ADTRAN NetVanta 6355 PoE User manual

NetVanta 6355 PoE
Hardware Installation Guide
1200740E1 NetVanta 6355 PoE
1200690E1 NetVanta Quad FXS Voice Interface Module
1202691G1 NetVanta Quad FXO Voice Interface Module
1202692E1 NetVanta Dual FXS/FXO Voice Interface Module
1200695L1 NetVanta T1/PRI Voice Interface Module
1200696G1 NetVanta E1/PRI Voice Interface Module
1202862L1 NetVanta T1/FT1 Network Interface Module
1202863L1 NetVanta T1/FT1 + DSX-1 Network Interface Module
1202872L1 NetVanta Dual T1 Network Interface Module
1202869E1 NetVanta ADSL Network Interface Module, Annex A
1200868E1 NetVanta E1/FE1 Network Interface Module
1200878E1 NetVanta E1/FE1 + G.703 Network Interface Module
1702803F1 NetVanta USB WWAN Network Interface Module
1200852G1 CompactFlash®, 1 GB
4200368L1 Enhanced Feature Pack (Hardware and Software) for IPsec VPN Upgrade
61200740E1-34F
July 2013

Trademarks NetVanta 6355 PoE Hardware Installation Guide
2 Copyright © 2013 ADTRAN, Inc. 61200740E1-34F
Trademarks
Any brand names and product names included in this manual are trademarks, registered trademarks, or
trade names of their respective holders.
To the Holder of the Manual
The contents of this manual are current as of the date of publication. ADTRAN reserves the right to change
the contents without prior notice.
In no event will ADTRAN be liable for any special, incidental, or consequential damages or for
commercial losses even if ADTRAN has been advised thereof as a result of issue of this publication.
Software Licensing Agreement
Each ADTRAN product contains a single license for ADTRAN-supplied software. Pursuant to the
Licensing Agreement, you may: (a) use the software on the purchased ADTRAN device only and (b) keep
a copy of the software for backup purposes. This Agreement covers all software installed on the system, as
well as any software available on the ADTRAN website. In addition, certain ADTRAN systems may
contain additional conditions for obtaining software upgrades.
901 Explorer Boulevard
P.O. Box 140000
Huntsville, AL 35814-4000
Phone: [phone]
Copyright © 2013 ADTRAN, Inc.
All Rights Reserved.
Printed in U.S.A.
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.

NetVanta 6355 PoE Hardware Installation Guide Conventions
61200740E1-34F Copyright © 2013 ADTRAN, Inc. 3
Conventions
Notes provide additional useful information.
Cautions signify information that could prevent service interruption or damage to the
equipment.
Warnings provide information that could prevent injury or endangerment to human
life.

Safety Instructions NetVanta 6355 PoE Hardware Installation Guide
4 Copyright © 2013 ADTRAN, Inc. 61200740E1-34F
Safety Instructions
When using your telephone equipment, please follow these basic safety precautions to reduce the risk of
fire, electrical shock, or personal injury:
1. Do not use this product near water, such as a bathtub, wash bowl, kitchen sink, laundry tub, in a
wet basement, or near a swimming pool.
2. Avoid using a telephone (other than a cordless type) during an electrical storm. There is a remote
risk of shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord, power supply, and batteries indicated in the manual. Do not dispose of
batteries in a fire. They may explode. Check with local codes for special disposal instructions.
5. The socket outlet shall be installed near the equipment and shall be easily accessible.
If any of the following conditions occur, unplug the product from the electrical outlet and replace the part
or contact your qualified service personnel:
1. The power cable, extension cable, or plug is damaged.
2. An object has fallen into the product.
3. The product has been exposed to water.
4. The product has been dropped or damaged.
5. The product does not operate correctly when you follow the operating instructions.
Save These Important Safety Instructions
This equipment incorporates double pole/neutral fusing. If the neutral fuse opens and the
line fuse does not open, voltage could still be present in the unit.
These units contain no user-serviceable parts. They should only be serviced by qualified
service personnel.
Additional safety guidelines, such as Waste Electrical and Electronic Equipment (WEEE),
are given in the document NetVanta Safety and Regulatory Information available online at
http://supportforums.adtran.com.

