ADTRAN T400 Instruction Manual

1Section 61150092L1-5, Issue 561150092L1-5E
Section 61150092L1-5E
Issue 5, June 2001
CLEI Code NDMMBJ01 _ _
ADTRAN 23-Inch T400 Shelf
Installation and Maintenance
Figure 1. 23-inch T400 Shelf
Trademarks: Any brand names and product names included in this document are
trademarks, registered trademarks, or trade names of their respective holders.
1. GENERAL
This practice provides installation and maintenance
procedures for the ADTRAN 23-inch T400 Shelf,
illustrated in Figure 1.
Revision History
Issue 5 clarifies shelf backplane fuse requirements and
updates text format.
Features
The T400 shelf, P/N 1150092L1, supports the
following features and functions:
•Accommodates up to 14 industry standard
T400/T200 circuit packs.
•Meets applicable sections of GR-1089-CORE
and GR-63-CORE for NEBS Level 3
Compliance.
•Provides four 25-pair amphenol connectors.
•Locking front cover.
•Various mounting positions for standard rack
configurations.
•Loss of power alarm relay.
•Front panel electrostatic discharge (ESD)
grounding jack.
General Description
The T400 Shelf is designed to deploy T200/T400
circuit packs. The shelf supports 2-wire, 4-wire, or
two to 4-wire circuit pack form factors for both central
offices and customer premises.
Equipped with mounting flanges, the T400 shelf
installs in a standard 23-inch central office
communications bay. The shelf measures 21 inches
wide, 11 inches deep, and 7 inches high, occupying
four vertical rack units. Two sets of holes on the
mounting flanges allow for positioning the shelf in
either of two standard bay mounting configurations.
The shelf backplane printed circuit board (PCB)
accommodates card edge connectors plus the
interconnects for signals, power, ground, and loss of
power alarm (Figure 2). The backplane of the T400
Shelf contains the following:
•Fourteen 56-pin card edge connectors, one for
each individual circuit pack.
FIGURES
Figure 1. 23-inch T400 Shelf.............................................. 1
Figure 2. 23-inch T400 Backplane ..................................... 2
Figure 3. TS1 Power & Ground Connections .................... 3
Figure 4. TS1 Alarm Connections ......................................3
Figure 5. Telco Connectors ................................................. 5
TABLES
Table 1. Power, Ground, and Data Connections ................. 3
Table 2. Interface Wiring for P1 Through P4 ..................... 4
Table 3. 23-inch T400 Shelf Applications .......................... 6
Table 4. 23-inch T400 Shelf Specifications ........................ 7
CONTENTS
1. GENERAL ..................................................................... 1
2. INSTALLATION ........................................................... 2
3. APPLICATIONS ........................................................... 6
4. SPECIFICATIONS ........................................................ 7
5. MAINTENANCE .......................................................... 7
6. WARRANTY AND CUSTOMER SERVICE ............... 7

