ADTRAN U-BR1TE Maintenance and service guide

1Section 61103.020L4-5, Issue 161103.020L4-5A Trademarks: Any brand names and product names included in this document are
trademarks, registered trademarks, or trade names of their respective holders.
1. GENERAL
This practice provides installation and maintenance
informationfortheADTRANU-BR1TE IIIw/PWR. Figure
1is an illustration of the U-BR1TE III w/PWR.
TheU-BR1TE IIIw/PWRisalinecardforuseinaWECO
compatibleD4andanAT&TSLC-96channelbank. The
U-BR1TE III w/PWR incorporates the functionality of a
standard U-BR1TE III and the ADTRAN U-Repeater
Powering Module which will simplify the installation of
ADTRAN U-Repeaters when deployed from a Digital
Loop Carrier (DLC) facility.
The U-BR1TE III w/PWR allows transport of Basic Rate
ISDN over T1 carrier facilities and provides an ISDN
2B1Q U-interface that will supply span power for one of
two modes of operation. In one mode of operation, the
U-BR1TE III w/PWR supplies a constant 43 mA to span
power an ADTRAN ISDN U-Repeater II or U-Repeater
III. Theother modeof operationallows theU-BR1TE III
w/PWR to provide a constant -120 VDC to span power
an ADTRAN I-NIU. The U-BR1TE III w/PWR
automatically determines the appropriate mode of
operation, without requiring an option selection.
Whilethespan powering mode isintendedto be usedin
an Adjacent-to-Customer location, such as a remote
central office or remote terminal, the U-BR1TE III w/
PWR may also be configured for Adjacent-to-Switch
(COT) and Tandem Office applications. Clear channel
capability (B8ZS) is not required of the T1 facility if zero
byte substitution is enabled. The U-BR1TE III w/PWR
plugsintoasingleslotoftheD4andtheSLC-96channel
bank,andtypicallyrequiresthreetimeslotsfortransport
of2B+D information. Block errorrate performance over
the T1 facility is monitored and is available to the
network. The U-BR1TE III w/PWR provides for up to
eighthoursofperformancehistoryforboththeT1carrier
and the U-interfaces.
Revision History
This is the first issue of this practice. Revisions to
subsequent practices will be summarized in this
paragraph.
Section 61103.020L4-5A
Issue 1, March 1997
CLEI Code # D4CIAWT2 _ _
MODEL U-BR1TE III W/PWR
ISDN 2B1Q INTERFACE
INSTALLATION/MAINTENANCE
PRACTICES
C A U T I O N !
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
HANDLING PRECAUTIONS REQUIRED.
Figure 1. ADTRAN U-BR1TE III W/PWR
SW2
SW1
SW3
SW4
UBR1TE III
D4-UBR1 PWR
1103020L4
1 2
NT1
CRTX
LPBK
AD5
AD6
AD3
AD4 AD1
LPTX
AD2
TEST
SW2
B1
SYNC
CRC
SYNC
CRC
ACT
TEST
ERR
B2
NORM PTRN
OUT Rx
LP
L
O
G
I
C
IN Tx
CR
CONTENTS
1. GENERAL........................................................................... 1
2. INSTALLATION ................................................................ 2
3. TESTING............................................................................. 6
4. WARRANTY AND CUSTOMER SERVICE ................... 8
FIGURES
Figure 1. ADTRAN U-BR1TE III W/PWR ................................ 1
Figure 2. Connector Pin Assignments ......................................... 2
Figure 3. Time Slot Assignments for 2B+D Service
in SLC Mode I w/ D1D Counting ............................. 2
Figure 5. Position Switch Settings at Network
Locations .................................................................... 5
Figure 4. SW1, SW3, and SW4 Labeling ................................... 5
TABLES
Table A. Channel Slots that CANNOT Contain
BR1TE Cards ............................................................... 3
Table B. SW1, SW3, and SW4 Option Settings ...................... 4
Table C. Rotary Switch Options.................................................. 6
Table D. LED Indicators.............................................................. 6

2 Section 61103.020L4-5A, Issue 1 61103.020L4-5A
Physical Requirements
The U-BR1TE III w/PWR plugs into a single D4/SLC-96
channel slot. The connector pin assignments are
illustrated in Figure 2. When provisioned for 2B+D
service, the U-BR1TE III occupies three time slots. In a
D4orSLC-96ModeIIIchannelbank,itoccupiesthetime
slot associated with the physical channel slot that it
occupies and the next two time slots to the right. The
Figure 2. Connector Pin Assignments
Features
The U-BR1TE III w/PWR provides Basic Rate (2B+D)
ISDN service to remote locations over existing single
twistedpairwiring. Thefollowingisalistoftheperformance
features offered by the ADTRAN U-BR1TE III w/PWR.
