ACU-RITE 01202 User manual

Instruction Manual
SAVE THIS MANUAL FOR FUTURE REFERENCE.
CONTENTS
Unpacking Instructions ........... 2
Package Contents .................. 2
Product Registration ............... 2
Features and Benets: Sensor ... 2
Features and Benets: Display ... 3
Setup .................................... 6
Sensor Setup ......................... 6
Display Setup ........................ 7
Set the Time, Date and Units.... 8
Backlight Settings................... 8
Placement Guidelines ............. 9
Using the Weather Station.....10
Programmable Alarms........... 11
Troubleshooting ....................12
Care and Maintenance .........13
Calibration ...........................13
Specications........................14
FCC Information ...................14
Customer Support .................15
Warranty..............................15
Weather Station
model 01202
Questions? Contact Customer Support at
www.AcuRite.com/support or email [e-mail]

2
Congratulations on your new AcuRite product. To ensure the best possible
product performance, please read this manual in its entirety and retain it for
future reference.
Unpacking Instructions
Remove the protective lm that is applied to the LCD screen prior to using this
product. Locate the tab and peel off to remove.
Package Contents
1. Display
2. Outdoor Sensor
3. Power Adapter
4. Instruction Manual
Features and Benets
4
3
2
1
5
OUTDOOR SENSOR
1. Integrated Hanger
For easy placement.
2. Wireless Signal Indicator
Flashes when data is being sent to the
display.
3. Battery Compartment
4. A-B-C Switch
ID code that must match display’s
A-B-C switch to ensure units
synchronize.
5. Battery Compartment Cover
PRODUCT REGISTRATION
Register online to receive 1 year of warranty protection
www.AcuRite.com
IMPORTANT PRODUCT MUST BE REGISTERED
TO RECEIVE WARRANTY SERVICE

3
Wi-Fi Setup for Weather UndergroundTM and Dark Sky
Forecast
This weather station features wireless internet connectivity in order to connect and down-
load forecasts from Dark Sky. You also have the option to share your temperature and
humidity data with Weather Underground, but this is not required to get a forecast.
2. Power on the display using included power cord. If the unit has been powered on for
more than 30 minutes, press and release the “ ”
button to re-activate Wi-Fi setup.
3. Connect to the Wi-Fi signal (named AcuRite
01202M)of the AcuRite display from your
computer or mobile device.
1. (OPTIONAL) If you do not already have a WU (Weather UndergroundTM) account
and would like to send your data to WU, please create your account at
wunderground.com prior to following the next steps. To add this weather station to
your WU account:
Sign in to your Weather UndergroundTM account.
N
Enter all required location info.
When prompted for “Station Hardware”, select “AcuRite Pro Weather Center”.
You will be provided with a WU Station ID and Station Key once you have
submitted all required info (record for step 5, below).
5. Select or enter your wireless network name and password. Fill in your country and
postal code to download your 2-day forecast from Dark Sky. If you want to send
data to Weather Underground, enter your Station ID and Station Key. Press“Save”
to save your credentials.
NOTE: This weather station display only supports 2.4 GHz wireless networks.
6. A W
connection was not successful, please verify your credentials and/or visit the
Troubleshooting section (see page 13).
7. Within an hour after the display is connected to Wi-Fi, forecasts from Dark Sky will
be shown on your display. If you entered your WU credentials, data from your
sensor will automatically begin to upload to Weather UndergroundTM. Monitor
sensor data remotely at www.wunderground.com or from a mobile device using
the Weather UndergroundTM app, available from the iOS App Store or Google
Play Store.
4. Open your web browser on the device that is
connected to the AcuRite display. Type
“192.168.4.1” in the address bar and hit enter to
access the AcuRite Wi-Fi display settings website
(shown right).

4
Features and Benets
BACK OF DISPLAY
1. Integrated Hang Hole
For easy wall mounting.
2. Fold-out Tabletop Stand
3. Power Adapter
4. Plug-in for Power Adapter
5. RESET Button
For full reset to factory defaults.
6. A-B-C Switch
ID code that must match sensor’s
A-B-C switch to ensure units
synchronize.
7. Backup Battery Compartment
8. Battery Compartment Cover
(not shown)
3
6
7
5
4
2
1

5
1
2
3
4
5
6
7
17
18
15
14
2
11
10
8 9
13
16
19
!
12

6
1. Current Outdoor Temperature
Arrow icon indicates the direction
temperature is trending.
2. Chance of Rain Indicator
Indicates the likelihood of rain when
connected to Wi-Fi.
3. Today’s Forecast
Includes forecasted high & low
temperatures. Powered by Dark Sky
when connected to Wi-Fi.
4. Current Indoor Temperature
Arrow icon indicates direction
temperature is trending.
5. Date
6. Button
For viewing daily high & low records
7. and Buttons
For setup preferences
8. Sensor Low Battery Indicator
9. Outdoor Sensor Signal Strength
10. Current Outdoor Humidity
Arrow icon indicates the direction
humidity is trending.
11. Icon
Indicates display is connected to your
wireless network in addition to the
signal strength.
12. Severe Weather Indicator
Indicates one of the following is in the
forecast:
•Wind
•Sleet
•Possible Tornado
•Hail
•Ice
•Fog
13. Tomorrow’s Forecast
Includes forecasted high & low
temperatures. Powered by Dark Sky
when connected to Wi-Fi.
14. Current Indoor Humidity
Arrow icon indicates direction
humidity is trending.
15. Clock
16. Display Low Battery Indicator
17. Auto Dim Icon
Indicates display is in auto-dimming
brightness mode (see page 9).
18. Button
For setup preferences.
19. Button
For momentary backlight and
dimmer settings.
20. Yesterday’s Conditions
(not shown)
Includes high & low temperature
readings. Only shown when not
connected to Wi-Fi (see page 11).
max
min
ON

