 Connect to Another Device 11
3.4 Connect to a Bluetooth Headset 16
4. Working with Bluetooth Software 18
4.1The Bluetooth Tray 18
4.2 Access My Bluetooth Places 19
4.3 Finding Bluetooth Devices 19
4.4 Finding Bluetooth Services 20
4.5 Bluetooth Connection Status 22
4.6 Bluetooth Devices and Services 23
4.7 Send to Bluetooth 25
5. Configuring for Other Services / Applications 27
5.1Opening Bluetooth Configuration 27
5.2 Bluetooth Services vs. Applications 27
5.3 The Bluetooth Exchange Folder 28
5.4 Configuration Settings 28
5.5 Bluetooth Applications 29
5.6 Bluetooth Services 41
Table of Contents Page
i

Actiontec USB Wireless Bluetooth Adapter
ii
Actiontec USB Wireless Bluetooth Adapter
5.7 Hardware Settings 51
5.8 Accessibility Settings 53
5.9 Discovery Settings 54
6. Security 56
7. Troubleshooting 59
8. Frequently Asked Questions 63
Notices 65
Regulatory Compliance Notices 65
Warranty statements 67
Proprietary Notice and Disclaimer
Unless otherwise noted, this document and the information herein disclosed are propri-
etary to Actiontec Electronics, Inc the manufacturer. Any person or entity to whom this
document is furnished or who otherwise has possession thereof, by acceptance agrees that
it will not be copied or reproduced in whole or in part, nor used in any manner except to
meet the purposes for which it was delivered.
The information in this document is subject to change without notice and should not
be construed as a commitment by Actiontec the manufacturer. Although Actiontec the
manufacturer will make every effort to inform users of substantive errors, Actiontec the
manufacturer disclaims all liability for any loss or damage resulting from the use of this
document or any hardware or software described herein, including without limitation
contingent, special or incidental liability.
Note: PC is a trademark of IBM Corporation. Windows 98 , Windows 98 SE, Windows NT,
and Windows XP is a trademark of Microsoft Inc. All other brand or product names and logos
used in this manual are trademarks or registered trademarks of their respective holders.

1
Introduction
Thank you for purchasing the Actiontec USB Wireless Bluetooth Adapter.
Now you can truly enjoy the freedom of wireless connectivity with Actiontec's
Bluetooth Adapter. Simply install the software and then plug this tiny adapter into
any USB port on your computer, and you can exchange information between it
and any other Bluetooth enabled device. Imagine sharing your Internet connec-
tion by simply requesting it from any computer, or PDA. Connect on the go by
using your cell phone as a high speed modem or simply print to any bluetooth
enabled printer, The Actiontec USB Wireless Bluetooth Adapter lets you enjoy the
freedom of true mobility whether you're at the office or on the move.
What is Bluetooth?
Bluetooth is a worldwide standard for digital wireless communication and data
exchange between multiple devices. Bluetooth compliant devices exchange data
by establishing a relationship with each other, the first device acting as a client,
requests a connection, while the second device acting as a server accepts or rejects
that request. Some Bluetooth devices can behave as client and server; however
other devices can only behave as a client.
Package Contents
Actiontec USB Wireless Bluetooth Adapter
Installation CD
Quick start guide
USB Extension Cable (Optional)
1

2
Actiontec USB Wireless Bluetooth Adapter
Minimum System Requirements
Microsoft Windows 98SE, ME, 2000, XP
Available USB Port
Pentium 90 or faster
16MB or RAM
TCP/IP installed
Technical Support
Actiontec Electronics prides itself on making high-quality, durable,
high-performance products. If you need assistance, the Actiontec Technical
Support Department is available every day 24 hours a day to provide professional
support.
Actiontec Electronics, Inc.
760 N. Mary Avenue
Sunnyvale, CA 94085
Technical Support
Phone: [phone]
E-mail: [e-mail]
Internet: www.actiontec.com/support

Installing the USB Wireless
Bluetooth Adapter
The instructions that follow provide a visual guide to setting up the Actiontec
USB Wireless Bluetooth Adapter. It is recommended the user follow these
instructions prior to attempting any other procedures. This manual will guide
you through the hardware and software installation and configuration.
2.1 Install the Software
"STOP!!!: You must install the Bluetooth Software PRIOR to connecting
your Bluetooth Adapter to the computer. If you have already
connected the Bluetooth Adapter, please remove it now and restart
your computer.
1. Make sure your computer is turned on, then put the Actiontec Installation
CD-ROM in your CD-ROM drive.
2. The Installation software should start automatically. This may take a few
moments.
When you see this window. Click Next to continue
"Note: If you do not see the window above, click Start on the taskbar
and then select Run. Type d:/setup (or e:/setup, depending on the
drive letter of your CD-ROM drive), then click OK.
3
2

