ADTRAN SFP User manual

Q
uic
k
Start
DESCRIPTION
This guide supports the following products:
The Small Form-Factor Pluggable (SFP) 2.67Gbps Bidirectional
(BIDI) 80 km plugs into ADTRAN equipment designed to accept
SFPs. Installed into an appropriate host unit, the Bidirectional
single fiber BIDI SFP provides up to 2.67Gbps optical interface to
the supporting system.
gNOTE
The 1442825F1 and 1442825F2 must be deployed as pairs at
each end of the system. The 1442825F1 must be connected to
the 1442825F2 at the other end of the fiber.
INSTALLATION
To install the SFP into an appropriate module, complete the
following steps:
1. Inspect the SFP. If damaged, file a claim with the carrier and
then contact ADTRAN Customer Service.
2. Do not remove the protective end cap from the SFP until the
fiber optic cable is ready to be connected.
3. Insert the SFP into the SFP cage on the module. Ensure the
manufacturer’s label on the SFP is facing upward for correct
installation.
4. Slide the SFP all the way into the receptacle until there is an
audible “click.”
wNOTICE
The latch on the SFP is used to remove the SFP from the cage on
the circuit card
f
CAUTION!
Due to compliance certification requirements, use only SFPs
supplied by ADTRAN. ADTRAN cannot certify system integrity
with other SFPs.
Part Number Description
1442825F1 SFP 2.67Gbps BIDI 1590/1490 nm
1442825F2 SFP 2.67Gbps BIDI 1490/1590 nm
OPERATIONAL SPECIFICATIONS
General
■Module type: SFP
■Fiber/Copper: Fiber
♦SM/MM: Single Mode
♦Single/Dual-fiber: Single Fiber
■Optical Connector: LC
■Applications: OC-48/STM-16; 1.0 G; 2.5 G
■Distance: 80 km
■Digital Diagnostic Monitoring: SFF- 8472 and SFF-8047i
Compliant
Optical
■Optical Budget: 26 dB
■Transmitter
♦Tx Central Wavelength
●11442825F1: 1590 nm
●11442825F2: 1490 nm
♦Tx Output Optical Power: –2.0 dBm to +3.0 dBm
♦Tx Spectral Width: 1 nm
♦SMSR: 30 dB
♦Extinction Ratio: 8.2 dB
♦Dispersion Penalty: 2 dB
■Receiver
♦Rx Central Wavelength
●11442825F1: 1490 nm
●11442825F2: 1590 nm
♦Input optical power: –7.0 dBm to –28.0 dBm
♦Receiver Overload: –7.0 dBm
♦Receiver Sensitivity: –28.0 dBm
Environmental
■Protected Equipment Environment (Outside)
●Case temperature hardened range: –40°C to +85°C
♦Operational temperature range: –40°C to +65°C
♦Storage temperature range: –40°C to +85°C
♦Relative humidity to 5 to 85%
ADTRAN Pluggable Optics
SFP
2.67Gbps BIDI 80 km
December 2018
61442825F1-13B

2 61442825F1-13B
gNOTE
■The Gigabit Ethernet port(s) are optical and therefore are not
classified as any type of port as defined in Appendix B of GR-
1089-CORE.
■This product is designed to be deployed in GR-3108-CORE
environmental class 2 as defined in GR-3108-CORE.
■This product is NRTL Listed to the applicable UL Standards.
The product is designed to meet the applicable requirements
of Telcordia GR-63-CORE and GR-1089-CORE.
■This product has also been evaluated to international safety
standards EN 60950-1, AS/NZS 60950.1, and IEC 60950-1.
This product meets the requirements for CE marking under the
EMC Directive and Low Voltage Directive. Standards used to
demonstrate Compliance are EN 300 386 and EN 60950.
■This device complies with Part 15 of the FCC rules. Operation
is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
■Changes or modifications not expressly approved by ADTRAN
could void the user's authority to operate this equipment.
