ADEMCO Vista-10P Operating instructions

9,67$3
3URJUDPPLQJ*XLGH
ON OFF
1
OFF
4
MAX
7
INSTANT
READY
2
AWAY
5
TEST
8
CODE
0
3
STAY
6
BYPASS
9
CHIME
#
ARMED
READY
1
OFF
4
MAX
7
INSTANT
READY
2
AWAY
5
TEST
8
CODE
0
3
STAY
6
BYPASS
9
CHIME
#
ARMED
READY
®
K0735PRV1 9/02

– 2–
TO ENTER PROGRAMMING MODE:
Local programming requires the use of an alpha keypad connected to the keypad terminals on the control.
A. POWER UP, then depress [✱] and [#] both at once, within 50 seconds of powering up )if ✱98 was used to exit previously, this method
must be used to reenter program mode). OR
B. Initially, key: Installer Code (4 + 1 + 1 + 2) plus 8 + 0 + 0.
Data Field Programming Procedures
Task Procedure
Go to a Data Field Press [∗] + [Field Number], followed by the required entry.
Entering Data When the desired field number appears, simply make the required entry. When the last entry for a field is entered,
the keypad beeps three times and automatically displays the next data field in sequence.
If the number of digits that you need to enter in a data field is less than the maximum digits available (for example,
the phone number fields *41, *42), enter the desired data, then press [∗] to end the entry. The next data field is
displayed.
Review a Data Field Press [#] + [Field Number].
Data will be displayed for that field number. No changes will be accepted in this mode.
Deleting an Entry Press [∗] + [Field Number] + [∗]. (Applies only to fields ∗40–*46, *94, and pager programming fields)
Interactive Menu Mode Programming (∗56, ∗57, ∗58, ∗79, ∗80, ∗81, ∗82)
See respective sections in this document for programming procedures.
Press [✱]+[Interactive Mode No.] (for example, ✱56). The alpha display keypad will display the first of a series of prompts.
Interactive Menu Mode Used to Program
✱56 Zone Programming Zone characteristics, report codes, alpha descriptors, and serial numbers for RF trans.
✱57 Function Key Programming Unlabeled keypad keys (known as ABCD keys) for special functions
✱58 Zone Programming Same options as *56 mode, but with fewer prompts. Intended for those familiar with
(Expert mode) this type of programming, otherwise *56 mode is recommended.
✱79 Output Device Mapping Assign module addresses and map individual relays/powerline carrier devices
✱80 Output Programming 4204 Relay modules, Powerline Carrier devices, or on-board triggers
✱81 Zone List Programming Zone Lists for relay/powerline carrier activation, chime zones, pager zones, etc.
✱82 Alpha Programming Zone alpha descriptors
INITIALIZE DOWNLOAD and RESET DEFAULTS
✱96 Initializes download ID and subscriber account number.
✱97 Sets all data fields to original factory default values.
TO EXIT PROGRAMMING MODE:
✱98 Exits programming mode and
prevents
re-entry by: Installer Code + 8+ 0+ 0. If ✱98 is used to exit programming mode,
system must be powered down, and method A above used to enter the programming mode.
See field *88 for other *98 Program mode lockout options.
✱99 Exits programming mode and
allows
re-entry by: Installer Code + 8+ 0 + 0or method A above.
Special Messages
OC = OPEN CIRCUIT (no communication between Keypad and Control).
EE or ENTRY ERROR = ERROR (invalid field number entered; re-enter valid field number).
After powering up, AC, dI (disabled) or Busy Standby and NOT READY will be displayed after approximately 4 seconds. This will revert to
a “Ready”message in approximately 1 minute, which allows PIRS, etc. to stabilize. You can bypass this delay by pressing [#] + [0].
If E4 or E8 appears, more zones than the expansion units can handle have been programmed. The display will clear after you correct the
programming.
Table of Device Addresses
This Device Uses Address Reports as†† Enabled By…
RF Receiver 00 100 *56 zone programming: input device type entry
Long Range Radio 03 103 automatic if output to long range radio field *29 enabled
4286 Voice Module 04 104 automatic if phone module access code field *28 enabled
4204 Relay Module 12 112 *79 output device programming: entered at device address prompt:
Keypads:
keypad 1
keypad 2
keypad 3
keypad 4
keypad 5
keypad 6
keypad 7
keypad 8
16
17
18
19
20
21
22
23
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
data field programming as listed below:
always enabled, all sounds enabled.
data field *190
data field *191
data field *192
data field *193
data field *194
data field *195
data field *196
5800TM Module 28 n/a automatic
†† Addressable devices are identified by “1”plus the device address when reporting. Enter report code for zone 91 to enable addressable device
reporting (default = reports enabled). See field *199 for addressable device (ECP) 3-digit/2-digit identification keypad display options.

–3–
352*5$00,1*)250
Entry of a number other than one specified will give unpredictable results. Values shown in brackets are factory defaults.
Field Title / Valid Entries Programmed Values
SYSTEM SETUP
∗20 Installer Code [4112] | | |
4 digits, 0–9. Can perform all system functions except
cannot disarm unless it is used to arm system.
∗21 Quick Arm Enable [0]
0 = no quick arm; 1 = allow quick arm (with [#] key)
∗22 RF Jam Option [0]
0 = no RF Jam detection
1 = send RF Jam report upon detection of RF jamming
signal UL: must be 1 if wireless devices are used
∗23 Quick (Forced) Bypass [0]
0 = no quick bypass UL: must be “0”
1 = allow quick bypass (code + [6] + [#] )
∗24 RF House ID Code [00] |
00 = disable all wireless keypad usage
01–31 = house ID for 5827, 5827BD or 5804BD keypad
∗26 Chime By Zone [0]
0 = no (chimes on fault of any entry/exit or perimeter zone
when chime mode on);
1 = use zone list (chimes on fault of specific zones
programmed in relay zone list 3 when Chime mode on;
use *81 Menu mode to select zones)
∗28 Access Code For Phone Module [00] |
00 = disable; UL: must be “00”for UL Commercial Burg. inst.
1st digit: enter 1–9;
2nd digit: enter # + 11 for "✱", or # + 12 for "#".
∗29 Long Range Radio Output [0]
0 = not using LORRA; 1 = using LORRA output
ZONE SOUNDS AND TIMING (✱31 –✱39)
∗31 One Audible Alarm Per Zone [0]
0 = no UL: must be “0”; 1 = yes
∗32 Fire Alarm Sounder Timeout [0]
0 = sounder stops at timeout programmed in field ∗33
1 = no sounder timeout UL: must be “1”for fire install.
∗33 Alarm Sounder (Bell) Timeout [1]
0 = none; 1 = 4 min; 2 = 8 min; 3 = 12 min; 4 = 16 min;
UL: For residential fire alarm installation, must be set for a minimum
of 4 min (option 1); for UL Commercial Burglary installations, must
be minimum 16 min (option 4)
∗34 Exit Delay [60] |
00 - 96 = 0 - 96 secs; 97 = 120 secs
SIA Installations: minimum exit delay is 45 seconds
UL: see inst. instr. for requirements.
∗35 Entry Delay #1 (zone type 01) [30] |
00 - 96 = 0 - 96 seconds
97 = 120 seconds SIA Installations:
98 = 180 seconds minimum entry delay is
99 = 240 seconds 30 seconds
For UL Residential Burglary Alarm installations, must be set for a
maximum of 30 seconds; entry delay plus dial delay should not
exceed 1 min. For UL Commercial Burglar Alarm, total entry delay
may not exceed 45 seconds.
∗36 Entry Delay #2 (zone type 02) [30] |
See *35 Entry Delay 1 above for entries.
∗37 Audible Exit Warning [1]
0 = no; 1 = yes
SIA Installations: must be enabled (enter 1)
∗38 Confirmation Of Arming Ding [0]
0 = no ding
1 = confirmation ding after arming system
2 = ding after arming from RF button or RF keypad only
UL: must be “1”for UL Commercial Burglar Alarm inst.
∗39 Power Up In Previous State [1]
0 = always power-up in a disarmed state
1 = assume the system status prior to power down
UL: must be “1”
DIALER PROGRAMMING
Enter the number of digits shown. Do not fill unused spaces. Enter
0–9; #+11 for '✱'; #+12 for '#'; #+13 for a 2-second pause. If fewer
than the maximum digits entered, exit the field by pressing [✶]. The
next field number is displayed.
∗40 PABX Access Code | | | | |
Enter up to 6 digits. To clear entries, press ✱40✱.
If call waiting used, enter “∗(#+11) 70”plus “# + 13”(pause).
∗41 Primary Phone No.
| | | | | | | | | | | | | | | | | | |
∗42 Second Phone No.
| | | | | | | | | | | | | | | | | | |
Enter up to 20 digits. To clear entries, press ✱41✱or ✱42✱
respectively.
NOTE: Entry of a number other than one specified will give
unpredictable results.
For fields *43- *46: Enter 0–9; #+11 for B; #+12 for C; #+13 for D; #+14 for E;
#+15 for F. Enter [✱]as the fourth digit if a 3-digit account number (for 3+1
dialer reporting format) is used. Enter 0 as the first digit of a 4-digit account
number for Nos. 0000-0999. Exit field by pressing ✱(and press next field
number) if only 3 digits are used. E.g., For Acct. B234, enter:
#+11| 2 | 3 | 4
∗43 Primary Subs. Acct. No.
| | | / | | | | | [FFFF] Enter 4 or 10 digits,
depending on selection in *48 Report Format. See box
above for entries. To clear entries, press *43*.
∗44 Secondary Subs. Acct. No.
| | | / | | | | | [FFFF] See *43. To clear, press
*44*.
∗47 Phone System Select [1]
DIALING NOT On WATS LINE USING WATS LINE
Pulse Dial 0 2
Tone Dial 1 3
∗48 Report Format [77]
0 = 3+1, 4+1 ADEMCO L/S STANDARD Primary Second
1 = 3+1, 4+1 RADIONICS STANDARD
2 = 4+2 ADEMCO L/S STANDARD
3 = 4+2 RADIONICS STANDARD
5 = 10-digit ADEMCO CONTACT ID®REPORTING
6 = 4+2 ADEMCO EXPRESS
7 = 4-digit ADEMCO CONTACT ID®REPORTING
8 = 3+1, 4+1 ADEMCO L/S EXPANDED
9 = 3+1, 4+1 RADIONICS EXPANDED