NetVanta 6355 PoE Hardware Installation Guide FCC-Required Information
61200740E1-34F Copyright © 2013 ADTRAN, Inc. 5
FCC-Required Information
FCC regulations require that the following information be provided in this manual:
1. This equipment complies with Part 68 of Federal Communications Commission (FCC) rules and
requirements adopted by America’s Carriers Telecommunications Association (ACTA). Each
registered interface has a label that contains, among other information, a product identifier in the
format US:AAAEQ##TXXXX. If requested, provide this information to the telephone company.
2. If this equipment causes harm to the telephone network, the telephone company may temporarily
discontinue service. If possible, advance notification is given; otherwise, notification is given as
soon as possible. The telephone company will advise the customer of the right to file a complaint
with the FCC.
3. The telephone company may make changes in its facilities, equipment, operations, or procedures
that could affect the proper operation of this equipment. Advance notification and the opportunity
to maintain uninterrupted service are given.
4. If experiencing difficulty with this equipment, please contact ADTRAN for repair and warranty
information. The telephone company may require this equipment to be disconnected from the
network until the problem is corrected, or it is certain the equipment is not malfunctioning.
5. This unit contains no user-serviceable parts.
6. This equipment is designed to connect to the telephone network or premises wiring using an
FCC-compatible modular jack, which is compliant with Part 68 and requirements adopted by
ACTA.
7. The following information may be required when applying to the local telephone company for
leased line facilities:
8. The ringer equivalency number (REN) is useful in determining the quantity of devices you may
connect to your telephone line and still have all of those devices ring when your number is called.
In most areas, the sum of the RENs of all devices should not exceed five. To be certain of the
number of devices you may connect to your line as determined by the REN, call your telephone
company to determine the maximum REN for your calling area.
9. This equipment may not be used on coin service provided by the telephone company. Connection
to party lines is subject to state tariffs. Contact your state public utility commission or corporation
commission for information.
Part Number Registration Number Service Type REN/SOC FIC USOC
1202862L1 US: HDCDENAN1202863L1 1.544 Mbps - SF
1.544 Mbps - SF and B8ZS
1.544 Mbps - ESF
1.544 Mbps - ESF and B8ZS
6.0N
04DU9-BN
04DU9-DN
04DU9-1KN
04DU9-1SN
RJ-48C
1202863L1
1202872L1 US: HDCDENAN1200872L1
1200695L1 US: HDCDENAN1200695L1
1202869E1 US: HDCDL01A1200869L1 ADSL, ADSL2, ADSL2+ 0.1A Metallic RJ-11C
1200691E1 US: HDCMM01B1200691L1 Analog Loop Start/Ground Start 0.1B 02LS2/02GS2 RJ-11C1202692E1
1200740E1 US: HDCIS01B1200740L1

FCC Radio Frequency Interference Statement NetVanta 6355 PoE Hardware Installation Guide
6 Copyright © 2013 ADTRAN, Inc. 61200740E1-34F
FCC Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio frequencies. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Electromagnetic Compatibility (EMC) Table
NetVanta Module P/N and Name NetVanta 6355 PoE
1200690E1 Quad FXS VIM FCC Part 15 Class A
EN 55022 Class A
EN 55024
1202691G1 Quad FXO VIM FCC Part 15 Class A
EN 55022 Class A
EN 55024
1202692G1 Dual FXS/FXO VIM FCC Part 15 Class A
EN 55022 Class A
EN 55024
1200695L1 T1/PRI VIM FCC Part 15 Class A
EN 55022 Class A
EN 55024
1200696G1 E1/PRI VIM FCC Part 15 Class A
EN 55022 Class A
EN 55024
1202862L1 T1/FT1 NIM FCC Part 15 Class A
EN 55022 Class A
1202863L1 T1/FT1 + DSX-1 NIM FCC Part 15 Class A
EN 55022 Class A
1202872L1 Dual T1 NIM FCC Part 15 Class A
EN 55022 Class A
1202869E1 ADSL NIM, Annex A FCC Part 15 Class A
EN 55022 Class A
1200868E1 E1/FE1 NIM FCC Part 15 Class B
EN 55022 Class B
EN 55024
1200878E1 E1/FE1 + G.703 NIM FCC Part 15 Class B
EN 55022 Class B
EN 55024
1702803F1 USB WWAN NIM FCC Part 15 Class A
EN 55022 Class B
EN 55024
1202368L1 VPN Accelerator Card
(included in P/N 4200368L1) FCC Part 15 Class A EN 55022 Class A
EN 55024
EN 61000-3-2
EN 61000-3-3