■This product is designed to meet the following environmental
classes:
♦ETSI EN 300 019-2-1 “Classification of environmental condi-
tions; Storage Class” 2.1
♦ETSI EN 300 019-2-2 “Classification of environmental condi-
tions, Transportation”, Class 2.2
♦ETSI EN 300 019-2-3 “Classification of environmental condi-
tions, Stationary use at weather protected locations”, Class
3.1E
■This product is designed to function without degradation during
exposure to all test severities per Class 3.3 of ETSI EN 300
019-1-3.
■This product meets EU RoHS Directive. Refer to
www.adtran.com for further information on RoHS/WEEE.
■To ensure compatibility, refer to the ADTRAN Pluggable
Optics Compatibility Matrix (online tool, go to: http://
www.adtran.com/pluggableoptics).
SAFETY AND REGULATORY
ENGLISH
fWARNING!
Read all warnings and cautions before installing or servicing this
equipment.
CCAUTION!
This product is a Class 1 Laser module that complies with FDA 21
CFR 1040.10 and 1040.11 and IEC 60825-1. This product is
NRTL Listed and CB Certified to all applicable American and
European safety standards. For continued compliance with the
above standards, install only ADTRAN-approved Class 1 Laser
Modules in ADTRAN products. For a list of ADTRAN-approved
SFPs and XFPs, see http:/www.adtran.com/pluggableoptics.
ADTRAN cannot certify system integrity with other laser modules.
f
CAUTION!
■Electrostatic Discharge (ESD) can damage electronic
modules. When handling modules, wear an antistatic
discharge wrist strap to prevent damage to electronic
components. Place modules in antistatic packing material
when transporting or storing. When working on modules,
always place them on an approved antistatic mat that is
electrically grounded.
■The SFP meets or exceeds all the applicable requirements of
NEBS, Telcordia GR-63-CORE, and GR-1089-CORE. The
product is intended for deployment in Central Office type
facilities, EEEs, EECs, and locations where the NEC applies
(for example, Customer Premises.)
■Per GR-1089-CORE the ADTRAN system that the SFP is
being deployed in is designed and intended for installation as
part of a Common Bonding Network (CBN). The ADTRAN
system that the SFP is being deployed in is not designed nor
intended for installation as part of an Isolated Bonding Network
(IBN).
■This product does not have an internal DC connection
between battery return and frame ground. This product can be
installed in a DC-I (isolated) or DC-C (common) configuration.
■The chassis frame ground terminal must be connected to an
earth ground to ensure that the exposed metal (for example,
front panels, SFP/XFP modules) on the product is properly
grounded by way of the backplane connector.

61442825F1-13B 3
FRANÇAIS
fAVERTISSMENT!
Lisez tous les avertissements et mises en garde avant l’instal-
lation de cet équipement ou la réalisation de toute opération de
maintenance.
C
ATTENTION!
Ce produit est un module laser de classe 1 qui est conforme à la
FDA 21 CFR 1040.10 et 1040.11 et IEC 60825-1. Ce produit est
NRTL et Certifié CB à toutes les normes de sécurité applicables
américains et européens. Pour maintenir la conformité avec les
normes ci-dessus, installer des modules laser de classe 1 ne
ADTRAN approuvés dans les produits d'ADTRAN. Pour une liste
des SFP et XFP ADTRAN approuvés, voir http:/www.adtran.com/
pluggableoptics.ADTRAN ne peut certifier l'intégrité du système
avec d'autres modules laser.
fATTENTION!
■L'ESD (décharge électrostatique) peut endommager les
modules électroniques. Lors de la manipulation des modules,
portez un bracelet de décharge antistatique pour éviter
d'endommager les composants électroniques. Placez les
modules dans un emballage antistatique lors du transport ou
du stockage. Lorsque vous travaillez sur les modules, placez-
les toujours sur un tapis antistatique certifié muni d'un
branchement de mise à la terre.
■Ce système est conçu et prévu pour une installation intégrée
à un réseau de masse maillé. Ce système n’est pas conçu ni
prévu pour une installation intégrée à un réseau de masse
isolé (IBN).