–4–
∗49 Split/Dual Reporting [0]
0 = Standard/Backup reporting only (all to primary unless fail)
Primary Phone No. 2nd Phone No.
1 = Alarms, Restore, Cancel Others
2 = All except Open/Close, Test Open/Close, Test
3 = Alarms, Restore, Cancel All
4 = All except Open/Close, Test All
5 = All All
∗50 Burglary Dialer Delay [2]
0 = no delay UL: must be “0”
1 = 15 seconds SIA Installations: delay
2 = 30 seconds must be minimum of
3 = 45 seconds 30 seconds
∗53 SESCOA/Radionics Select [0]
0 = Radionics (0-9, B-F), and all formats other than SESCOA
1 = SESCOA (0-9 only reporting)
∗54 Dynamic Signaling Delay [0]
Delay selectable from 0 to 225 secs in 15-sec increments.
0 = no delay (both signals sent),
1 = 15 secs,
2 = 30 secs, etc
UL: Grade AA must be “0;”Grade A must be “15”max
∗55 Dynamic Signaling Priority [0]
0 = Primary Dialer first; 1 = Long Range Radio first.
For UL Commercial Burglary installations that use a DACT
and LRR, this field must be “0”.
∗56 -*58 Menu Modes (see page 2 for description)
PROGRAMMING SYSTEM STATUS, & RESTORE REPORT
CODES (✱59 –✱76, & ✱89):
For 3+1 or 4+1 Standard Format: Enter a code in the
first
box: 1–
9, #+10 for 0, #+11 for B, #+12 for C, #+13 for D, #+14 for E, #+15
for F.
A 0 (
not
#+10) in the
first
box will disable a report. A 0 (
not
#+10) in
the
second
box will result in automatic advance to the next field.
For Expanded or 4+2 Format: Enter codes in
both
boxes (1st and
2nd digits) for 1–9, 0, or B–F, as described above.
A 0 (
not
#+10) in the
second
box will eliminate the expanded
message for that report. A 0 (
not
#+10) in
both
boxes will disable
the report.
For Ademco Contact ID®Reporting: Enter any digit (other than 0)
in the
first
box, to enable zone to report (entries in the
second
boxes
are ignored).
A 0 (
not
#+10) in the
first
box disables the report.
UL: see installation instructions for requirements
SYSTEM STATUS REPORT CODES
∗59 Exit Error Report Code [0]
∗60 Trouble Report Code [00] |
∗61 Bypass Report Code [00] |
∗62 AC Loss Report Code [00] |
∗63 Low Bat Report Code [00] |
∗64 Test Report Code [00] |
Use Scheduling mode to set periodic test reports or use the
following key commands to set schedule 2 to the stated
repeat option (first test report sent 12 hours after command):
installer code +[#] + [0] + 0 = test report sent every 24 hours
installer code +[#] + [0] + 1 = test report sent once per week
installer code +[#] + [0] + 2 = test report sent every 28 days
∗65 Open Report Code [0]
∗66 Arm Away/Stay Rpt Code [0,0]
Away Stay
∗67 RF Trans. Low Bat Report Code [00] |
UL: must be enabled if wireless devices are used
∗68 Cancel Report Code [00] |
RESTORE REPORT CODES
∗70 Alarm Restore Rpt Code [0]
∗71 Trouble Restore Rpt Code [00] |
∗72 Bypass Restore Rpt Code [00] |
∗73 AC Restore Rpt Code [00] |
∗74 Low Bat Restore Rpt Code [00] |
∗75 RF Trans. Lo Bat Rst Rpt Code [00] |
UL: must be enabled if wireless devices are used
∗76 Test Restore Rpt Code [00] |
OUTPUT AND SYSTEM SETUP
∗77 Daylight Savings Time
Start\End Month [4][10] |
0 = Disabled
1-9 = January-September (1 = Jan, 2 = Feb, etc)
#+10 = October; #+11 = November; #+12 = December
∗78 Daylight Savings Time
Start\End Weekend [1][5] |
0 = disabled, 1 = first, 2 = second, 3 = third
4 = fourth, 5 = last, 6 = next to last, 7 = third to last
∗79 -*82 Menu Modes (see page 2 for description)
∗84 Auto Stay Arm [1]
0 = no, 1 = yes, auto stay arm enabled
∗85 Cross Zone Timer
This option not for use in UL installations. [0]
0 = 15 seconds 6 = 2-1/2 min #+12 = 8 min
1 = 30 seconds 7 = 3 min #+13 = 10 min
2 = 45 seconds 8 = 4 min #+14 = 12 min
3 = 60 seconds 9 = 5 min #+15 = 15 min
4 = 90 seconds #+10 = 6 min
5 = 2 minutes #+11 = 7 min
(assign cross zones on zone list 4, with *81 Menu mode)
∗86 Cancel Verify Keypad Display [1]
0 = no, 1 = yes
∗87 Misc. Fault Delay Time [0]
(used with Configurable Zone Type “digit 6”)
0 = 15 seconds 6 = 2-1/2 min #+12 = 8 min
1 = 30 seconds 7 = 3 min #+13 = 10 min
2 = 45 seconds 8 = 4 min #+14 = 12 min
3 = 60 seconds 9 = 5 min #+15 = 15 min
4 = 90 seconds #+10 = 6 min
5 = 2 minutes #+11 = 7 min
UL: may only be used on non-burglar alarm/ non-fire alarm zones
when used in fire and/or UL burglar alarm installation
∗88 Program Mode Lockout Options [0]
0 = standard *98 installer code lockout
(reentry only by [∗] + [#] within 50 seconds after power up)
1 = lockout [∗] + [#] reentry after *98 exit
2 = not used
3 = lockout all local programming after *98 exit (reentry via
downloader only)