4
Actiontec USB Wireless Bluetooth Adapter
3. When you see the License Agreement screen appear, read the License
Agreement carefully. Click the circle next to “I accept the terms in the license
agreement” and then click Next to continue.
"Note: If you do not agree with the terms of the license agreement,
click the circle next to “I do not accept the terms in the license
agreement” and click Next. Now you have terminated the installation
of this Bluetooth Adapter.
4. Click Next to continue.
5. Click Install to continue.

5
Chapter 2 Installing the USB Wireless Bluetooth Adapter
6. You will see this window. Please be patient as it will take several minutes to
install your Bluetooth software.
You may need to have your Windows CD handy.
7. You may see this screen. If you do, click OK.
8. Click Finish to complete the software installation. Please remove any CD
from the CD-ROM drive before restarting your computer.

6
Actiontec USB Wireless Bluetooth Adapter
9. Click Ye s to complete the software installation and restart your computer
now.
"Note: If you are running Windows XP, you may not need to
restart your computer.

7
Chapter 2 Installing the USB Wireless Bluetooth Adapter
2.2 Connect the Adapter
1. Get the Bluetooth Adapter from the Actiontec Quick Start Kit
2. Take the cap off of the Bluetooth Adapter.
3. Follow the instructions for the type of computer that you are using.
Windows XP Users! You may see a Found New Hardware Wizard screen, once
you connect the Bluetooth Adapter to your computer. Please see below for
detailed instructions.
a. The “Found New Hardware Wizard” will run and the following screen will
appear, make sure “Install the software automatically (Recommended)” is
selected. When ready click Next to continue.
b. The following screen appears, Click on Finish to complete the installation
process.

8
Actiontec USB Wireless Bluetooth Adapter
Laptop Users: Insert the Bluetooth Adapter into an open USB port.
Desktop Users:
a.) Get the USB Extension Cable from the Quick Start Kit.
b.) Insert one end into an open USB port on the computer.
"Note: The USB Port is shaped like a thin rectangle about ¼ inch by ½
inch and may be horizontal or vertical.
c.) Plug the other end into the Bluetooth Adapter

9
Chapter 2 Installing the USB Wireless Bluetooth Adapter
d.) Set the Bluetooth Adapter on top of your monitor where it can receive a clear
signal.
4.Make sure the light on the Bluetooth Adapter is SOLID GREEN.
Congratulations, you have successfully installed the Actiontec USB Wireless
Bluetooth Adapter. To begin using your Bluetooth Adapter, doubleclick on the
“My Bluetooth Places” icon that appears on your desktop.

10
Working with Bluetooth
The Actiontec USB Wireless Bluetooth Adapter can communicate with any
Bluetooth-enabled device wirelessly, in order to accomplish this a relationship
with the device must be established. This chapter will guide you on the different
functions and methods for operating your Actiontec USB Wireless Bluetooth
Adapter.
3.1 Start or Stop using the Adapter
• Starting the Actiontec USB Wireless Bluetooth Adapter
In the Windows system tray, right-click the Bluetooth icon an select Start
Bluetooth Device. The Bluetooth icon is blue in color with a white insert
when Bluetooth is running.
• Stopping the Actiontec USB Wireless Bluetooth Adapter
In the Windows system tray, right-click the Bluetooth icon and select Stop
Bluetooth Device. The Bluetooth icon is blue in color with a red insert
when Bluetooth is stopped.
3.2 Creating a Bluetooth Connection
To establish a relationship with other Bluetooth-enabled devices. To create a
connection between your Bluetooth-enabled computer and any Bluetooth-enabled
device, follow any of the methods described below.
• Option 1: Creating a Connection from the System Tray
In the Windows system tray which is located in the bottom right hand
corner, right-click the Bluetooth icon, select Quick Connect and then
the Bluetooth service that you wish to use.
If this computer has created a connection to the desired type of service
in the past, the options on the shortcut menu are:
• The name(s) of any device(s) with which prior connections to this type
of service have been established. Select a name from the list to
re-establish connection.
• Other Devices…Select this option to search for additional devices that
potentially provide the desired service, select a device from the list, and
then click Connect.
3