NetVanta 6355 PoE Hardware Installation Guide Industry Canada Compliance Information
61200740E1-34F Copyright © 2013 ADTRAN, Inc. 7
Industry Canada Compliance Information
Notice: The Industry Canada label applied to the product (identified by the Industry Canada logo or the
“IC:” in front of the certification/registration number) signifies that the Industry Canada technical
specifications were met.
Notice: The REN for this terminal equipment is supplied in the documentation or on the product labeling/
markings. The REN assigned to each terminal device indicates the maximum number of terminals that can
be connected to a telephone interface. The termination on an interface may consist of any combination of
devices subject only to the requirement that the sum of the RENs of all the devices should not exceed five
(5).
Canadian Emissions Requirements
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus
as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the
Department of Communications.
Cet appareil numérique respecte les limites de bruits radioelectriques applicables aux appareils numériques
de Class A prescrites dans la norme sur le materiel brouilleur: “Appareils Numériques,” NMB-003 edictee
par le ministre des Communications.
Toll Fraud Liability
Be advised that certain security risks are inherent in the use of any telecommunications or networking
equipment, including but not limited to, toll fraud, Denial of Service (DoS) attacks, loss or theft of data,
and the unauthorized or illegal use of said equipment. ADTRAN OFFERS NO WARRANTIES, EITHER
EXPRESSED OR IMPLIED, REGARDING THE PREVENTION, DETECTION, OR DETERRENCE
OF TOLL FRAUD, NETWORKING ATTACKS, OR UNAUTHORIZED, ILLEGAL, OR IMPROPER
USE OF ADTRAN EQUIPMENT OR SOFTWARE. THEREFORE, ADTRAN IS NOT LIABLE FOR
ANY LOSSES OR DAMAGES RESULTING FROM SUCH FRAUD, ATTACK, OR IMPROPER USE,
INCLUDING, BUT NOT LIMITED TO, HUMAN AND DATA PRIVACY, INTELLECTUAL
PROPERTY, MATERIAL ASSETS, FINANCIAL RESOURCES, LABOR AND LEGAL COSTS.
Ultimately, the responsibility for securing your telecommunication and networking equipment rests with
you, and you are encouraged to review documentation regarding available security measures, their
configuration and implementation, and to test such features as is necessary for your network.
Service and Warranty
For information on the service and warranty of ADTRAN products, visit the Support section of the
ADTRAN website at http://www.adtran.com.

Service and Warranty NetVanta 6355 PoE Hardware Installation Guide
8 Copyright © 2013 ADTRAN, Inc. 61200740E1-34F

61200740E1-34F Copyright © 2013 ADTRAN, Inc. 9
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Physical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Power Over Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
SFP Module Slots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Network Interface Modules Supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Voice Interface Modules Supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Shipping Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
NetVanta 6355 PoE Front Panel Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
NetVanta 6355 PoE Rear Panel Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Option Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Network Interface Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Voice Interface Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Unit Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Mounting Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Supplying Power to the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Installing Network and Voice Interface Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Using a USB Cellular Modem with the NetVanta USB WWAN NIM . . . . . . . . . . . . . . . . . . . . . . . . . 40
Installing the NetVanta VPN Accelerator Card (included in P/N 4200368L1) . . . . . . . . . . . . . . . . . . 41
Installing a CompactFlash Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Appendix A. Connector Pin Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Table of Contents NetVanta 6355 PoE Hardware Installation Guide
10 Copyright © 2013 ADTRAN, Inc. 61200740E1-34F

61200740E1-34F Copyright © 2011 ADTRAN, Inc. 11
List of Figures
Figure 1. NetVanta 6355 PoE Front Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 2. NetVanta 6355 PoE Rear Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 3. NetVanta T1/FT1 NIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 4. NetVanta T1/FT1 + DSX-1 NIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 5. NetVanta Dual T1 NIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Figure 6. NetVanta E1/FE1 NIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 7. NetVanta E1/FE1 + G.703 NIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 8. NetVanta ADSL NIM, Annex A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Figure 9. NetVanta USB WWAN NIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 10. NetVanta T1/PRI VIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 11. NetVanta E1/PRI VIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 12. NetVanta Quad FXS VIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 13. NetVanta Quad FXO VIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 14. NetVanta Dual FXS/FXO VIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Figure 15. Wallmount Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Figure 16. NIM/VIM Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Figure 17. NetVanta VPN Card Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Figure 18. CompactFlash Card Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

List of Figures NetVanta 6355 PoE Hardware Installation Guide
12 Copyright © 2011 ADTRAN, Inc. 61200740E1-34F