–5–
∗89 Event Log Full Report Code [00] |
See box above *59 for report code entries.
∗90 Event Log Enables [3]
NOTE
:
System messages are logged when any non-zero
selection is made.
0 = None; 1 = Alarm/Alarm Restore
2 = Trouble/Trouble Restore;
4 = Bypass/Bypass Restore;
8 = Open/Close.
Example:
To select “Alarm/Alarm Restore”,
and “Open/Close”, enter 9 (1 + 8); to select all, enter #15.
∗91 Option Selection [8]
Multiple choice example: for AAV (4) + Exit Delay restart (8) enter # + 12.
0 = None
4 = AAV UL: must use ADEMCO UVCM module
8 = Exit Delay Restart/Reset UL: must be disabled
SIA Installations: Exit Delay should be enabled.
∗93 Reports in Armed Period Per Zone [1]
(
Also known as Swinger Suppression)
0 = Unlimited Reports; 1 = 1 report; 2 = 2 reports
UL: must be “0”
DOWNLOAD INFORMATION
∗94 Download Phone No.
| | | | | | | | | | | | | | | | | | |
Enter up to 20 digits, 0–9; #+11 for '✱'; #+12 for '#'; #+13 for a
2-second pause. Do not fill unused spaces. If fewer than 20
digits, exit field by pressing ✱. To clear entries, press ✱94✱.
UL: downloading may be performed only if a technician is at
the site.
∗95 Ring Count For Downloading [15]
NOTE: Do not enter “0”if using 4285/4286 Phone Module.
0 = Disable Station Initiated Download;
1–14 = number of rings (1–9, # +10 =10, # +11 =11,
# +12 =12, # +13 =13, # +14 =14);
15 = answering machine defeat (# +15 =15).
∗96, *97 Initialize/Reset Defaults
(
These are commands, not data fields. See page 2)
∗98, *99 Exit Commands
(
These are commands, not data fields. See page 2)
PAGER OPTIONS
∗160 Pager 1 Phone No.
| | | | | | | | | | | | | | | | | | |
Enter up to 20 digits. 0–9; #+11 = '✱'; #+12 = '#';
#+13 = 2-second pause.
∗161 Pager 1 Characters
| | | | | | | | | | | | | | |
Enter the optional prefix characters, up to 16 digits.
0–9; #+11 = '✱'; #+12 = '#'; #+13 = 2-second pause.
∗162 Pager 1 Reporting Options [0]
Select from the following options:
0 = no reports sent
1 = Open/closes all users
4 = All alarms and troubles
5 = All alarms / troubles, and open/closes for all users
12 = Alarms / troubles for zones entered in zone list 9
13 = Alarms / troubles for zones entered in zone list 9, and
open/closes for all users
∗172 Pager Delay Option For Alarms [3]
0 = none, 1 = 1 minute, 2 = 2 minutes, 3 = 3 minutes
This delay is for ALL pagers in the system.
NOTE: The delay does not reset for new alarms occurring
while an existing pager delay is in progress.
MISCELLANEOUS SYSTEM FIELDS
∗177 Device Duration 1, 2 [0] [0]
(used in *80 Menu mode-Device Actions 5/6) 1 2
0 = 15 seconds 6 = 2-1/2 min #+11 = 7 min
1 = 30 seconds 7 = 3 min #+12 = 8 min
2 = 45 seconds 8 = 4 min #+13 = 10 min
3 = 60 seconds 9 = 5 min #+14 = 12 min
4 = 90 seconds #+10 = 6 min #+15 = 15 min
5 = 2 minutes
∗181 60 Hertz AC Operation [0]
0 = 60 Hz; 1 = 50 Hz
CONFIGURABLE ZONE TYPE OPTIONS
∗182 Configurable Zone Type 90
1 2 3 4 5 6 7 8 9 10
Enter the appropriate value for each entry, 1-10, based on
the charts provided on the next page. Each entry is the
sum of the values of its selected options
(0-9, #+10=10, #+11=11, #+12=12, #+13=13, #+14=14,
#+15=15).
UL: Do not configure zones as a fire alarm or UL burglar
alarm zone.
∗183 Zone Type 90 Report Codes
IMPORTANT: Use existing Contact ID®codes, if
appropriate, or define unique codes in CID code range
750-789. See note in installation instructions.
90 ALARM ID: XXX
TROUBLE ID: XXX
Enter the desired 3-digit Contact ID®report codes for
alarms and troubles occurring on zones assigned to this
zone type. Enter the codes sequentially (all 6 digits). When
entering digits, [#] moves cursor back, [∗] moves forward.
Press [∗] when done to continue.
KEYPAD OPTIONS
(Options for keypad 1, address 16 are set by the factory and cannot
be changed.)
NOTE: Each keypad must be assigned a unique address.
Keypads programmed with the same address will give
unpredictable results.
∗190 Keypad 2 Device Address 17 [0] [0]
Enable: 0 = disabled; 1 = enabled Enable Sound
Sound: 0 = no suppression
1 = suppress arm/disarm and E/E beeps
2 = Suppress chime beeps only
3 = suppress arm/disarm, E/E, and chime beeps
Enable Sound
∗191 Keypad 3 Device Address 18 [0] [0]
∗192 Keypad 4 Device Address 19 [0] [0]
∗193 Keypad 5 Device Address 20 [0] [0]
∗194 Keypad 6 Device Address 21 [0] [0]
∗195 Keypad 7 Device Address 22 [0] [0]
∗196 Keypad 8 Device Address 23 [0] [0]
∗197 Exit Time Display Interval [0]
0 = no display; 1-5 = seconds between display refresh
∗199 ECP Fail Display [0]
0 = 3-digit display (“1”+ device address)
1 = 2-digit fixed-display as “91”

–6–
Configurable Zone Types Worksheets
Configurable zone type 90 can be programmed via downloader software or from a keypad using data fields*182-
*183.
Programming Configurable Zone Type options involves making 10 entries in data field *182, where each entry
represents the sum of the values of the various options shown in the tables below. Use field *183 to program a
Contact ID report code for this zone type.
ENTRY 1 (See note 4 for RF zones) ENTRY 2 (See note 4 for RF zones)
Response when system disarmed and zone is:
Intact EOL
RF zone normal
Open
RF zone N/A
Shorted
RF zn off-normal
Auto
Restore Vent Zone
0 = normal
1 = alarm
2 = trouble
3 = fault
0 = normal
4 = alarm
8 = trouble
12 = fault
0 = normal
1 = alarm
2 = trouble
3 = fault
0 = no
4 = yes 0 = no 8 = yes
Entry 1 = EOL + Open Entry 2 = Short + auto restore + vent zone
ENTRY 3 (See note 4 for RF zones) ENTRY 4 (See note 4 for RF zones)
Response when armed STAY and zone is:
Intact EOL
RF zone normal
Open
RF zone N/A
Shorted
RF zn off-normal
Byp. when
disarmed Byp. when armed
0 = normal
1 = alarm
2 = trouble
3 = fault
0 = normal
4 = alarm
8 = trouble
12 = fault
0 = normal
1 = alarm
2 = trouble
3 = fault
0 = no
4 = yes
0 = no
8 = yes
Entry 3 = EOL + Open Entry 4 = Short + byp. disarmed + byp. armed
ENTRY 5 (See note 4 for RF zones) ENTRY 6 (See note 4 for RF zones)
Response when armed AWAY and zone is:
Intact EOL
RF zone normal
Open
RF zone N/A
Shorted
RF zn off-normal
Dial Delay
(see field *50) Fault Delay (see field *87)
0 = normal
1 = alarm
2 = trouble
3 = fault
0 = normal
4 = alarm
8 = trouble
12 = fault
0 = normal
1 = alarm
2 = trouble
3 = fault
0 = no
4 = use delay
0 = no
8 = use delay
see note 1
Entry 5 = EOL + Open Entry 6 = Short + dial delay + fault delay
ENTRY 7 ENTRY 8
Display Faults Power Reset/
Verification Use Entry Delay 1/2 Use Exit Delay Respond as Interior Type
0 = show alarms
when armed
& disarmed
1 = don’t show
alarms when
armed (show
alarms, trbles,
faults when
disarmed)
3 = never show
any alarms,
trbles, faults
0 = no
4 = power reset
after fault
(by code + OFF)
12 = verification
(see zone
type 16)
0 = no
1 = delay 1
2 = delay 2
0 = no
4 = use exit
delay
0 = no
8 = yes
see note 2
Entry 7 = fault display + power
reset/verification Entry 8 = entry delay 1/entry delay 2 + exit delay + interior zone type
ENTRY 9 ENTRY 10
Alarm Sounds Use Bell
Timeout Respond as Fire Zone Trouble Sounds Chime when Chime Mode On
0 = none
1 = steady
keypad
2 = steady bell
and keypad
3 = pulsing bell
and keypad
0 = no
4 = yes
see fields *32,
*33
0 = no
8 = yes
see zone type
09; see note 4
0 = none
1 = periodic
beep
2 = trouble
beeps
0 = no
4 = yes
Entry 9 = alarm sounds + bell timeout + fire zone Entry 10 = trouble sounds + chime
Entries for Fields *182
Entry Zone Type 90 (field *182)
1
2
3
4
5
6
7
8
9
10
To calculate the value for each entry:
Simply add the values of the selected options
in each of the entry’s columns (one option per
column). For example, to program Entry 2 for
“alarm response to short,”“auto restore on,”
but not a “vent zone,”enter 5 (“1”for alarm
short + “4”for auto restore yes + “0”for vent
zone no).
OPEN SHORTEDINTACT
EOL
ZONE-003-V0
Zone Conditions Represented
in Entries 1-6
NOTES:
1. Do not use the “fault delay”option with a
configurable zone type if it is set for an
entry or exit delay, otherwise
unpredictable results may occur.
2. To create an interior type zone, select
“respond as interior zone type”(entry 8,
interior type = yes), and set zone
response to “fault”in entries 3-4 to ensure
fault displays; do not set as “normal,”
“alarm,”or “trouble.”
3. Do not set fire zones to respond as a
“fault”(entries 1-6), otherwise faults will
not display unless the [∗] key is pressed.
4. RF Zones: The “open”option in entries 1,
3, and 5 is not applicable for RF zones.
Use the “intact EOL”option for normal RF
zone conditions and “shorted”for off-
normal RF zone conditions.

