ADLINK Technology cPCIS-3330 Series User manual

Advance Technologies; Automate the World.
Manual Rev. 2.00
Revision Date: May 30, 2005
Part No: 50-15017-100
cPCIS-3330 Series
8-Slot for 6U
CompactPCI Platform
User’s Manual

Copyright 2005 ADLINK TECHNOLOGY INC.
All Rights Reserved.
The information in this document is subject to change without prior
notice in order to improve reliability, design, and function and does
not represent a commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, spe-
cial, incidental, or consequential damages arising out of the use or
inability to use the product or documentation, even if advised of
the possibility of such damages.
This document contains proprietary information protected by copy-
right. All rights are reserved. No part of this manual may be repro-
duced by any mechanical, electronic, or other means in any form
without prior written permission of the manufacturer.
Trademarks
Product names mentioned herein are used for identification pur-
poses only and may be trademarks and/or registered trademarks
of their respective companies.

Getting Service from ADLINK
Customer Satisfaction is top priority for ADLINK Technology Inc.
Please contact us should you require any service or assistance.
ADLINK TECHNOLOGY INC.
Web Site: http://www.adlinktech.com
Sales & Service: [email protected]
TEL: [phone]
FAX: [phone]
Address: 9F, No. 166, Jian Yi Road, Chungho City,
Taipei, 235 Taiwan
Please email or FAX this completed service form for prompt and
satisfactory service.
Company Information
Company/Organization
Contact Person
E-mail Address
Address
Country
TEL FAX:
Web Site
Product Information
Product Model
Environment
OS:
M/B: CPU:
Chipset: Bios:
Please give a detailed description of the problem(s):

Table of Contents i
Table of Contents
List of Figures ........................................................................ iii
1 Introduction ........................................................................ 1
1.1 Features............................................................................... 1
1.2 cPCIS-3330 Configurations ................................................. 2
1.3 Specifications....................................................................... 3
1.4 Mechanical Layout............................................................... 4
cPCIS-3330 Series Mechanical Layout .......................... 4
cPCIS-3330 Series External Dimensions (mm) .............. 5
2 Getting Started ................................................................... 7
2.1 Shipping Contents ............................................................... 7
2.2 CompactPCI Computing Blade & PSU Installation.............. 7
CompactPCI Card Installation/Removal Procedure ........ 8
CompactPCI PSU Installation/Removal Procedure ...... 10
2.3 Rear Transition Module Installation/Removal .................... 11
2.4 Drive Bay Access............................................................... 12
2.5 Powering Up the System ................................................... 13
2.6 System Alarm Board.......................................................... 14
3 Backplanes ....................................................................... 15
3.1 cBP-6108R (32-bit/33MHz)................................................ 16
Features ....................................................................... 16
Specifications ................................................................ 16
Mechanical Drawing ..................................................... 17
Connector Pin Assignments ......................................... 19
Jumper Settings ............................................................ 34
3.2 cBP-6408R (64-bit/66MHz)................................................ 35
Features ....................................................................... 35
Specifications ................................................................ 35
Mechanical Drawing ..................................................... 36
Connector Pin Assignments ......................................... 38
Jumper Settings ............................................................ 50
3.3 cBP-3064 CompactPCI Power Backplane......................... 51
Specifications ................................................................ 51
Mechanical Drawing ..................................................... 52
Connector Pin Assignments ......................................... 54

ii Table of Contents
4 Cooling System................................................................. 59
4.1 Fan Alarm .......................................................................... 59
4.2 Fan Removal and Replacement ........................................ 59
Intake Fans ................................................................... 60
Front Exhaust Fans ...................................................... 61
Rear Exhaust Fans ....................................................... 62
4.3 Fan Tray Filter Replacement ............................................. 62
5 Power Supply Unit ............................................................ 63
5.1 Features............................................................................. 63
5.2 Specifications..................................................................... 63
5.3 Input Characteristics .......................................................... 64
5.4 Output Characteristics ....................................................... 65
Important Safety Instructions............................................... 67
Warranty Policy ..................................................................... 69

List of Figures iii
List of Figures
Figure 1-1: Mechanical Layout of the cPCIS-3330 ...................... 4
Figure 1-2: cPCIS-3330 Series Front View.................................. 5
Figure 1-3: cPCIS-3330 Series Side View ................................... 5
Figure 2-1: cPCIS-3330 Series slot layout................................... 8
Figure 2-2: Installing 6U Processor Blade. .................................. 9
Figure 2-3: Latching the cPCI module handles securely. .......... 10
Figure 2-4: Unlatching and removing a cPCI PSU..................... 11
Figure 2-5: Remove drive bay bracket fastening screws. .......... 12
Figure 2-6: Remove rear panel fastening screws;
CD-ROM drive bay blanking cover screw locations 13
Figure 2-7: cPCIS-3330 switch and LED legend. ...................... 14
Figure 3-1: cBP-6108R Backplane Front View .......................... 17
Figure 3-2: cBP-6108R Backplane Rear View........................... 18
Figure 3-3: cBP-6408R Backplane Front View .......................... 36
Figure 3-4: cBP-6408R Backplane Rear View........................... 37
Figure 3-5: cBP-3064 Power Backplane Front View.................. 52
Figure 3-6: cBP-3064 Power Backplane Rear View .................. 53
Figure 4-1: Front fan tray cover locations .................................. 59
Figure 4-2: Remove the intake fan tray cover............................ 60
Figure 4-3: Remove the screws securing the fan module.......... 60
Figure 4-4: Remove the faulty intake fan module ...................... 61
Figure 4-5: Remove the screws securing the fan module.......... 61
Figure 4-6: Loosen the screws securing the rear fan module.... 62