61200740E1-34F Copyright © 2013 ADTRAN, Inc. 13
List of Tables
Table 1. Front Panel LED Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Table 6-1. CONSOLE Port Pinouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Table 6-2. SFP Slot Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Table 6-3. 10/100Base-T Ethernet Port Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Table 6-4. 1000Base-T Gigabit Ethernet Port Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Table 6-5. T1/E1 Connector Pinouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Table 6-6. DSX-1 Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Table 6-7. G.703 Connector Pinouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Table 6-8. ADSL NIM Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Table 6-9. USB WWAN Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Table 6-10. Analog Station (FXS) and Analog Trunk (FXO) Port Pinouts. . . . . . . . . . . . . . . . . . . . . . . . . 46

List of Tables NetVanta 6355 PoE Hardware Installation Guide
14 Copyright © 2013 ADTRAN, Inc. 61200740E1-34F

61200740E1-34D Copyright © 2011 ADTRAN, Inc. 15
1. INTRODUCTION
This hardware installation guide describes the NetVanta 6355 Power over Ethernet (PoE) unit’s physical
characteristics, lists its features and specifications, introduces basic functionality, and provides installation
instructions.
•Physical Description on page 16
•Product Specifications on page 20
•Option Modules on page 22
•Unit Installation on page 35
For additional information on shipping contents, mounting options, option module installation, and supplying
power the unit, refer to the following sections:
•Shipping Contents on page 16
•Mounting Options on page 36
•Installing Network and Voice Interface Modules on page 39
•Supplying Power to the Unit on page 38
•Using a USB Cellular Modem with the NetVanta USB WWAN NIM on page 40
•Installing the NetVanta VPN Accelerator Card (included in P/N 4200368L1) on page 41
•Installing a CompactFlash Card on page 42
For information on configuration for a specific application, refer to the configuration guides provided on the
ADTRAN Support Community. For details on the command line interface (CLI), refer to the AOS Command
Reference Guide. All other related documents are also available online at http://supportforums.adtran.com.

Physical Description NetVanta 6355 PoE Hardware Installation Guide
16 Copyright © 2011 ADTRAN, Inc. 61200740E1-34D
2. PHYSICAL DESCRIPTION
The NetVanta 6355 PoE is an Integrated Communications Platform (ICP) equipped with 24 PoE (802.3af)
10/100Base-T interfaces capable of supplying the full 15.4 watts and two Gigabit Ethernet interfaces accessed
via a fixed RJ-45 connector or small form-factor pluggable (SFP) slots for fiber connectivity. The
NetVanta 6355 PoE is a 1U-high, rack-mountable metal enclosure that includes a universal AC power supply
and provides Voice over Internet Protocol (VoIP) capability for up to 50 user registrations.
Power Over Ethernet
The NetVanta 6355 PoE interfaces provide the ability to detect attached powered devices (PDs) and deliver
48 VDC to the PD via existing CAT 5 cabling. The PoE interfaces are fully compliant with the IEEE 802.3af
PoE standard. By default, the PoE ports automatically discover and provide power to IEEE-compliant PDs.
SFP Module Slots
The NetVanta 6355 PoE supports two SFP slots that accept a number of industry standard SFP modules. The
SFP modules provide Gigabit Ethernet connectivity over fiber for high-speed uplinks or switch stacking. For a
list of supported SFP modules, visit the ADTRAN website at http://www.adtran.com.
Network Interface Modules Supported
The NetVanta 6355 PoE contains two NIM/VIM slots on the rear panel that support the following modules in
data applications:
• 1202862L1 T1/FT1 NIM
• 1202863L1 T1/FT1 + DSX-1 NIM
• 1200872L1 Dual T1 NIM
• 1200868E1 E1/FE1 NIM
• 1200878E1 E1/FE1 + G.703 NIM
• 1202869E1 ADSL NIM, Annex A
Voice Interface Modules Supported
The NetVanta 6355 PoE NIM/VIM slots on the rear panel support the following VIMs in voice applications:
• 1200690E1 Quad FXS VIM
• 1202691G1 Quad FXO VIM
• 1202692G1 Dual FXS/FXO VIM
• 1200695L1 T1/PRI VIM
• 1200696G1 E1/PRI VIM
Shipping Contents
Each NetVanta 6355 PoE unit is shipped in its own cardboard shipping carton. Open each carton carefully, and
avoid deep penetration into the carton with sharp objects.
After unpacking the unit, inspect it for possible shipping damage. If the equipment has been damaged in transit,
immediately file a claim with the carrier and contact ADTRAN Customer Service (refer to the Repair and
Replacement section of the Support page on the ADTRAN website at http://www.adtran.com/support).