–7–
*56 ZONE PROGRAMMING WORKSHEET [default shown in brackets]
Zone Zn Type Part. Report Hardwire
Type Rsp. Time Location
1 [01] [1] [EOL] [1]
2 [01] [1] [EOL] [1]
3 [03] [1] [EOL] [1]
4 [03] [1] [EOL] [1]
5 [03] [1] [EOL] [1]
6 [03] [1] [EOL] [1]
Zone Zn Type Part. Report Input Type Loop Serial No. Location
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
49 [1] [BR]
50 [1] [BR]
51 [1] [BR]
52 [1] [BR]
53 [1] [BR]
54 [1] [BR]
55 [1] [BR]
56 [1] [BR]
95 [00] N/A N/A N/A keypad [1] / [∗]
96 [00] N/A N/A N/A keypad [3] / [#]
99 [06] N/A N/A N/A keypad [∗] / [#]
∗56 ZONE PROGRAMMING MENU MODE (press *56 while in Program mode)
SETTO CONFIRM?
0 = NO 1 = YES We recommend that you select “yes”to confirm the programming of every transmitter.
If selected, a prompt appears after entering the serial and loop numbers to confirm each transmitter)
Enter Zn Num.
(00 = Quit) 10 Enter the zone number being programmed:
01-06 = wired zones; 09-24 = wireless zones; 49-56 = button zones
91 = addr. device report enable (Enter a report code for zone 91 to enable addressable device reporting.
92 = duress report enable (Enter a report code for zone 92 to enable duress reporting)
95, 96, 99 =emergency zones
00 to quit; [∗] to continue
Zn ZT P RC In: L
10 00 1 10 RF: 1
Summary Screen for the selected zone is displayed.
“IN: L”= input type and loop; “HW: RT”= basic wired zone configuration (EOL, NO, NC) and response time
[∗] to continue
10 Zone Type
Perimeter 03
Enter the desired ;zone type from the list below. If 00 is entered, Delete Zone ? is displayed.
00 = Not used 07 = 24-Hr Audible 20 = Arm–STAY*
01 = Entry/exit #1 08 = 24-Hr Aux 21 = Arm–AWAY*
02 = Entry/exit #2 09 = Fire 22 = Disarm*
03 = Perimeter 10 = Interior w/Delay 23 = No Alarm Resp*
04 = Interior Follower 12 = Monitor Zone 24 = Silent Burglary
05 = Trouble Day/Alarm Night 14 = Carbon Monoxide 77 = Keyswitch
06 = 24-Hr Silent 16 = Fire w/Verify 81 = AAV Monitor Zone
*5800 button-type transmitters only 90 = Configurable
10 Report Code
1st 01 2nd 00 10
Enter the report code for this zone, which consists of 2 hexadecimal digits, each in turn consisting of two
numerical digits. For example, for a report code of “10,”enter 01 and 00.
For Contact ID®, entering any non-zero entry as the first digit enables the report code for this zone.
1-9, #+10 for 0, #+11 for B, #+12 for C, #+13 for D, #+14 for E, #+15 for F
00 to disable;
[∗] to continue
02 HARDWIRE TYPE
EOL 0
This prompt appears only for zone numbers 01-06.
Enter the desired hardwire type:
0 = EOL; 1 = NC; 2 = NO
[∗] to continue
NOTES:
Zone Type: see chart on
page 11;
Hardwire Type (zns 1-6):
0 = EOL
1 = NC
2 = NO
Input Type:
3 = RF (zones 9-24)
4 = UR (zones 9-24)
5 = BR (zones 49-56)
Response Time:
0 = 10msec
1 = 350msec
2 = 700msec
3 = 1.2 sec
Reserved Zones
91 = addressable device
report enable/disable
default zone type =
[05].
92 = Duress report
enable/disable

–8–
02 Response Time
1
This prompt appears only for hard-wired zones 01-06 (zone 02 is used as an example in display).
Enter the desired response time for this zone:
0 = 10mSec; 1 = 350mSec; 2 = 700mSec; 3 = 1.2 seconds
[∗] to continue
10 INPUT TYPE
RF TRANS 3
This prompt is skipped for zones 1-6.
Select the desired input type for the transmitter zone being programmed (some transmitters have more than
one input loop, each requiring its own zone; e.g., a 5804's four inputs requires four zones).
3 = RF (supervised RF transmitter; sends fault, restore, and low-battery signals, and sends periodic check-
in signals; transmitter must stay within receiver's range)
4 = UR (unsupervised RF transmitter; sends fault, restore, and low-battery signals, but does not send
periodic check-in signals; transmitter may be carried off-premises)
5 = BR (unsupervised button type RF transmitter; sends fault and low battery signals when activated, does
not send restore or check-in signals; transmitter may be carried off-premises)
[∗] to continue
NOTES:
•For the built-in basic wired zones, the Input Device type is automatically displayed as HW and cannot be
edited.
10 INPUT S/N: L
A022-4064 1
For wireless transmitters, enroll the serial number and loop number.
1. a. Transmit two open/close sequences. If using a button-type transmitter, press and release the button
twice, but wait about 4 seconds before pressing the button the second time.
OR
b. Manually enter the 7-digit serial number printed on the label of the transmitter.
Press the [∗] key to move to the “L”position, then enter the loop number (see Loop Identification chart
on back cover).
If desired, you can press the [C] key to copy the previously enrolled serial number (used when
programming a transmitter with several input loops). The cursor moves to the loop number position.
c. To delete an existing serial number, enter 0 in the loop number field. The serial number will change to
0's. If 0 was entered in error, simply re-enter the loop number or press [#], and the serial number will
return to the display.
2. Press [∗] to continue. The system now checks for a duplicate serial/loop number combination.
10 INPUT S/N L
A022-4064 1
If the serial/loop number combination is not a duplicate in the system, a display showing the serial number
and loop number entry appears.
[∗] to continue
XMITTOCONFIRM
PRESS ✱TO SKIP
This prompt will only appear if you answered “Yes”at the “SET TO CONFIRM”prompt.
The system now enters a confirmation mode so that the operation of the actual programmed input can be
confirmed.
Activate the loop input or button that corresponds to this zone.
[∗] to continue
Entd A022-4063 1
Rcvd A022-4064 1
If the serial number transmitted does not match the serial number entered, a display similar to the one
shown appears. If the loop number does not match, it will also be displayed.
If so, activate the loop input or button on the transmitter once again. If a match is not obtained (i.e., summary
display does not appear), press the [#] key twice and then enter (or transmit) the correct serial number.
[∗] to continue
Zn ZT RC In: L
10 03 10 RF: 1s
If the serial number transmitted matches the serial number entered, the keypad will beep 3 times
and a summary display will appear, showing that zone's programming. Note that an “s”indicates
that a transmitter’s serial number has been enrolled.
[∗] to accept the zone information and continue
PROGRAM ALPHA?
0 = NO 1 = YES 0
If you want to program descriptors for the zone now, enter 1 (yes) and refer to the *82 Descriptor
Programming section for procedures.
To program descriptors later, enter 0 (no).
[∗] to continue
ENTER ZN NUM.
(00 = QUIT) 11
If 0 (No) was entered at the Program Alpha prompt, the system will return you to the ZONE NUMBER
prompt. Repeat these steps for each zone in the system.
When all zones have been programmed, enter 00 as the zone number to quit.
[∗] to continue
Wireless Key Predefined Default Templates
For 5804 Loop Function Zone Type For 5804BD Loop Function Zone Type
TEMPLATE 1 1 No Response 23 TEMPLATE 4 1 No Response 23
2 Disarm 22 2 No Response 23
3 Arm Away 21 3 Arm Away 21
4 No Response 23 4 Disarm 22
TEMPLATE 2 1 No Response 23 TEMPLATE 5 1 No Response 23
2 Disarm 22 2 Arm Stay 20
3 Arm Away 21 3 Arm Away 21
4 Arm Stay 20 4 Disarm 22
TEMPLATE 3 1 24-hour audible 7 TEMPLATE 6 1 24-hour audible 7
2 Disarm 22 2 Arm Stay 20
3 Arm Away 21 3 Arm Away 21
4 Arm Stay 20 4 Disarm 22