Introduction 1
1 Introduction
The cPCIS-3330 Series is a 19” 8-slot 6U CompactPCI Sub-
system ideally suited to Network Equipment Providers, Computing
Telephony Integrators and Voice over IP applications. This flexible
and reliable development platform with optimized I/O and storage
provides the best solution for equipment manufacturers and sys-
tem integrators and shortens time-to-market for fast growing busi-
ness revenues.
The cPCIS-3330 provides scalability up to 7 peripheral slots with
either 32-bit/33MHz or 64-bit/33MHz PCI and H.110 CT busses,
redundant cooling system (5+5 front access hot swappable fans),
750W + 250W redundant PICMG 2.11 cPCI power supply, two
5.25”, one 3.5” drive bays, and one slim type CD-ROM drive.
1.1 Features
XStandard 6U CompactPCI and PICMG 2.5 compliant H.110
CT Bus
XOne cPCI segment, right-hand-side system slot
X1 system slot, 7 peripheral slots
XPICMG 2.1 Hot Swap compliant 32-bit or 64-bit 8-slot Com-
pactPCI backplane with P3 & P5 rear I/O
XTwo 5.25”, one 3.5”, and one slim type CD-ROM drive bays
X3+1 (750W + 250W) hot swappable redundant cPCI power
suppies with Universal AC input
X5+5 front access, push-pull, hot swappable fan redundant
cooling architecture; removable air filter; two rear access
fans
XAlarm module monitors temperature and fan status
XGuarded power switch and alarm reset button
XDesigned for NEBS Level 3 compliance

2Introduction
1.2 cPCIS-3330 Configurations
The cPCIS-3330 Series comes in the configurations shown in the
table below. .
Model Number Description
cPCIS-3330/AC 8-slot 6U 32-bit CompactPCI Chassis with 4
cPS-325/AC Redundant Power Supplies
cPCIS-3330/64/AC 8-slot 6U 64-bit CompactPCI Chassis with 4
cPS-325/AC Redundant Power Supplies
cPCIS-3330/DC4 8-slot 6U 32-bit CompactPCI Chassis with 4
cPS-325/48 Redundant Power Supplies

Introduction 3
1.3 Specifications
CompactPCI Standards PICMG 2.0; 2.1; 2.5; 2.9; 2.11
Form Factor 6U cPCI with 80 mm depth rear I/O
Enclosure
EIA RS-310C 19" 9U high rack-mount enclosure
Coated metal plate outer covering
Guarded power switch and reset button
Backplane
32-bit/33MHz PCI or 64-bit/33MHz PCI
(model dependent)
H.110 CT Bus
1 system slot, 7 peripheral slots
P3, P4 and P5 rear I/O with AB-type shroud
(see Chapter 3 for detailed specifications)
Power Supply
Supports up to 4 in-rack 3U cPCI 8HP power modules
Supports current sharing on 5V, 3.3V and 12V
PICMG 2.11 47-pin power interface
Available power module: cPS-H325/AC or cPS-H325/48
(250W N+1 redundant each)
Cooling System
Front access hot swappable fan trays for intake and
exhaust with removable air filter:
12V DC brushless, dual ball bearing
5 fans for intake and 5 fans for exhaust
Rated power for each fan: 2.64W
Air flow: 241 CFM
Two rear access fans for exhaust (51CFM, 2.9W each)
Alarm Module
Monitors inner chassis temperature & fan status (model
dependent)
Abnormal status will generate alarm and LED warning
Audible alarm reset
LED indicators display voltage status on 5V, 3.3V, 12V, -12V
Drive Bays Two 5.25” one 3.5” and one slim type CD-ROM drive bays
Dimension 483.2 x 399 x 299.1 (mm, WxHxD, w/o handles)
Operating temperature 0 to 55°C (depending on system configuration)
Storage temperature -20 to 80°C
Humidity 5% to 95%, non-condensing
Shock 15G peak-to-peak, 11ms duration, non-operation
Vibration
Non-operation: 1.88Grms, 5-500Hz, each axis
Operation: 0.5Grms, 5-500Hz, each axis (tested with 2.5"
HDD)
Safety, Certification, EBS CE, FCC class A, designed for NEBS Level 3