NetVanta 6355 PoE Hardware Installation Guide Physical Description
61200740E1-34D Copyright © 2011 ADTRAN, Inc. 17
Shipments of the NetVanta 6355 PoE include the following items:
• NetVanta 6355 PoE base unit
• Quick start guide
• A detachable power cable with a grounded, three-prong plug
• Mounting brackets and screws
NetVanta 6355 PoE Front Panel Design
The NetVanta 6355 PoE front panel is shown in Figure 1. Table 1 on page 18 describes all of the LEDs, and
Appendix A on page 43 shows the pinouts for the connectors.
Figure 1. NetVanta 6355 PoE Front Panel Layout
NetVanta 6355 PoE Front Panel Features
10/100Base-T Ethernet Interfaces
The NetVanta 6355 PoE front panel contains 24 10/100Base-T Ethernet interfaces (RJ-45). These
interfaces are consecutively numbered 1through 24, from left to right, with the numbers screened
directly above each port. Status LEDs for each of these interfaces are located directly over these
numbers.
The NetVanta 6355 PoE also has green and red PoE status LEDs located in the upper-left and
upper-right corners (respectively) of each Ethernet connector.
Gigabit Ethernet Interfaces/SFP Slots
The NetVanta 6355 PoE front panel contains two Gigabit Ethernet interfaces that provide two fixed
RJ-45 connectors and two standard SFP slots for connectivity over fiber. (Use either the RJ-45
connectors or the SFP slots. The fiber slots have precedence.) These interfaces are labeled G1 and G2,
and the status LEDs are located above the SFP slots.
Status LEDs
The status LEDs are located to the lower left of RJ-45 port 1. The SLOT 1 LED reflects the status of a
NIM/VIM installed in NIM/VIM option SLOT 1 (located on the rear panel). The SLOT 2 LED reflects
the status of a NIM/VIM installed in NIM/VIM option SLOT 2 (located on the rear panel). The STAT
LED indicates the unit’s status.
NetVanta 6355

Physical Description NetVanta 6355 PoE Hardware Installation Guide
18 Copyright © 2011 ADTRAN, Inc. 61200740E1-34D
NetVanta 6355 PoE Rear Panel Design
The NetVanta 6355 PoE rear panel is shown below. Refer to Appendix A on page 43 for pinouts.
Figure 2. NetVanta 6355 PoE Rear Panel Layout
NetVanta 6355 PoE Rear Panel Interfaces
CompactFlash
The CompactFlash slot (labeled CF) supplies nonvolatile configuration and compressed code storage.
The NetVanta 6355 PoE supports only ADTRAN-provided CompactFlash (16 MB to 1 GB) (refer to
the part number on the front cover of this manual).
NIM/VIM Option Slots
The two NIM/VIM option slots (labeled SLOT 1 and SLOT 2) accept a variety of NIM/VIM option
modules (refer to Option Modules on page 22).
FXS and FXO Ports
The two FXS interfaces (labeled ANALOG STA 0/1 and 0/2) and two FXO interfaces (labeled
ANALOG TRK 0/1 and 0/2) provide FXS and FXO connectivity, respectively.
Table 1. Front Panel LED Descriptions
LED Color Indication
STAT Off Unit is not receiving power.
Green (solid) Power is on and self-test passed.
Green (flashing) On power up, the STAT LED flashes rapidly for five
seconds, during which time the user may escape to boot
mode from the CONSOLE port.
Red (solid) Power is on, but the self-test failed or the boot code could
not be booted.
Port LEDs
(1through 24, G1, G2)Off Port is administratively disabled or does not have a
connection.
Green (solid) Port is enabled and has a connection.
Amber (flashing) Port has activity (transmit or receive).
SLOT 1/SLOT 2 Off No NIM/VIM installed or interface is administratively down.
Green (solid) NIM/VIM module is up and everything is okay.
Green (flashing) Port has activity (transmit or receive).
Amber (solid) NIM/VIM module is in test.
Red (solid) An alarm is occurring on the interface.
Power over Ethernet
Status LEDs Green (solid) Power is being applied (48 V) to the interface.
Red (solid) Fault is detected on the interface.
CF
SLOT 1 SLOT 2 ANALOG STA ANALOG TRK
0/1 0/2 0/1 0/2
MOH
NC NO COM
ETH 0/0 CONSOLE
DOOR
RELAY
100-250 VAC
50-60Hz
PAGE