–9–
∗58 Expert Programming Mode Procedures (press ∗58 while in Data Programming mode)
SETTO CONFIRM?
0 = NO 1 = YES We recommend that you select “yes”to confirm the programming of every transmitter.
If selected, a prompt appears after entering the serial and loop numbers to confirm each transmitter)
Zn ZT RC HW: RT
01 09 10 EL 1
Zn ZT RC IN: L
10 –––: –
A summary screen will appear, showing zone 1’s currently programmed values.
Enter the zone number being programmed, then press [∗]. In this example, zone 10 is being entered
(see Zone Number prompt in *56 Menu Mode for zone numbers).
[D] = for assigning wireless key programming templates (see Wireless Key Programming Templates section
in i/i); lets you choose from a series of preset templates for easy programming of wireless key zones
00 = quit (when all zones have been programmed, press “00”to quit this menu mode)
[∗] to continue
Zn ZT RC IN: L
10 00 10 RF 1
A summary screen with the selected zone’s current programming appears.
Begin programming zone information as follows:
Enter Zone Type (ZT; see Zone Types listed in *56 Menu Mode “Zone Type”prompt), Report Code (RC), and
Input Device Type (IN)* sequentially (Loop Number (L) is entered at the next prompt).
•Use the [A] (Advance) and [B] (Back) keys on the keypad to move the cursor within the screen.
•Use the [C] key to copy the previous zones attributes.
* If HW (hardwired) or AW (Auxiliary) is entered for Input Device Type, the display will be similar to the
prompt shown, except that HW or AW will be under “IN”.
Press [∗] to save the programming and continue. If needed, press the [#] key to back up without saving.
For wireless devices (input types RF, UR, BR), continue to the serial number/loop number prompt.
For wired devices, return to the initial summary screen prompt to begin programming the next zone.
10 INPUT S/N: L
AXXX-XXX –
Zn ZT P RC In L
10 03 1 10 RF:1s
Manually enter the serial number (found on the transmitter label), by typing digits in the “X”locations, using
the [A] (advance) or [B] (back) keys as required.
OR
Transmit two open/close sequences. If using a button-type transmitter, press and release the button twice,
but wait about 4 seconds before pressing the button the second time.
If you want to copy the previous zone’s serial number, press the [C] key.
Press [∗] to advance to the loop number, then enter loop number.
Press [∗] to accept the existing serial and loop number and continue to the “Confirm”prompt described in
*56 Menu mode above.
If necessary, press [#] to back up and re-enter or edit the serial number.
If the serial number transmitted matches the serial number entered, the keypad will beep 3 times and a
summary display will appear, showing the programmed information for that zone.
Press [∗] to begin programming the next zone. See first “Summary Screen”prompt paragraph.
Wireless Key Programming Templates (press the [D] key from *58 Menu mode Summary Screen display)
This procedure programs the wireless keys, but a key is not active until it is assigned to a user number (see System Operation section,
assigning attributes command in the Installation Instructions).
TEMPLATE ?
1–6 1
Enter desired template number 1–6 (see chart on previous page).
Press [#] if you want to return to *58 Menu mode Summary Screen.
If necessary, press [#] to back up and re-enter template number.
Press [∗] to continue to template display.
L 01 02 03 04
T 23 22 21 23
The selected template is displayed.
Top line of display represents loop numbers, bottom line represents zone type assigned for each loop.
Press [∗] to accept template and continue.
ENTER START ZONE
00 = QUIT 36
The system will search for the highest available consecutive 4-zone group (the four zones in the case of the
5804 and 5804BD), and display the lowest zone number of the group.
If you want to start at a different zone, enter the zone desired, and press [∗]. If that zone number is
displayed, the system has the required number of consecutive zones available, beginning with the zone you
entered. If not, the system will again display a suggested zone that can be used.
If the required number of consecutive zones is not available at all, the system will display “00”.
Press [∗] to accept and continue.
INPUT S/N L
AXXX-XXXX –
Manually enter the serial number printed on the label for the wireless key or press and release the button to
transmit its serial number.
Press [∗] to accept the serial number. The system will check for duplicate.
If necessary, press the [#] key to back up without saving, and re-enter the serial number.
Use the [A] key to move forward within the screen, and the [B] key to move backward.
XMIT TO CONFIRM
PRESS ✱TO SKIP
If “Yes”was entered at the SET TO CONFIRM? prompt (first prompt following entry into the ∗58 Expert
Programming Mode), this display appears.
Confirm serial and loop numbers by activating the wireless key. Refer to the “Confirm”prompt described in
*56 Menu mode above for more information on confirming the serial number.
If the serial number transmitted matches the serial number entered, the keypad will beep 3 times and will
return you to the ENTER START ZONE NUMBER prompt to enter the starting zone for the next wireless key.
IMPORTANT: When confirmed, the key is not active until it is assigned to a user number (using the
assigning attributes command, attribute “4”). See System Operation section in Installation Instructions.
[∗] to skip confirm.

–10 –
*57 FUNCTION KEY PROGRAMMING
Option Function A B C D Comments
01 Paging
02 Time Display
03 Arm AWAY
04 Arm STAY
05 Arm NIGHT-STAY
06 Step Arming
07 Device Activation
Device:
08 Comm. Test
09 Macro Key
00 Emergency Keys: zone 95 zone 99 zone 96 paging
Personal Emergency n/a
Silent Alarm
n/a
Audible Alarm
n/a
Fire n/a
Emergency Keys: A = paired keys [1] / [∗] (zone 95); B = paired keys [∗] / [#] (zone 99); C = paired keys [3] / [#] (zone 96)
Start Function Key Programming mode by pressing ∗57 while in Data Programming mode.
Press Key to Pgm
0 = Quit 0
Press the desired function key, A-D.
NOTE: A key programmed as a function key is no longer available to be used as an end-user macro key or
panic key.
[∗] to continue
Key "A" Func
Zone 95 00
Enter the desired function for this key:
00 = For the Function key selected, the function will be as follows (system default):
If A selected = Zone 95 (emergency key, same as [1] [∗] pair)
If B selected = Zone 99 (emergency key, same as [∗] [#] pair)
If C selected = Zone 96 (emergency key, same as [3] [#] pair)
If D selected = Single-button paging
01 = Single-button paging (sends a 999-9999 message to pager)
02 = Display time
03 = Arm AWAY (reports as User 00 if closing reports are enabled)
04 = Arm STAY (reports as User 00 if closing reports are enabled)
05 = Arm NIGHT-STAY (reports as User 00 if closing reports enabled)
06 = Step Arming (arms STAY, then NIGHT-STAY, then AWAY)
07 = Output Device Command (for device programmed as system operation type 66 in *80 Menu Mode)
08 = Communication Test (sends Contact ID code 601)
09= Macro Key (defined by [#] [6] [6] command)
[∗] to continue; returns to key number prompt with the next function key letter displayed.
OUTPUT RELAYS WORKSHEET FOR ∗79, ∗80 and ∗81 (Applicable only if Relays are to be used)
∗79 RELAY MAPPING (Must program before using *80)
Output No. Module Addr. Pos (1-4) Description
01 12
02 12
03 12
04 12
17 On-Board Trigger 1: Norm output =
18 On-Board Trigger 2: Norm output =
Start Output Device Mapping by pressing *79 while in Data Programming Mode.
ENTER OUTPUT NO.
00 = QUIT xx
Enter the logical (or reference) relay number as used in the system.
01-04 = relays; 17-18 = on-board triggers (can be programmed for inverted output; see next prompt)
[∗] to continue
17 OUT NORM LOW
0 = NO 1 = YES 0
This prompt appears only for triggers 17 and 18.
0 = no (standard default); sets the trigger output level normally high
1 = yes; sets the trigger output normally low (can be used for resetting 4-wire smoke detectors by
connecting trigger wire to the negative power terminal of the smoke detector, selecting 1 at this prompt,
and setting as zone type 54, fire zone reset, in *80 Menu mode)
[∗] to return to Output Number prompt
XX OUTPUT TYPE
DELETE? 0 Enable or delete this output.
0 = delete this output number; 1 = enable output
[∗] to continue
XX MODULE ADDR
07-15 yy
Enter the module’s predefined address “12”(set the module’s DIP switches to “12”).
[∗] to continue
XX REL POSITION
1-4 zz Enter the actual (or physical) relay number, 1-4, with respect to the Relay Module upon which it is located.
[∗] to return to the Output Number prompt for programming the next device