4Introduction
1.4 Mechanical Layout
Refer to the figures below for the mechanical layout and external
dimensions of the cPCIS-3330.
cPCIS-3330 Series Mechanical Layout
Figure 1-1: Mechanical Layout of the cPCIS-3330

Introduction 5
cPCIS-3330 Series External Dimensions (mm)
Figure 1-2: cPCIS-3330 Series Front View
Figure 1-3: cPCIS-3330 Series Side View

6Introduction

Getting Started 7
2 Getting Started
This chapter describes the unpacking procedure of the sub-sys-
tem and installation procedures for CompactPCI boards, power
supply units (PSUs) and drive bays.
2.1 Shipping Contents
Check the shipping carton for any damage. If the shipping carton
and contents are damaged, please notify the dealer for a replace-
ment. Retain the shipping carton and packing material for inspec-
tion by the dealer. Obtain authorization before returning any
product to ADLINK.
Check that the following items are included in the package. If there
are any missing items, please contact your dealer:
XOne cPCIS-3330 Series Subsystem
XThis User’s Manual
XAccessory Kit (includes N. American or European power
cord, air filter and spare screws)
2.2 CompactPCI Card & PSU Installation
The CompactPCI connectors are rigid and require careful handling
when inserted and removed. Improper handling of cards can eas-
ily damage the backplane.
The system slot is red, peripheral slots are gray, and PSU slots are
green. Be certain to insert each module into the correct type of
slot.
System slots have obvious indicators (e.g. red card guide rail, tri-
angle mark enclosing the slot number on the backplane) A system
board can only be installed in a system slot. Do not insert a system
board into any other slot, or insert any peripheral card into a sys-
tem slot.

8 Getting Started
Figure 2-1: cPCIS-3330 Series slot layout
The handles on CompactPCI cards and PSUs ensure simple and
safe installation and removal. Please follow the procedures below
to install a CompactPCI module into a chassis:
CompactPCI Card Installation/Removal Procedure
1. Place the sub-system on a level surface or rackmount it.
Remove the blanking plates where required by undoing
the retaining screws at each end. Retain the blanking
plates for possible future use. The system should not be
put into use without blanking plates covering all empty
slots, otherwise the EMC and cooling performance will
be compromised
2. Hold the system board or peripheral card module verti-
cally. Make sure that the handles are unlatched (i.e. that

Getting Started 9
they are pulled outwards) by first pressing on the release
buttons with your thumb.
3. Carefully insert the module into the desired slot by slid-
ing the edges of the board into the appropriate card
guide rail. Take care to ensure correct alignment of the
card with the chassis during insertion to prevent damage
to the card and/or backplane.
Figure 2-2: Installing 6U CompactPCI card
4. Continue inserting the card until the handles engage with
the chassis.
5. Push inwards on the handles for final insertion. Ensure
that the buttons on the handles fully latch into position as
unless this is done the card is not correctly inserted. Fas-
ten the retaining screws at each end of the card (2 for
single slot cards, 4 for double slot cards).

10 Getting Started
Figure 2-3: Latching the cPCI module handles securely
6. To remove the module, undo the retaining screws, press
the release buttons (if necessary), and reverse steps 1
through 5 above.
CompactPCI PSU Installation/Removal Procedure
The cPCIS-3330 Series come with cPS-H325 PSUs pre-installed.
The removal and installation procedures for PSUs are the same
as for CompactPCI cards, except there is only one handle. To
replace a PSU module, refer to the figures and instructions below.
1. To remove the PSU module, undo the retaining screws
and unlatch the handle by pressing on the release but-
ton.

Getting Started 11
Figure 2-4: Unlatching and removing a cPCI PSU
2. Pull outwards to remove the PSU.
3. Insert the new PSU module, push on the handle until it
latches into position, and replace the retaining screws.
2.3 Rear Transition Module Installation/Removal
The installation and removal procedures for a Rear Transition
Module (RTM) are the same as those for CompactPCI boards.
Because they are shorter than front boards, pay careful attention
when inserting or removing RTMs. Only models with an “R” at the
end of the model number support RTMs.
Note: We strongly recommended the use of RTMs with AB type
connectors to prevent the damage to the backplane during
RTM installation.

12 Getting Started
2.4 Drive Bay Access
To install the required hardware in the two 5.25”, one 3.5”, and
one slim type CD-ROM drive bays, follow the procedure below:
1. Loosen the 8 screws securing the drive bay bracket to
the cPCIS-3330 chassis as shown in the figure below.
Figure 2-5: Remove drive bay bracket fastening screws
2. Loosen the 8 screws fastening the PSU rear panel to the
chassis as shown in the figure below. Remove the rear
panel, reach inside the chassis, and push the drive bay
bracket forwards out of the chassis.
3. Undo the screws attaching the drive bay blanking covers
to the drive bay bracket as required. Note the locations
of the CD-ROM drive bay blanking cover screws in the
figure below.