11
Actiontec USB Wireless Bluetooth Adapter
If this computer has never created a connection to this type of service,
the only option on the shortcut menu is “Find Devices….” Select this
option to search for devices that potentially provide the desired service,
select a device from the list, and then click Connect.
• Option 2: Creating a Connection Using the Bluetooth Setup Wizard
Launch the Bluetooth Setup Wizard by following this simple step.
• Right-click the Bluetooth icon on your desktop and select
Bluetooth Setup Wizard. Once launched, Follow the Bluetooth
Wizard instructions.
3.3 Connect to Another Device
3.3.1 Pairing With a Bluetooth Enabled PC
In this section we will show you how to connect to another computer. In
the world of Bluetooth, we call this “pairing”. If you would like to connect
or “pair” your computer to another device like a Bluetooth cell phone or
keyboard, please go to section 3.4.2 of this User’s Manual.
1. Make sure that you have the Bluetooth Adapter installed and configured
on each computer or device.
2. Double-click on the My Bluetooth Places icon that is on your desktop.
3. Click on the Bluetooth Setup Wizard icon.

12
Chapter 3 Working with Bluetooth
4. Click the circle next to “I want to find a specific Bluetooth device and
configure how this computer will use its services”. Then click Next to
continue.
5. Once you see the other computer displayed, click on its icon and then click
Next.

13
Actiontec USB Wireless Bluetooth Adapter
6. Pick a simple “Pairing” code and enter it in the box next to “PIN Code”. The
code should be numbers only, and we recommend using '0000' or '1234'.
Write down this code below because you will need to enter the exact same
code on the second computer.
PIN Code: __________________
Once you have entered the PIN Code, make sure to click Initiate Pairing.
Do NOT press the Enter key at this time.
7. Go to the second computer. You should see a window similar to the once
below. Enter the same PIN code that you used on the fist computer. Click
OK.

14
Chapter 3 Working with Bluetooth
3.3.2 Pairing With Non-PC Bluetooth Devices
Pairing with devices other than PCs can be easily accomplished through
the use of the Bluetooth Setup Wizard. We strongly suggest reading the
user manual for the Bluetooth device to be paired with your Bluetooth
Ready PC.
The following instructions will help to configure you PC to connect to
a Cell Phone. If you would like to connect or "pair" your computer to
another device like a PDA, please go to Chapter 5 of this User's Manual..
1. Make sure that you have the Bluetooth Adapter installed and configured
on each computer or device.
2. Click on the My Bluetooth Places icon that is on your desktop.
3. Click on the Bluetooth Setup Wizard icon.
4. Click the circle next to “I want to find a specific Bluetooth device and
configure how this computer will use its services”. Then click Next to
continue.

15
Actiontec USB Wireless Bluetooth Adapter
5. Once you see the other device displayed, click on its icon and then click Next.
6. Enter the device’s “Pairing” code in the box next to “PIN Code”.
(Note: Some Bluetooth devices may already have a default PIN code. Please
refer to the device's user manual.) The code should be numbers only. Write
down this code below because you will need to enter the exact same code on
the Bluetooth device being paired.
PIN Code: __________________
Once you have entered the PIN Code, click Initiate Pairing.
7. Go to the device you are pairing. You should see a window similar to the
once below. Enter the same PIN code that you used on the first computer.
Click OK.
Pairing procedures can be different and are determined by the device manufacturer.
Make sure you know the device’s Pairing ID prior to pairing. If a device does NOT
come with a preset Pairing ID, then you may select one of your own.

16
Chapter 3 Working with Bluetooth
3.4 Connect to a Bluetooth Headset
1. Put your Bluetooth headset in discovery mode by pressing and holding the
On button for 4-6 seconds. (Each headset has a different setting so make sure and
have your Bluetooth Headset manual ready.)
2. Double-click on the My Bluetooth Places icon on your computer desktop.
3. Double-click on the Find Bluetooth Devices icon. If nothing shows up,
press F5 or refresh to search again. The BT Headset icon should appear
4. Right-click on the Bluetooth Headset Icon and select Pair Device
5. Enter the headset's PIN code (Refer to the headset manual)
6. Double-click on the Bluetooth Headset icon.

17
Actiontec USB Wireless Bluetooth Adapter
7. Double-click on the Headset on BT Headset icon. (The service name may
vary.
8. When you hear a musical tone from the headset, press the On button on
the headset to complete the connection.
Congratulations! You've connected your Bluetooth Headset to your PC. Now
you can enjoy listening to music or chatting with your friends online from your
wireless headset.