–11 –
✱80 OUTPUT DEFINITIONS
Activation Type and Detail Event (for zone list/activated by)Output
Function
Number
1-12
Activated by
0=delete
1=zn list
2=zn type
3=zn no.
Zone List
(ZL)
1-8 = list
Zone Type
(ZT)
(see table
below)
Zone No.
(ZN)
00=none
01-06,
09-24
49-56
By Zone List
0 = restore
1 = alarm
2 = fault
3 = trouble
By Zone No.
0 = restore
1 = alrm/flt/trbl
Action
0 = off
1 = close 2 secs
2 = stay closed
3 = pulse
4 = toggle
5 = duration 1††
6 = duration 2††
Output
Number
1-4
17, 18
Device
Type
R = relay
T = trigger
1
2
3
4
5
6
7
8
9
10
11
12
ZONE TYPE/SYSTEM OPERATION –Choices for Zone Types are:
00 = Not Used 05 = Trouble Day/Alarm Night 10 = Interior w/Delay 24 = Silent Burglary
01 = Entry/Exit#1 06 = 24 Hr Silent 12 = Monitor Zone 77 = Keyswitch
02 = Entry/Exit#2 07 = 24 Hr Audible 14 = Carbon Monoxide 81 = AAV Monitor Zone
03 = Perimeter 08 = 24 Hr Aux 16 = Fire w/Verification 90 = Configurable
04 = Interior Follower 09 = Fire 23 = No Alarm Response
Choices for System Operation are:
20 = Arming–Stay 38 = Chime 52 = Kissoff
21 = Arming–Away 39 = Any Fire Alarm 54 = Fire Zone Reset
22 = Disarming (Code + OFF) 40 = Bypassing 58 = Duress
31 = End of Exit Time 41 = AC Power Failure 60 = AAV Trigger
32 = Start of Entry Time 42 = System Battery Low 66 = Function key†
33 = Any Burglary Alarm 43 = Communication Failure 67 = Bell Failure
36 = **At Bell Timeout*** 68 = Telco Line Fault
78 = Keyswitch Red LED†††
79 = Keyswitch Green LED†††
Start Output Definition mode by pressing ∗80 while in Data Programming mode.
Output Funct. #
(00 = Quit) 01
Enter the output function number to be defined
01-12 = output function number
[∗] to continue; 00 = exit
01 A E Trig
?00 0 0 –ZL=1
This screen displays a summary of the current output programming
A = Output Action; E = Triggering event; Trig = Trigger type
Question mark indicates the device shown has not been mapped. Use *79 Menu mode to map the device.
[∗] to continue
01 Activated By:
Zone List
Select where the initiating event for this output definition is to occur.
0 = delete (deletes the output function and any previous programming)
Delete? To delete this output definition, press 1.
0 = NO, 1 = YES If you do not want to delete this output,. press 0.
1 = zone list (go to “A”prompt); 2 = zone type (go to “B”prompt); 3 = zone number (go to “C”prompt)
[∗] to continue
“A”
01 Zn List
1
If zone list was selected, this screen appears. Otherwise skip to the next prompt.
Enter the desired zone list number associated with this output number:
01-08 = zone list (Do not use pager zone list 09 in output definitions)
Enter the zone list event that will activate this output:
Enter Event 0 = restore; 1 = alarm;
Alarm 1 2 = fault; 3= trouble
NOTE: For alarm, fault, and trouble, an event on ANY zone in the list activates the output, but ALL zones in
the list must be restored before the output is restored.
Press [∗] to continue and skip to the “Output Action”prompt.
“B”
01 Enter Zn type
Perimeter 03
If zone type was selected, this screen appears. Otherwise skip to the next prompt.
Enter the desired zone type for this output number. See list below *80 Worksheet for zone types.
Press [∗] to continue and skip to the “Output Action”prompt.
Note: In normal operation mode:
Code + # + 7 + NN Key Entry starts Device
Code + # + 8 + NN Key Entry stops Device
*** Or at Disarming, whichever occurs earlier.
†Use *57 Menu mode to assign the function key.
†† Duration is set in program field *177.
††† Device action not used for these choices.

–12 –
“C”
01 Enter Zn No.
12
If zone number was selected, this screen appears.
Enter the desired zone number associated with this output number.
Press [∗] to continue.
Enter the zone event that will activate this output.
01 Enter Event 0 = restore; 1 = alarm/fault/trouble
Restore 0
Press [∗] to continue to the “Output Action”prompt
01 Output Action
Close for 2 sec 1
Enter the desired device action as listed below.
0 = off 4 = Change Device State
1 = Close for 2 seconds 5 = Duration 1 (see data field *177)
2 = Close and Stay Closed 6 = Duration 2 (see data field *177)
3 = Continuous Pulse on & off (1 sec ON, 1 sec OFF)
Press [∗] to continue.
Enter Output No.
R02 02
Enter the device output number (programmed in *79 Menu Mode) you want associated with this output.
01-04 = output no.
17-18 = on-board triggers
Press [∗] to continue.
02 A E P TRIG
R02 1 1 3 ZL=1
A summary screen appears showing the programmed settings.
Press [∗] to return to output function number prompt.
✱81 ZONE LISTS
Record desired zone numbers below, noting that a list may include
any
or
all
of system's zone numbers.
List No. Used For…Contains These Zones…
01 General Purpose (GP)
02 General Purpose
03 Chime-by-Zone or GP
04 Cross Zones
05 Night-Stay Zones or GP
06 General Purpose
07 General Purpose
08 General Purpose
09 Zones activating pager
NOTES:
•Any list may include any or all of the system's zone numbers.
•A zone list can be assigned to more than one output relay.
•When creating zone list 4 for cross zoning, include only zones assigned to zone types 3, 4, or 5. Do not include zones that have delays
(entry/exit zones, interior w/delay) or 24-hour zones, as these zone types may produce unpredictable operation and may not function as
intended.
Start Zone List Program Mode by pressing ∗81 while in Data Programming mode.
Zone List No.
(00 = Quit) 01
Enter the Zone List Number to program (or 00 to end these entries).
01-09 = zone list number
[∗] to continue
01 Enter Zn Num.
(00 = Quit) 00
Enter each zone number followed by [∗] to add each zone to the zone list.
01-06 = wired zones; 09-24 = wireless zones; 49-56 = button zones
91 = addr. device report enable (Enter a report code for zone 91 to enable addressable device reporting.
92 = duress report enable (Enter a report code for zone 92 to enable duress reporting)
95, 96, 99 =emergency zones
00 to continue
IMPORTANT: Do not include fire zones in zone lists that are used to STOP device actions.
01 Del Zn List?
0 = No 1 = Yes 0
0 = don’t delete list; current zone list remains saved
1 = delete this zone list; All zones in the zone list will be deleted automatically and the system returns to the
Zone List No. prompt.
[∗] to continue
01 Delete Zone?
0 = No 1 = Yes 0
0 = don’t delete zones; save zone list and return to the Zone List No. prompt.
1 = go to next prompt to delete zones
[∗] to continue
01 Zn to Delete?
(00 = Quit) 00
Enter each zone to be deleted from the list
01-64 = zones to be deleted from list followed by [∗] to accept each zone
00 when done to return to the Zone List No. prompt