7
SETUP
Sensor Setup
Set the A-B-C Switch
The A-B-C switch is located inside
the battery compartment. It can
be set to A, B or C. However,
you must select the same letter
choices for both the sensor and
the display in order for the units
to synchronize.
Install or Replace Batteries
AcuRite recommends high quality
alkaline batteries in the outdoor
sensor for the best product
performance. Heavy duty or
rechargeable batteries are not
recommended.
1. Slide off the battery
compartment cover. Take
note of the A-B-C switch
setting inside the battery
compartment for display
setup.
2. Insert 2 x AA batteries into
the battery compartment, as
shown. Follow the polarity
(+/-) diagram in the battery
compartment.
3. Replace the battery cover.
2
1
2Install Batteries
2 AA batteries
A B C
1A-B-C Switch
Set to match
display

8
PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE
WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.
BATTERY SAFETY: Clean the battery contacts and also those of the device prior to battery installation. Remove batteries from equipment that will not
be used for an extended period of time. Follow the polarity (+/-) diagram in the battery compartment. Promptly remove dead batteries from the device. Dispose of
used batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries
recharge non-rechargeable batteries. DO NOT short-circuit the supply terminals.
IMPORTANT: Batteries are
a backup power source to
preserve records in the event of
a power outage. Display will
not have Wi-Fi functionality on
batteries alone. Power adapter
is recommended as the primary
power source to enjoy the full
functionality of this product.
Display Setup
1Set the A-B-C Switch
Locate the A-B-C switch inside
the battery compartment. Set
the A-B-C switch to A, B or C.
You must select the same letter
choices for both the display and
the sensor in order for the units to
synchronize.
Install or Replace Backup
Batteries (optional)
1. Remove the battery
compartment cover.
2. Insert 3 x AAA alkaline
batteries into the battery
compartment, as shown. Follow
the polarity (+/–) diagram in
the battery compartment.
3. Replace the battery cover.
Plug in Power Adapter
For the best performance, plug
in the power adapter as the main
power source for this product.
3Plug in
Power
Adapter
1A-B-C Switch
Set to match
sensor
2
3
Install Backup
Batteries
3 AAA Batteries
(optional)
2
A B C

9
Set the Time, Date and Units
Press and release the “ ” button, located on the front of the display, to enter
SET MODE. Once in set mode, the preference you are currently setting will
blink on the display.
To adjust the currently selected (ashing) item, press and release the “ “ or
“ “ buttons (press and HOLD to fast adjust).
To save your adjustments, press and release the “ ” button again to adjust the
next preference. The preference set order is as follows:
Auto Change for DST (Daylight Saving Time YES or NO)*
CLOCK HOUR
CLOCK MINUTE
CALENDAR MONTH
CALENDAR DATE
CALENDAR YEAR
TEMPERATURE UNITS (ºC or ºF)
*If you live in an area that observes DST, DST should be set to YES, even if it is
not currently Daylight Saving Time.
You will automatically exit SET MODE if no buttons are pressed for 10 seconds.
Enter setup mode at any time by pressing the “ ” button.
Display Backlight Settings
This weather station’s colour display features three different lighting settings:
High (100%) brightness, Medium (50%) brightness and Low (15%) brightness.
Using battery power alone, the backlight is available momentarily for 10
seconds by pressing the Backlight button.
When display is powered with the power adapter, backlight remains on at
100% brightness. Press “ ” button once to dim to 50% brightness; press
again to dim to 15%, press a 3rd time to enter AUTO DIM mode. “AUTO
DIM” will appear next to the clock.
NOTE: Pressing and holding the “ ” button for 5 seconds will disable the
backlight. Once any button is pressed, the backlight will return to your selected
setting.
AUTO DIM MODE: Automatically adjusts display brightness based on time of day.
6:00 a.m. - 9:00 p.m. = 100% brightness
9:01 p.m. - 5:59 a.m.= 15% brightness

10
Placement for Maximum Accuracy
AcuRite sensors are sensitive to surrounding environmental conditions. Proper
placement of both the display and outdoor sensor are critical to the accuracy
and performance of this product.
Display Placement
Place the display in a dry area free of dirt and dust. Display
stands upright for tabletop use and is wall-mountable.
Outdoor Sensor Placement
Sensor must be placed outside to observe outdoor conditions.
Sensor is water resistant and is designed for general outdoor
use, however, to extend its life place the sensor in an area
protected from direct weather elements.
Hang the sensor using the integrated hang hole or hanger,
or by using string (not included) to hang it from a suitable
location, like a well covered tree branch. The best location is
4 to 8 feet (1 to 2 metres) above the ground with permanent
shade and plenty of fresh air to circulate around the sensor.
Important Placement Guidelines
• To ensure accurate temperature measurement, place units out of direct
sunlight and away from any heat sources or vents.
• Display and outdoor sensor must be within 330 ft (100 m) of each other.
• To maximize wireless range, place units away from large metallic items, thick
walls, metal surfaces, or other objects that may limit wireless communication.
• To prevent wireless interference, place both units at least 3 ft (90 cm) away
from electronic devices (TV, computer, microwave, radio, etc.).
(100 metres maximum)
(330 feet)
3 feet
(90 cm)
Setup is Complete
The sensor will now synchronize with the display. It may take a few minutes for
synchronization to complete. Please refer to the troubleshooting section of this
manual if anything appears to be functioning improperly.