■Ce produit ne dispose pas d’une connexion c.c. interne entre
le courant de retour de la batterie et la masse du châssis. Ce
produit peut être installé en configuration c.c.-I (isolé) ou c.c.-
C (commun).
■La borne de terre de châssis doit être connecté à une prise de
terre pour assurer que le métal exposé (tels que les panneaux
avant, des modules SFP / XFP) sur le produit est correctement
mis à la terre via le connecteur de fond de panier.
gREMARQUE
Ce produit est conforme à la directive européenne RoHS.
Reportez-vous à www.adtran.com pour de plus amples rensei-
gnements sur RoHS.
DEUTSCH
f
WARNUNG!
Lesen Sie sich alle Warn- und Sicherheitshinweise durch, bevor
Sie dieses Gerät installieren oder warten.
C
VORSICHT!
Dieses Produkt ist ein Klasse 1 Laser -Modul, das mit der FDA 21
CFR 1040.10 und 1040.11 und IEC 60825-1 entspricht. Dieses
Produkt wurde NRTL gelistet und CB Certified allen geltenden
amerikanischen und europäischen Sicherheitsstandards. Für die
ständige Einhaltung der oben genannten Normen, installieren Sie
nur ADTRAN zugelassene Klasse 1 Lasermodule in ADTRAN
Produkte. Eine Liste der ADTRAN zugelassene SFPs und XFPs
finden Sie unter http:/www.adtran.com/pluggableoptics. ADTRAN
kann nicht die Unversehrtheit des Netzes mit anderen Laser-
Module zertifizieren.
f
VORSICHT!
■Elektrostatische Entladung (ESD) können elektronische
Baugruppen beschädigt werden. Beim Umgang mit Modulen ,
tragen Sie eine Antistatikarmband, um Schäden an
elektronischen Bauteilen zu verhindern. Ort -Module in
antistatische Verpackung, beim Transport oder Lagerung. Bei
Arbeiten an Modulen immer legen Sie sie auf einer
zugelassenen antistatische Unterlage, die elektrisch geerdet
ist.
■Das System wurde für den Einsatz als Teil eines
gemeinsamen Potentialausgleichssystems (Common
Bonding Network) entwickelt. Das System ist nicht für den
Einsatz als Teil eines getrennten Potentialausgleichssystems
(Isolated Bonding Network) vorgesehen.
■Dieses Produkt hat keinen internen Gleichstromanschluss
zwischen Batterierücknahme und Gehäusemasse. Dieses
Produkt kann in einer DC-I (isoliert) oder DC-C (emeinsam).
■Der Fahrgestellrahmen Erdanschluß muß zu einer Erde
verbunden werden, um sicherzustellen, dass das freiliegende
Metall (dh Frontplatten, SFP / XFP-Module) auf dem Produkt
richtig über den Backplane-Anschluss geerdet ist.
g
HINWEIS
Dieses Produkt erfüllt die EU RoHS Richtlinie. Bitte besuchen Sie
www.adtran.com für ausführlichere Informationen zu RoHS/
WEEE.

CAUTION!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY
HANDLING PRECAUTIONS REQUIRED
Warranty: ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can be
found online at www.adtran.com/warranty.
Trademarks: Brand names and product names included in this document are trademarks,
registered trademarks, or trade names of their respective holders.
©2018 ADTRAN, Inc. All Rights Reserved.
ADTRAN CUSTOMER CARE:
From within the U.S. 1.888.423.8726
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61442825F1-13B*
Documentation for ADTRAN Network Solutions products is available for
viewing and download directly from the ADTRAN Support Community
website.
Go to: https://supportforums.adtran.com/welcome
Registration is required.
ADTRAN offers training courses on our products, including customized
training and courses taught at our facilities or at customer sites.
For inquiries, go to: http://adtran.com/training
The following online documents and resources provide additional information for this product:
ADTRAN Pluggable Optics Compatibility Matrix (online tool, go to: https://adtran.com/
pluggableoptics)