2Section 61150092L1-5, Issue 5 61150092L1-5E
•Four 50-pin male amphenol connectors for
input/output signals.
•One loss-of-power relay.
•One five-terminal barrier strip for power,
ground, frame ground, and two Loss-of-Power
Alarm contacts.
2. INSTALLATION
After unpacking the unit inspect it for damage. If
damage is noted, file a claim with the carrier, then
contact ADTRAN. See Warranty and Customer
Service.
After unpacking the shelf, verify the zip-lock bag
contains the following items:
•Four cable tie-wrap mounts.
•Five cable tie-wraps.
•Five #12-24 mounting screws.
•One card and card pouch.
•One key for lockable front cover.
Before installing the T400 Shelf into a bay, remove
any plug-in cards that were shipped with the shelf. To
remove the cards, grasp the faceplate handle and pull.
Temporarily store these units in an area protected
from static electricity.
Mounting
The T400 Shelf is designed to mount directly into a
standard 23-inch wide flange type communications
bay. The T400 Shelf is factory configured to mount 4
inches from the front of the bay. Holes are also
provided for mounting the shelf 5 inches from the
front of the bay. The flanges are easily repositioned
for the applicable mounting arrangement.
Instructions for mounting and electrically connecting
the T400 Shelf in the bay are as follows:
1. Determine the chassis location in the bay.
2. Align the flange mounting holes on each side of
the shelf with the bay mounting holes and
secure with supplied fasteners.
3. Remove the rear cover by disengaging the two
Phillips-head screws.
NOTE
Customer supplied ring-lug wire terminals are
recoáGended for TS1 connections.
4. Insert wires through the cable side entry
grommet before attaching ring-lug terminals.
5. Connect a fused -48 Vdc supply and return, that
is electrically isolated from an AC source, to
-48 V and GND on TS1 (see Figure 3). Fuse
rating depends on the type of circuit cards
deployed. Maximum current for the shelf PCB
is 15 A.
NOTE
Although rated at 15 A, the shelf PCB can be
fused at 5 A if all shelf units are ADTRAN.
C A U T I O N
C A U T I O N
!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
HANDLING PRECAUTIONS REQUIRED.
50 26
25
P3
50 26
125
P1
50
P2
25
125
50 P4 26
125
1
    


J1J2J3J4J5J6J7J8J9J10J11J12J13J14

 
 
Figure 2. 23-inch T400 Backplane

3Section 61150092L1-5, Issue 561150092L1-5E
6. Connect frame ground to TS1 FRAME (see
Figure 3). Because the 48 V return (TS1 GND)
is isolated in the shelf, connect it externally to a
central ground.
7. Connect power alarm contacts to TS1-A and B
(see Figure 4).
8. Provide some slack to ensure that wiring and
terminals are not under strain then tie down the
TS1 wire bundle using the cable tie mount and
wrap provided.
WARNING
Do not dislodge or damage the fiber sheet
insulators on the inside of the cover.
CAUTION
To meet accessibility requirements of
GR-1089-CORE Electrical Safety Criteria, the
rear cover must be installed when span powering
voltages meeting Class A2, A3, AB, B, or C are
present. The front access cover must be installed
when circuit pack design does not prevent
inadvertent contact with non-Class A1 voltage
limits.
9. Replace the shelf rear cover and reinstall the
screws.
10. Determine the routing direction of the
amphenol connector and cable. Insert the cable
tie-wrap mounts into the appropriate holes of
the rear cover, based on the routing direction.
Cable tie-wrap mounts should be located on the
cable side of the amphenol connector.
11. Attach the applicable 50-pin female amphenol
cables to P1, P2, P3, and P4 of the shelf
backplane. See Figure 2. Use the cable tie-wrap
mounts and tie-wraps provided to secure the
cabling.
Power, Ground, & Data Connections
The 14 slot backplane connectors are all identical.
Refer to Table 1 for pinout connections for power,
ground, and tip and ring connections.
Table 1. Power, Ground, and Data
Connections
niPnoitcnuF
1emarFoTdnuorG
5remotsuCot1T
7krowteNot1T
11emarFoTdnuorG
31krowteNot1R
51remotsuCot1R
71nruteRcdV84
53ylppuScdV84-
14krowteNotpiT
74krowteNotgniR
94remotsuCotgniR
55remotsuCotpiT
Figure 4. TS1 Alarm Connections
TO DANTEL
TS1
FRAME
ALARM
-48V
GND AB
Figure 3. TS1 Power & Ground Connections
20 AWG
RING LUG
20 AWG
SOLID 16 AWG
STRANDED
16 AWG
RING LUG
TO FUSE
PANEL
TO WIRE WRAP
FRAME GROUND
TS1
FRAME ALARM
-48V
GND AB
BLK FG
BLK GND
RED -48V