–13 –
ALPHA VOCABULARY LIST (For Entering Zone Descriptors)
000
(Word Space)
–A –
•001 AIR
•002 ALARM
∗
004 ALLEY
005 AMBUSH
•006 AREA
•007 APARTMENT
•009 ATTIC
∗
010 AUDIO
–B –
•012 BABY
∗
•013 BACK
∗
•014 BAR
•016 BASEMENT
∗
•017 BATHROOM
∗
•018 BED
•019 BEDROOM
∗
020 BELL
•021 BLOWER
•022 BOILER
023 BOTTOM
025 BREAK
•026 BUILDING
–C –
028 CABINET
•029 CALL
030 CAMERA
031 CAR
033 CASH
034 CCTV
035 CEILING
036 CELLAR
•037 CENTRAL
038 CIRCUIT
•040 CLOSED
∗
•046 COMPUTER
047 CONTACT
–D –
•048 DAUGHTERS
049 DELAYED
•050 DEN
∗
051 DESK
•052 DETECTOR
∗
•053 DINING
∗
054 DISCRIMINATOR
055 DISPLAY
•057 DOOR
∗
•059 DOWN
•060 DOWNSTAIRS
061 DRAWER
•062 DRIVEWAY
•064 DUCT
–E –
•065 EAST
066 ELECTRIC
067 EMERGENCY ∗
068 ENTRY
•069 EQUIPMENT
•071 EXIT
∗
072 EXTERIOR
–F –
•073 FACTORY
075 FAMILY
•076 FATHERS
•077 FENCE
•079 FIRE
∗
•080 FLOOR
∗
081 FLOW
082 FOIL
•083 FOYER
084 FREEZER
•085 FRONT
∗
–G –
•089 GARAGE
∗
•090 GAS
091 GATE
•092 GLASS
093 GUEST
094 GUN
–H –
•095 HALL
∗
•096 HEAT
098 HOLDUP
099 HOUSE
100 INFRARED
•101 INSIDE
∗
102 INTERIOR
103 INTRUSION
–J –
104 JEWELRY
–K –
•105 KITCHEN
∗
–L –
•106 LAUNDRY
∗
•107 LEFT
108 LEVEL
•109 LIBRARY
∗
•110 LIGHT
111 LINE
•113 LIVING
∗
•114 LOADING
115 LOCK
116 LOOP
117 LOW
•118 LOWER
–M –
•119 MACHINE
121 MAIDS
122 MAIN ∗
•123 MASTER
∗
•125 MEDICAL
∗
126 MEDICINE
128 MONEY
129 MONITOR
•130 MOTHERS
•131 MOTION
∗
132 MOTOR
–N –
•134 NORTH
135 NURSERY
–O –
•136 OFFICE
∗
•138 OPEN
∗
139 OPENING
•140 OUTSIDE
142 OVERHEAD
–P –
143 PAINTING
•144 PANIC
∗
145 PASSIVE
•146 PATIO
∗
147 PERIMETER
•148 PHONE
150 POINT
151 POLICE ∗
152 POOL ∗
•153 POWER
–R –
155 RADIO
•156 REAR
157 RECREATION
159 REFRIGERATION
160 RF
•161 RIGHT
•162 ROOM
∗
163 ROOF
–S –
164 SAFE
165 SCREEN
166 SENSOR
•167 SERVICE
•168 SHED
∗
169 SHOCK
•170 SHOP
∗
171 SHORT
•173 SIDE
∗
174 SKYLIGHT
175 SLIDING ∗
•176 SMOKE
∗
•178 SONS
•179 SOUTH
180 SPRINKLER
•182 STATION
184 STORE
•185 STORAGE
∗
186 STORY
190 SUPERVISED ∗
191 SUPERVISION
192 SWIMMING
193 SWITCH
–T –
194 TAMPER
196 TELCO
197 TELEPHONE
•199 TEMPERATURE
200 THERMOSTAT
•201 TOOL
202 TRANSMITTER
–U –
•205 UP
•206 UPPER
•207 UPSTAIRS
∗
•208 UTILITY
∗
–V –
209 VALVE
210 VAULT
212 VOLTAGE
–W –
213 WALL
214 WAREHOUSE
•216 WEST
•217 WINDOW
∗
•219 WING
220 WIRELESS
–X –
222 XMITTER
–Y –
223 YARD
–Z –
224 ZONE (No.)
•225 ZONE
∗
•226 0
•227 1
•228 1ST
∗
•229 2
•230 2ND
∗
•231 3
•232 3RD
∗
•233 4
•234 4TH
•235 5
•236 5TH
•237 6
•238 6TH
•239 7
•240 7TH
•241 8
•242 8TH
•243 9
•244 9TH
245 Custom Word #1
246 Custom Word #2
247 Custom Word #3
248 Custom Word #4
249 Custom Word #5
250 Custom Word #6
251 Custom Word #7
252 Custom Word #8
253 Custom Word #9
254 Custom Word #10
Note: Bulleted (•) words in boldface type are those that are also available for use by the 4285/4286 Phone Module. If
using a Phone module, and words other than these are selected for Alpha descriptors, the module will not provide
annunciation of those words.
Italicized
words followed by an asterisk indicate those words supported by the 6160V/6150V Voice Keypads
CHARACTER (ASCII) CHART (For Adding Custom Words)
32 (space)
33 !
34 "
35 #
36 $
37 %
38 &
39 '
40 (
41 )
42 *
43 +
44 ,
45 –
46 .
47 /
48 0
49 1
50 2
51 3
52 4
53 5
54 6
55 7
56 8
57 9
58 :
59 ;
60 <
61 =
62 >
63 ?
64 @
65 A
66 B
67 C
68 D
69 E
70 F
71 G
72 H
73 I
74 J
75 K
76 L
77 M
78 N
79 O
80 P
81 Q
82 R
83 S
84 T
85 U
86 V
87 W
88 X
89 Y
90 Z

–14 –
Start Zone Descriptor Programming mode by pressing *82 while in Data Programming mode.
Program Alpha ?
0=No, 1=Yes 0
Press 1 to program descriptors.
0 = exit this mode
Custom Words ?
0=No, 1=Yes 00
To program standard alpha descriptors from the fixed vocabulary, press 0. The system will then
automatically display the descriptor for zone 1.
To define custom words (described below in “Adding Custom Words”section), pess 1.
✱ZN 01
Summary screen of zone 1 descriptor (if programmed) is displayed.
Press [∗] to start blinking cursor at zone number, then enter the zone number for which the descriptor is
being programmed.
•If a descriptor is programmed for that zone, it is displayed.
•To delete or change a previously programmed descriptor, press [∗] plus the same zone number. This will
clear that descriptor and move the cursor to the first word position.
•If you do not wish to change the existing descriptor, enter [∗] plus the next zone number for which you wish
to enter (or check) a descriptor. A summary display for that zone will appear. You must then press [∗] plus
the same zone number again to program a descriptor for that zone.
•If no descriptor has been programmed for that zone, the cursor moves to first word position.
✱ZN 01
Select first word of descriptor:
Press [#] plus the 3-digit index number for the first word from the Alpha Vocabulary List. See index for entries.
Example: The descriptor that we wish to enter for zone 1 is BACK DOOR. From the list, BACK = 013.
Therefore, you would enter #013.
NOTE: If you enter the wrong word, simply press [#] plus the correct 3-digit number for the word you want.
✱ZN 01 BACK
Save first word of descriptor:
6 = save word and go to next word in this descriptor
8 = save word and end descriptor if this is the only word used for the descriptor - go to summary screen
✱ZN 01 BACK
DOOR
Enter the 3-digit number for the next word. In the example, the word is DOOR, whose number is “057.”
See index for entries.
[∗] to continue
✱ZN 01 BACK
DOOR
Save second word of descriptor:
6 = save word and go to next word in this descriptor
8 = save word and end descriptor if this is the only word of the descriptor - go to summary screen
The two words in the example have now been entered. Note, however, that up to three words may be
entered (provided the number of characters will fit on the screen).
✱ZN 01 BACK
DOOR
Summary Screen
The blinking cursor will disappear, indicating that the word(s) are stored in memory for that zone.
To enter a descriptor for the next zone, press [∗] plus the desired zone number (e.g., ∗02).
The summary display for that zone will appear.
Repeat the previous steps to enter the descriptor for the next zone.
To exit the Alpha descriptor mode, enter zone “00”at the summary display, which returns you to the
Program Alpha prompt. Enter “0”at that prompt to exit.
Adding Custom Words (will not be annunciated by 4285/4286 Phone Module)
Program Alpha ?
0=No, 1=Yes 00
The “Program Alpha ?”prompt will appear.
1 = program zone descriptors and/or partition descriptors or reminder words; 0 = exit
[∗] to continue
Custom Words ?
0=No, 1=Yes 0
Custom words let you assign partition descriptors and “reminder”words (for Scheduling mode, event “10”).
NOTE: Do not assign reminder words if using fixed-word keypads.
1 = yes, program partition descriptors or reminder words; 0 = no, go to zone descriptors (see above)
If “1”selected, enter the 2-digit custom word number (01-10) to be programmed, corresponding to index
numbers 245 - 254 respectively (for example, if you are creating the first custom word or word-string, enter
01, for the second, enter 02, etc.). A cursor will now appear at the beginning of the second line.
Custom? 00 08-10 = “reminder”words used with scheduling mode
11 = partition 1 descriptor; 12 = partition 2 descriptor; 13 = common area
Custom? 01
Acursor appears at the beginning of the second line.
Special Keys: [6] = accept character and move cursor to next position to right
[4] = move cursor to left
[8] = save custom word
1. Refer to the Character Chart on the previous page.
Press [#], followed by the two-digit entry for the first letter you want to display (e.g., # 6 5 for “A”).
Press [6] to accept the character and move the cursor to the right, in position for the next character.
2. Repeat Step 1 to enter the next characters until the desired custom word is entered. You can use the
[4] key to move the cursor to the left, if necessary.
Each custom word can be a maximum of 10 characters.
3. When done, press the [8] key to save the custom word and return to the “Custom ?”prompt.
4. Repeat steps 1-3 to enter other custom words. To change a custom word, simply overwrite it.
To exit, enter “00,”which returns you to the Program Alpha prompt. Enter “0”at that prompt to exit.

