Acuity Brands HEALTHCARE LIGHTING RK1HPL User manual

HPL Luminaire
REPAIR KIT INSTRUCTIONS
A. General Identification of HPL Luminaire……………......................................................................................................................Page 2
B. Exploded View of RK1HPL, RK3HPL, and RK6HPL......................................................................................................................Page 3
C. RK1HPL Components…………………..….……………..........................................................................................................................Page 4-5
D. RK2HPL General Layouts…………………….…………….......................................................................................................................Page 6
E. RK3HPL Components………….……………………………………...............................................................................................................Page 7
F. RK6HPL Components………….……………………………………...............................................................................................................Page 8
8/2021 ECO# XXXXX
2
A. General Identification of HPL Luminaire
IMPORTANT: Wearcottongloves ANDlift and handle theluminaire from theends to avoid damaging or soiling thelens
surface. Should the lens surface become smudged or otherwise blemished, clean using only a soft, microfiber cottoncloth.
LENS
912-00300-004 REV. A
One Lithonia Way, Conyers, GA 30012 • Tel: 800-705-SERV (7378) • Website: https://acuitybrands.com/
©2021 Acuity Brands Lighting, Inc.All Rights Reserved.“Healthcare Lighting” is aregistered trademark of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending.Specifications subject to change without notice.Limited warranty
applies.Complete warranty terms located at www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx
ELECTRICAL ACCESS PLATE
CEILING TRIM ACCESSORIES
(WILL VARY BASED ON APPLICATION)
ELECTRICAL ENCLOSURE
LOCATION OF INSULATION
DETECTORS
(IF APPLICABLE)
HPL REPAIR KIT INSTRUCTIONS
LOCATION OF NLIGHT RJ45
(IF APPLICABLE)
LOCATION OF NLIGHTAIR
ANTENNA
(IF APPLICABLE)
END PLATE

3
©2021 Acuity Brands Lighting, Inc.All Rights Reserved.“Healthcare Lighting” is aregistered trademark of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending.Specifications subject to change without notice.Limited warranty
applies.Complete warranty terms located at www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx
8/2021
912-00300-004
B. Exploded View of RK1HPL, RK3HPL, and RK6HPL
RK1HPL KIT
RK3HPL KIT
HPL REPAIR KIT INSTRUCTIONS
**IMPORTANT**
-RK1HPL Kit: LED Board screw torque 11 in/lb +/-4 in/lb
-All other fasteners 17 in/lb +/-4 in/lb
RK6HPL KIT
One Lithonia Way, Conyers, GA 30012 • Tel: 800-705-SERV (7378) • Website: https://acuitybrands.com/

C. RK1HPL Components
HPL REPAIR KIT INSTRUCTIONS 4
8/2021
912-00300-004
©2021 Acuity Brands Lighting, Inc.All Rights Reserved.“Healthcare Lighting” is aregistered trademark of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending.Specifications subject to change without notice.Limited warranty
applies.Complete warranty terms located at www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx
RK1HPL XXLONG: Components provided in kits listed below.
8.875” Light Engine 11.875” Light Engine
11.3875” Light Engine
PCBAS QTY SCREW QTY WIRES
24LONG 8.875” 18 2
11.875” 1
36LONG 11.3875” 312 4
48LONG 11.3875” 316 6
11.875” 1
72LONG 11.3875” 224 8
11.875” 4
96LONG 11.3875” 232 12
11.875” 6
Note: FC100 ships double the quantities shown.
One Lithonia Way, Conyers, GA 30012 • Tel: 800-705-SERV (7378) • Website: https://acuitybrands.com/

HPL REPAIR KIT INSTRUCTIONS 5
8/2021
912-00300-004
©2021 Acuity Brands Lighting, Inc.All Rights Reserved.“Healthcare Lighting” is aregistered trademark of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending.Specifications subject to change without notice.Limited warranty
applies.Complete warranty terms located at www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx
**IMPORTANT**
-RK1HPL Kit: LED Board screw torque 11 in/lb +/-4 in/lb
-All other fasteners 17 in/lb +/-4 in/lb
-RK1HPL Kit will come with replacement fasteners and jumper wires. New or existing fasteners and jumper wires
may be used during the repair process.
Remove lens by gently pressing on the center of
the lens and inserting a screwdriver between the
lens and the housing.
1 2
Disconnect damaged light engine by gently
pressing down on the channel connectors while
pulling outward on wire. Remove the #6-32
fasteners securing the light engine to the reflector.
3
Replace with new light engine by gently pushing
in wires into light engine connecter, then replacing
#6-32 fasteners. Test the fixture prior to
reinstalling the lens.
One Lithonia Way, Conyers, GA 30012 • Tel: 800-705-SERV (7378) • Website: https://acuitybrands.com/

6
©2021 Acuity Brands Lighting, Inc.All Rights Reserved.“Healthcare Lighting” is aregistered trademark of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending.Specifications subject to change without notice.Limited warranty
applies.Complete warranty terms located at www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx
8/2021
912-00300-004
C. RK2HPL –Driver Replacement
HPL REPAIR KIT INSTRUCTIONS
Remove lens by gently pressing on the center of
the lens and inserting a screwdriver between the
lens and the housing.
1 2
Remove the screws securing the reflector and
disconnect the PCBA wiring in the electrical
compartment.
With the reflector removed, release the wires by
pressing the button on the driver connectors.
Remove the 2 screws securing the driver to the
electrical enclosure.
3
One Lithonia Way, Conyers, GA 30012 • Tel: 800-705-SERV (7378) • Website: https://acuitybrands.com/

D. RK3HPL Components
HPL REPAIR KIT INSTRUCTIONS 7
8/2021
912-00232-001
©2021 Acuity Brands Lighting, Inc.All Rights Reserved.“Healthcare Lighting” is aregistered trademark of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending.Specifications subject to change without notice.Limited warranty
applies.Complete warranty terms located at www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx
RK3HPL XXLONG: Components provided in kits listed below.
Lens
Remove lens by gently pressing on the
center of the lens and inserting a screwdriver
between the lens and the housing.
12
To install new lens, seat one end of lens
against endplate, and press the lens along
the length. Listen for a snapping noise to
indicate the lens is fully seated.
One Lithonia Way, Conyers, GA 30012 • Tel: 800-705-SERV (7378) • Website: https://acuitybrands.com/

D. RK6HPL Components
HPL REPAIR KIT INSTRUCTIONS
8/2021
912-00300-004
©2021 Acuity Brands Lighting, Inc.All Rights Reserved.“Healthcare Lighting” is aregistered trademark of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending.Specifications subject to change without notice.Limited warranty
applies.Complete warranty terms located at www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx
RK6HPL : Components provided in kits listed below.
Grid End Plate Flange End
Plate Mud-In End Plate
8
Remove lens by gently pressing on the center of
the lens and inserting a screwdriver between the
lens and the housing.
12
Remove the (4) torx screws retaining the existing
end plate. Install the new end plate using the
new torx screws and reinstall the lens.
**IMPORTANT**
-RK6HPL Kit: End Plates are designed to be a direct replacement and cannot be used to change the mounting
type.
One Lithonia Way, Conyers, GA 30012 • Tel: 800-705-SERV (7378) • Website: https://acuitybrands.com/