SignaMax 065-7528 User manual

User‘s Guide
8 port Nway Fast Ethenet
Web Smart Switch
Model:065-7508

1 SIGNAMAX LLC • www.signamax.eu
Web Smart Switch
Configure
Please follow the steps to configure this Web Smart switch.
Step 1:
Use a twisted pair cable to connect this switch to your PC.
Step 2:
Set your PC’s IP to 192.168.2.xx.
Step 3:
Open the web browser (like IE…), and go to 192.168.2.1 site, and then you will
see the login screen.
ID and the password: admin

2 SIGNAMAX LLC • www.signamax.eu
Step 4: After the authentication procedure, the home page shows up.
Select one of the configurations by clicking the icon.
- Administrator
- Port Management
- VLAN Setting
- QoS Setting
- Port Security
- Logout

3 SIGNAMAX LLC • www.signamax.eu
Administrator: Authentication
Configuration
1. Change the user name and the password.
2. Click “Update” to confirm the new change.
3. Turn off the power and reset this switch.
4. After resetting, turn on the switch for the new change.
Now, you can use the new user name and the password.

4 SIGNAMAX LLC • www.signamax.eu
Administrator: System IP Configuration
1. Change the IP address: type the new IP address or select DHCP IP
configuration.
2. Click “Update” to confirm the new change.
“Setting Process OK!!” will be shown on the screen.
3. Turn off the power and reset this switch.
4. After resetting, turn on the switch for the new change.
Now, the setting of “System IP Configuration” is finished.

5 SIGNAMAX LLC • www.signamax.eu
Administrator: System Status
It MAC address and system version will be shown on the screen.
1. Change the new comment of this switch by typing the new comment.
2. Click “Update” to confirm the new change.

6 SIGNAMAX LLC • www.signamax.eu
Administrator: Load Default Setting to EEPROM
1. Click “Load” to back to the factory default setting.
2. Turn off the power and reset this switch.
3. After resetting, turn on the switch for the new change.
Now, the default is loaded.

7 SIGNAMAX LLC • www.signamax.eu
Administrator: Firmware Update
Follow the instruction on the screen to update the new firmware.
Please contact with your sales agents to get the latest firmware
information.
.

8 SIGNAMAX LLC • www.signamax.eu
Port Management: Port Control Configuration
Select the “Port No.” - configure the mode below:
1. “Link Capability” – Auto-Nego. or 100M or 10M mode.
2. “Duplex” - select the port to full or half-duplex mode.
3. “Tx & Rx” - enable/disable Tx & Rx capability of the
port.

9 SIGNAMAX LLC • www.signamax.eu
Port Management: Bandwidth Control
Select the “Port No.” - configure the mode below:
1. “TX Rate” : set the maximum transmission rate of this
selected port and choose the full speed or in
128K/256K/512K/1M/2M/4M/8M speed.
2. “RX Rate” : set the maximum receiving rate of this selected
port and choose full speed or in
128K/256K/512K/1M/2M/4M/8M speed.

10 SIGNAMAX LLC • www.signamax.eu
Port Management: Broadcast Storm Control
1. “Setting” : tick the “Enable” to function the “Broadcast Storm
Control”.
2. Click “Update” to confirm the setting.
Now, the setting of “Broadcast Storm Control” is finished.

11 SIGNAMAX LLC • www.signamax.eu
Port Management: Max Packet Length
1. Select the maximum packet length setting, 1536 byte or 1552
byte of this switch.
2. Click “Update” to confirm the setting.
Now, the setting of “Max Packet Length” is finished.

12 SIGNAMAX LLC • www.signamax.eu
Port Management:POE Configuration
Remote access and monitor the attached PD (Powered Device) status by
using Enable/Disable function.
1. Enable: POE of the port is able to supply power to the attached PD
(Powered Device)
2. PSE Current & Minimum Output Power: The status of
the port current and minimum output power.
3. POE class: each POE port will detect the class of the attached PD
(Powered Device)
4. Click “Update” to confirm and finish the setting.
Now, the setting of “POE Configuration” is finished.

13 SIGNAMAX LLC • www.signamax.eu
VLAN Setting: Group VLAN Setting
There are 4 VLAN groups, 01, 02, 03, 04, can be used.
1. Select a group, and then click the port number which you
want to put it into the selected VLAN group.
2. Click “Update” to confirm and finish the setting.
Now, the setting of “VLAN Setting” is finished.

14 SIGNAMAX LLC • www.signamax.eu
VLAN Setting: Multi to 1 Setting
This is a special design for easily setting the switch VLAN into “VLAN Per
Port“.
1. Choose “Destination Port No”.
2. Choose “Disable Port”
3. Click “Update” to confirm and finish the setting.
After this setting, all ports can only connect to the destination port.

15 SIGNAMAX LLC • www.signamax.eu
QoS Setting: Class of Service Configuration
You can set QoS mode of per port by different bases.
1. “Port Base” - select the port which you want to
configure as high priority. It means the packet of the port
will be firstly transmitted.
2. “VLAN Tag/IP/DS” - select the port which you want to
configure as packets. It means the
packet with special Tag/IP will be
firstly transmitted.
3. Click “Update” to confirm and finish the setting.

16 SIGNAMAX LLC • www.signamax.eu
QoS Setting: High Priority Queue Configuration
You can select WRR low weight 1/4 or 1/8.
Click “Update” to confirm and finish the setting.

17 SIGNAMAX LLC • www.signamax.eu
QoS Setting: Customization Diffserv
Please follow the instruction on the screen to update the setting.

18 SIGNAMAX LLC • www.signamax.eu
Port Security
1. Enable: allow the packet which has this MAC address to
activate on the port. The port will record the first receiving source
MAC address as the security MAC address.
2. Click “Update” to confirm and finish the setting.
Logout: You can click “Logout” to logout.