–15 –
Schedules (installer code + [#] + [6] [4];
master code can only access schedules 01 and events 00-07
)
No. Event Device No. Group No. Start Time/ Stop Time/ Repeat Random
(see list below) for “01”events: for “02”events: Days Days (1-4) (yes/no)
enter 01-04 enter 1-8
01 (user)
02 (installer)
Events: Master/Installer Installer Only
00 = clear event 04 = forced STAY arm 10 = display custom words 8-10
01 = device on/off 05 = forced AWAY arm 11 = periodic test report
02 = user access 06 = auto disarm
03 = latch key report 07 = display “reminder”
Repeat Options: 0 = none; 1 = repeat weekly; 2 = repeat every other week; 3 = repeat every third week; 4 = repeat every fourth week
Start Scheduling mode by entering installer code + [#] + [6] [4] while in normal operating mode.
NOTE: The master code can only access schedules 01 and events 00-07.
ENTER SCHED NO.
00=QUIT 00
Enter the desired schedule number.
01 = end-user schedule; 02 = installer-only schedule; 00 = exit scheduling mode
[∗] to continue
ENTER EVENT
CLEAR EVENT 00
NOTE: Events 07 and 10
cause the keypad to
beep every 30 seconds
when messages are
displayed. Stop the
beeps by user code +
OFF.
Enter the desired event number for event you want to occur at a specified time.
Events 10-11 are reserved for the installer only.
00 = clear event
01 = Relay On/Off
02 = User Access
03 = Latch Key Report to Pager (sent to all pagers; message sent is 777-7777; user must be enabled for
paging)
04 = Forced Stay Arming (forced bypass is automatically enabled regardless of setting in field *23)
05 = Forced Away Arming (forced bypass is automatically enabled regardless of setting in field *23)
06 = Auto Disarm
07 = Display “Reminder”
10 = Display custom words (system displays custom words 8, 9, and 10 at defined time; can be used as
installer’s reminder message to the end user)
11 = Periodic Test Report
[∗] to continue
DEVICE NUMBER
XX
This prompt appears if event “1”(relay on/off) was selected, otherwise it is skipped.
Enter the physical device number as programmed in ∗79 Menu Mode.
01-04 = device number; 17, 18 = built-in triggers 1 and 2 respectively
[∗] to continue to the “Start”prompt
GROUP NUMBER
X
This prompt appears if event “2”(user access) was selected. Otherwise it is skipped.
1-8 = group number
[∗] to continue to the “Start”prompt
START SMTWTFS
HH MMAM 0010000
Enter the event’s start time and days of the week to occur.
01-12 = hour; 00-59 = minute; 0 = AM; 1 = PM
Days = position the cursor under the desired days using the [∗] key to move forward, then press “1”to select
the desired day(s)
[∗] to continue
START SMTWTFS
HH MMAM 0010000
Enter the event’s stop time and days of the week to occur.
This entry applies only to the following events: 1 (relay on/off); 2 (user access); 3 (latch key report)
01-12 = hour; 00-59 = minute; 0 = AM; 1 = PM
Days = position the cursor under the desired days using the [∗] key to move forward, then press “1”to select
the desired day(s)
[∗] to continue
REPEAT OPTION
0-4 X
Enter the desired repeat option for this schedule.
e.g., To make a schedule that happens everyday you would select all days with a repeat count of 1. To
make a schedule that runs for one week then stops, select everyday with a repeat count of 0.
0 = do not repeat; 1 = repeat schedule weekly; 2 = repeat schedule biweekly (every other week)
3 = repeat every 3rd week; 4 = repeat every 4th week
[∗] to continue
RANDOMIZE
0=NO 1=YES X
Select whether you want this schedule to start and stop at random times.
If selected, the scheduled start and stop times will vary within 60 minutes of the “hour”time. For example, if
a schedule is set to start at 6:15pm, it will do so the first time 6:15pm arrives, but on subsequent days it will
start anytime between 6:00 and 6:59 p.m.
[∗] to continue
NOTE: Do not use the random option if the start and stop times are within the same “hour”setting, otherwise
unpredictable results may occur (e.g., the randomized stop time may occur before the start time).

5800 Series Transmitter Input Loop Identification
5801
ENROLLAS "UR" OR "RF"
LOOP
1
5802MN
ENROLLAS "UR" OR "RF"
YOU MUST
ENROLL THIS
BUTTON
LOOP 3
LOOP 1
LOOP 2
LOOP 4
LOOP
1
5808
ENROLLAS "RF"
5804
ENROLL
AS "BR"
5817
ENROLLAS "RF"
LOOP
1
(PRIMARY)
2
(AUX. CENTER)
3
(AUX. RIGHT)
LOOP
1
(MOTION)
5890
ENROLLAS "RF"
5816
ENROLLAS "RF"
LOOP
2
(REED)
LOOP 1
(TERMINALS)
5827
SET HOUSE CODE 5827BD
SET HOUSE CODE
5816MN
ENROLLAS "RF"
LOOP
2
(REED)
LOOP 1
(TERMINALS)
5819
ENROLLAS "RF"
LOOP
2
(REED) LOOP 1
(TERMINALS)
ALTERNATE
POSITION
FOR LOOP2
LOOP 3
(TERMINALS) 5819S (WHS & BRS)
ENROLLAS "RF"
LOOP
2
(REED)
LOOP 1
(INTERNAL
SHOCK
SENSOR)
LOOP 3
(TERMINALS)
5850 (GBD)
ENROLLAS "RF"
(Green)
(Red)
(Yellow)
5804BD
ENROLLAS "BR"
•
•
•
••
••
•
•••
•
•
•
••
•
•
•
LOOP 3
LOOP 1
LOOP 2
LOOP 4
SET
HOUSE
CODE
YOU MUST
ENROLL THIS
BUTTON
LOOP 3
LOOP 1
LOOP 2
LOOP 4
YOU MUST
ENROLL THIS
BUTTON
LOOP
1
5809
ENROLLAS "RF"
LOOP 2
(REED)
Transmitters illustrated have one or more unique factory
assigned input (loop) ID codes. Each of the inputs
requires its own programming zone (e.g., a 5804's four
inputs require four zones).
For information on any transmitter not shown above,
refer to the instructions accompanying that transmitter
for details regarding loop numbers, etc.
UL NOTE: The following transmitters are not
intended for use in UL installations: 5802MN,
5802MN2, 5804, 5804BD, 5814, 5816TEMP, 5819,
5819WHS & BRS, and 5850.
The 5827BD and 5800TM can be used in UL Listed
Residential Burglar installation
A DIVISION OF PITTWAY CORPORATION
165 Eileen Way, Syosset, NY 11791
Copyright © 2002 Pittway Corporation
¬.359l
K0735PRV1 9/02