4Section 61150092L1-5, Issue 5 61150092L1-5E
Table 2. Interface Wiring for P1 Through P4
Telco Connectors
Four 50-pin amphenol connectors (P1 through P4) are
provided for the interconnect wiring of the 14 channel
positions. The connector is usually terminated with a
punch-down block for customer premises wiring or
connected directly to a cross-connect or main
distribution frame. Table 2 describes and Figure 5
details the pinout of each connector.
Loss-of-Power Alarm
The T400 Shelf provides an alarm contact which is
open during normal conditions. During a loss of
power the alarm contact will close. The dry contact
closures are rated for 125 Vac at 10 mA and are
designed for connection to a central office alarm
system, such as Dantel.
ESD Grounding Jack
The installer should use the ESD grounding jack
provided at the front of the shelf as a known ground to
prevent ESD during plug-in unit installation.
tiucriC
rebmuN
PMAriaP52
)4P-1P(niP
morF
egdEdraC
rotcennoC
1PoT
morF
egdEdraC
rotcennoC
2PoT
morF
egdEdraC
rotcennoC
3PoT
morF
egdEdraC
rotcennoC
4PoT
eriWPMAriaP-52
)4P-1P(roloC
162
1
)T(14
)R(74
)1T(7
)1R(31
)T(55
)R(94
)1T(5
)1R(51
ULB/THW
THW/ULB
272
2
)T(14
)R(74
)1T(7
)1R(31
)T(55
)R(94
)1T(5
)1R(51
NRO/THW
THW/NRO
382
3
)T(14
)R(74
)1T(7
)1R(31
)T(55
)R(94
)1T(5
)1R(51
NRG/THW
THW/NRG
492
4
)T(14
)R(74
)1T(7
)1R(31
)T(55
)R(94
)1T(5
)1R(51
NRB/THW
THW/NRB
503
5
)T(14
)R(74
)1T(7
)1R(31
)T(55
)R(94
)1T(5
)1R(51
TLS/THW
THW/TLS
613
6
)T(14
)R(74
)1T(7
)1R(31
)T(55
)R(94
)1T(5
)1R(51
ULB/DER
DER/ULB
723
7
)T(14
)R(74
)1T(7
)1R(31
)T(55
)R(94
)1T(5
)1R(51
NRO/DER
DER/NRO
833
8
)T(14
)R(74
)1T(7
)1R(31
)T(55
)R(94
)1T(5
)1R(51
NRG/DER
DER/NRG
943
9
)T(14
)R(74
)1T(7
)1R(31
)T(55
)R(94
)1T(5
)1R(51
NRB/DER
DER/NRB
01 53
01
)T(14
)R(74
)1T(7
)1R(31
)T(55
)R(94
)1T(5
)1R(51
TLS/DER
DER/TLS
11 63
11
)T(14
)R(74
)1T(7
)1R(31
)T(55
)R(94
)1T(5
)1R(51
ULB/KLB
KLB/ULB
21 73
21
)T(14
)R(74
)1T(7
)1R(31
)T(55
)R(94
)1T(5
)1R(51
NRO/KLB
KLB/NRO
31 83
31
)T(14
)R(74
)1T(7
)1R(31
)T(55
)R(94
)1T(5
)1R(51
NRG/KLB
KLB/NRG
41 93
41
)T(14
)R(74
)1T(7
)1R(31
)T(55
)R(94
)1T(5
)1R(51
NRB/KLB
KLB/NRB

5Section 61150092L1-5, Issue 561150092L1-5E
Figure 5. Telco Connectors







































 

 
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 







































 

 
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 







































 

 
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 







































 