NetVanta 6355 PoE Hardware Installation Guide Physical Description
61200740E1-34D Copyright © 2011 ADTRAN, Inc. 19
During power outages, the FXS interfaces are connected directly to the FXO interfaces. This feature is
called life line mode, and allows customers to make analog calls even when the power is out.
MOH
Reserved for future use.
Page
Reserved for future use.
10/100Base-T Ethernet Interface
The Ethernet port (ETH 0/0) is an RJ-45 connector. The Ethernet port provides the following:
• 10Base-T or 100Base-T with a single connector
• Autonegotiation
• CSMA/CD
• IEEE 802.3 compatibility
Door Relay
Reserved for future use.
CONSOLE Interface
The CONSOLE interface is an EIA-232 serial port (DCE), which provides for local management and
configuration (via a DB-9 female connector).
Power Connection
The rear panel has a power input to the AC universal power supply. Please refer to Supplying Power to
the Unit on page 38 for connection details.
For the NetVanta 6355 PoE, devices connected to the FXS (ANALOG STA) ports must
be ACTA/FCC Part 68 compliant due to the direct connection to the public switched
telephone network (PSTN) in life line mode.
Connection directly to an external modem requires a cross-over cable.

Product Specifications NetVanta 6355 PoE Hardware Installation Guide
20 Copyright © 2011 ADTRAN, Inc. 61200740E1-34D
3. PRODUCT SPECIFICATIONS
• 24-port PoE (802.3af) injector (15.4 watts per port)
• Provides 370 watts of power over spare pair for PoE
• Optional CompactFlash®
• Optional virtual private network (VPN)
• Feature-rich ADTRAN Operating System (AOS)
• Recognizable CLI and user-friendly, Web-based graphical user interface (GUI)
• Telnet, HTTP, SSL, SSH, craft/console port, or SNMP management options
• XAUTH including RADIUS and RSA SecurID
• Flash memory supports dual images of AOS
• TFTP, FTP, and XMODEM for firmware upgrades and maintenance updates
• LLDP (802.1AB) for discovering neighboring peers
• Optional combination SFP/1000Base-T Gigabit Ethernet port for stacking and uplink requirements
• Stacking (up to 16 switches) with single IP address management
• Compatible with ADTRAN’s other VPN-equipped NetVanta products
• Auto-rate, auto-duplexing, and auto-MDI/MDI-X sensing
• Support for VLAN trunking and GVRP with up to 255 active VLANs (802.1Q)
• Class of service (CoS) (802.1p) andDiffServ for traffic prioritization with weightedroundrobin(WRR)
and strict priority queuing
• Four queues per egress port
• DiffServ-to-802.1p mapping
• Spanning Tree/Rapid Spanning Tree support (802.1D/802.1w)
• Storm control, link aggregation (802.3ad), and port mirroring
• MAC-based port security
• Full-featured onboard IP access router supports all NetVanta 3000 Series routing features
• Interchangeable network interface modules (NIMs): T1/FT1, T1/FT1 + DSX-1, Dual T1, and ADSL
Annex A available
• Interchangeable voice interface modules (VIMs): Quad FXS, Quad FXO, Dual FXS/FXO, E1/PRI, and
T1/PRI available
• Standards-based BGP, OSPF, RIP, and static routing support
• Bridging across the WAN
• Ideal for Frame Relay, Multilink Frame Relay, PPP, Multilink PPP (MLPPP), PPPoE, or ATM (ADSL
NIM) networks
• Integral stateful inspection firewall protects against denial of service (DoS) attacks
• Quality of service (QoS) with low latency queuing (LLQ) and weighted fair queuing (WFQ), and
DiffServ marking
• Frame Relay and PPP fragmentation to avoid latency
• VLAN (802.1Q) trunking/interVLAN routing and bridging
• Network address translation (NAT/NAPT) and NAT Traversal version 2
• NAT-compatible SIP ALG
• DHCP client, server, and relay
• IPsec VPN upgrade supporting 500 tunnels and DES/3DES/AES encryption
• Single combination 10/100/1000Base-T Ethernet port/SFP module slot for high-speed uplink or
stacking requirements