Acuity Controls nLight nPOD 2P User manual

AcuityBrands|OneLithoniaWay Conyers,GA 30012 Phone:[phone] www.acuitycontrols.com
©2014-2016AcuityBrandsLighting,Inc. Allrightsreserved. Rev.06/06/16 nPODM-2P 1 of 2
nPOD2P Example:nPOD2PWH
Series Color
nPOD2P Wallpod:2-ChannelOn/Off LowVoltage WH White
OVERVIEW
Lowvoltage 2-ChannelWallPodsarenLight-enableddualtoggleswitchesthat provideauserwith localon/
off controlof two channelswithin alighting zone.These singlegang decoratorstyle devices useinnovative
nger-touch control instead of mechanical push-buttons or rockers. WallPods communicate with other
nLight devicesvia aCAT-5e cablethat connectsto oneof its twoRJ-45 connectors.A2-ChannelWallPod can
signal two relays located within nLight power packs and/or line voltage sensors to provide toggle switch
operationof two lighting circuits.
FEATURES
• Communicates w/ nLight network
• Finger-touchcontrol
• Remotely congurable/upgradable
• Two On/Off buttonsper unit
• Multipleswitchbroadcastchannels
ORDERING INFORMATION
CatalogNumber: Date: Project:
SPECIFICATIONS
Size: 2.74”Hx 1.68”Wx1.63”D
Weight: 2oz
Mounting: Singlegangswitch boxorlow voltagering
Network connection: (2) RJ45 ports
Power consumption: <3mA
Dimming load: Sinks < 20mA; ~40 Ballasts @ .5mA each
Wires: None
nPOD 2P
Wallpod: 2-Channel
On/Off Low Voltage
Warranty
Three-yearlimitedwarranty.Completewarrantyterms locatedat:
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Note:Actual performancemay differas aresult of end-userenvironment andapplication.
Specications subject to change without notice.

AcuityBrands|OneLithoniaWay Conyers,GA 30012 Phone:[phone] www.acuitycontrols.com
©2014-2016AcuityBrandsLighting,Inc. Allrightsreserved. Rev.06/06/16 nPODM-2P 2 of 2
WIRING
• MountWallPodusingholes thatalignwithstandardsinglegangswitch boxor
lowvoltagering.
• Connectgreenscrewto ground.
• AccessRJ-45 portsbyslidingtrapdoorup.
• Insert CAT-5 cable(s) through opening and route out through cutouts in rear of
WallPod.
• Secure cable(s) by sliding trapdoor back into orignal place
• Interconnectunit withothernLightdevices inlightingzoneusing CAT-5cables.
• Oncepoweris receivedviaCAT-5connection,alldevicesin zonewill
automaticallybeginfunctioning togetheraccordingto eachdevice’s defaults.
Power to WallPod device is provided via the CAT-5e connection to an nLight power pack/supply or Bridge. T568B pin/pair assignment is recommended for
allCAT-5ecables.
SLIDE
TO RJ-45 PORT
TO RJ-45 PORT
CAT-5
CAT-5
ON/OFF
TYPICAL WIRING
3-WAY CONFIGURATION WIRING
INSTALLATION
nPP16
LOAD 1
CAT-5
CAT-5
CAT-5C AT-5
120 V
277 V
-
-
BLK
ORN
nPP16
120 V
277 V
-
-
BLK
ORN
GROUND
LOAD 2
nPP16
CAT-5
LOAD 1
CAT-5
CAT-5
120 V
277 V
-
-
BLK
ORN
nPP16
CAT-5
LOAD 2
120 V
277 V
-
-
BLK
ORN
CAT-5
GROUND
CAT-5
CAT-5
GROUND
CAT-5
LOAD 1
LOAD 2
Attention! Only use non-booted CAT5e cables.