 
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
               

6Section 61150092L1-5, Issue 5 61150092L1-5E
Table 3. 23-inch T400 Shelf Applications
tcudorP 1PfOnoitcnuF
)74,14(
2PfOnoitcnuF
)31,7(
3PfOnoitcnuF
)94,55(
4PfOnoitcnuF
)51,5( setoN
hcaeRlatoT
lartneCNDSI
tinUeciffO
morF/oT
krowteN
desUtoNmorF/oT
remotsuC
desUtoNegnaRNDSIeriw-2
noisnetxE
hcaeRlatoT
etomeRNDSI
tinU
morF/oT
krowteN
desUtoNmorF/oT
remotsuC
desUtoNegnaRNDSIeriw-2
noisnetxE
MPR-UmorF/oT
krowteN
morF/oT
remotsuC
desUtoNdesUtoNeciffOlartneCeriw-2
tcudorp
hcaeRlatoT
etomeRSDD
tinU
morF/oT
krowteN
desUtoNremotsuCmorFremotsuCoThcaeRlatoTeriw-2
eriw-4otnoitanimret
stcudorpSDD
ELDIRB
eciffOlartneC
tinU
desUtoNmorF/oT
krowteN
)Uetar-lluF(
morF/oT
remotsuC
1pooL
morF/oT
remotsuC
2pooL
eriw-4otNDSIeriw-2
NDSI
ELDIRB
tinUetomeR
morF/oT
krowteN
2pooL
morF/oT
krowteN
1pooL
desUtoNmorF/oT
remotsuC
)Uetar-lluF(
eriw-2otNDSIeriw-4
noitanimretNDSI
TSDDkrowteNoTkrowteNmorFremotsuCmorFremotsuCoTnoitanimretSDDeriw-4
etomeRLSDH
tinU
krowteN
2pooLLSDH
krowteN
1pooLLSDH
morf1SD
remotsuC
ot1SD
remotsuC
eriw-4otLSDHeriw-4
tcudorp1SD
ERHkrowteN
2pooLLSDH
krowteN
1pooLLSDH
remotsuC
2pooLLSDH
remotsuC
1pooLLSDH
egnaRLSDHeriw-4
rednetxE
USC1TkrowteNoTkrowteNmorFremotsuCmorFremotsuCoTecivres1Teriw-4
TSDAotlatigiD
krowteN
morflatigiD
krowteN
morfgolanA
remotsuC
otgolanA
remotsuC
eriw-4otlatigideriw-4
ecivresgolana
3. APPLICATIONS
Table 3 outlines the various applications intended for
use with the T400 Shelf.

7Section 61150092L1-5, Issue 561150092L1-5E
6. WARRANTY AND CUSTOMER SERVICE
ADTRAN will replace or repair this product within ten
(10) years from the date of shipment if it does not meet
its published specifications or fails while in service.
(See ADTRAN U.S. and Canada Carrier Networks
Equipment Warranty, document 60000087-10).
Contact CAPS prior to returning equipment to
ADTRAN.
For service, CAPS requests, or further information,
contact one of the following numbers:
ADTRAN Sales
Pricing/Availability
[phone]
ADTRAN Technical Support
Pre-sales Applications/Post-sales Technical Assistance
[phone]
Standard hours: Monday-Friday, 7 a.m. - 7 p.m. CST
Emergency hours: 7 days/week, 24 hours/day
ADTRAN Repair/CAPS
Return for Repair/Upgrade
[phone]
Repair and Return Address
ADTRAN, Inc.
CAPS Department
901 Explorer Boulevard
Huntsville, Alabama 35806-2807
Table 4. 23-inch T400 Shelf Specifications
stnemeriuqeRrewoPmetsyS
egatloVCD:tupnI
tnerruCxaM
cdV55-ot24-
lanimoncdV84-
A51
latnemnorivnE
erutarepmetgnitarepO
erutarepmetegarotS
ytidimuhevitaleR
C°07+otC°04-
)F°851+otF°04-(
C°58+otC°04-
)F°581+otF°04-(
gnisnednoc-non,xam%59
lacisyhP
:noisnemiD
:thgieW
,hgih.ni7,gnol.ni11
ediw.ni32
bl21
gnitnuoM
yabsnoitacinummoc.ni32
4. SPECIFICATIONS
The specifications for the T400 Shelf are listed in
Table 4.
5. MAINTENANCE
The T400 Shelf does not require routine maintenance
for normal operation.
ADTRAN does not recommend that repairs be
performed in the field. Repair services are obtained by
returning the defective unit to ADTRAN Customer
and Product Service (CAPS).

8Section 61150092L1-5, Issue 5 61150092L1-5E