• ISDN 2B1Q interface which meets all Layer 1
requirements as specified in ANSI T1.601-1992.
• Providesrepeaterpowerof43mAat-28to-120VDC.
• Provides 12 mA at -120 VDC for I-NIU.
• 18 kft nominal range on mixed gauge wire 42 dB @
kHz loop loss, 1300 ohms DC resistance design.
• Internal test pattern allows for testing of individual B
channels without requiring external test equipment.
• Transportationof ISDN BasicRate 2B+D information
over T1 facilities in the 3-DS0 format specified in
TR-NWT-000397.
• All Layer 1 maintenance functions.
• Performance monitoring of the Layer 1 facility as
specified in TR-NWT-000397 and TR-TSY-000829.
• DistinctivemetallicDCtestsignaturetoidentifyeither
line unit LT or line unit NT mode of operation as
specified in TR-NWT-000397.
• Provides loopback capability for full 2B+D as well as
individualBchannelsinbothloopandcarrierdirections.
IndividualBchannelloopbacksmaybeinitiatedatthe
U-BR1TE III w/PWR faceplate or from a remote
location through the maintenance channel.
• B1andB2loopbackaddressabilityatthefaceplatefor
the NT1 and up to six devices in the network-to-
customer direction.
• DS0 logic level transmit and receive data access
through faceplate bantam jacks.
• A built-in Cyclic Redundancy Check ( CRC ) clock
errordetectorallowsforlocalperformancemonitoring
at the faceplate without test equipment.
• Addressing and error status with front panel LED
indicators. Testfunctionschosenbyafrontpanelten-
position rotary switch.
• Responds to OCU latching loopback in 2B, B1, and
B2 modes of operation.
The U-BR1TE III w/PWR is fully compatible in
functionality and is interchangeable with the following
units: U-BR1TE (1100.020L1, L3), U-BR1TE II
(1102.020L2), U-BR1TE II w/PWR (1102.020L4), and
the U-BR1TE III (1103.020L2).
2. INSTALLATION
After unpacking the unit, immediately inspect it for
possibleshippingdamage. Ifdamageisdiscovered,file
a claim immediately with the carrier, then contact
ADTRAN Customer Service (see subsection 6). To
install the U-BR1TE III w/PWR, grasp the unit by the
faceplateand insertitintothebackplaneconnectoruntil
firmly seated. The faceplate latch will automatically
secure itself to the channel bank.
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
FRM GND
-12V
GND
+12V
GND
TWD
TSP
TSQ
RNPCN
TDCLK
NGATE
RSP
RNDIS
-48R
NSEIZE
T*
MCLK
+5V
INCLK
TDATA
RCLK
RWD
RSQ
-48V
R*
GND
*2B1Q Signal
Terminals
physicalchannel slots, whose timeslots are usedin this
manner, must remain unoccupied.
In an SLC-96 Mode I with D1D counting channel bank,
thetimeslotsareallocatedasshowninFigure3withtwo
time slots per physical channel slot.
The unit uses two time slots in one physical slot and a
timeslotfromanadjacentslotwhenconfiguredfor2B+D
operation. WhenoptionedforSlot1,4,7,or10operation,
the unit occupies the two time slots associated with the
physical slot in which it resides and the upper time slot
of the next adjacent physical slot.
When optioned for Slot 2, 5, 8, or 11 operation, the unit
occupiesthelowertimeslotoftheoccupiedphysicalslot
and the adjacent two time slots of the next physical slot
totheright. WhenusingtheSlot2,5,8,or11option,the
Figure 3. Time Slot Assignments for 2B+D
Service in SLC Mode I w/ D1D Counting
PS1 PS2 PS3 PS4 PS5 PS6 PS7 PS8 PS9 PS10 PS11 PS12
UTS
C1
LTS
UTS
*
LTS
UTS
C2
LTS
UTS =
C1 =
C2 =
upper time slot
physical location of U-BR1TE
optioned as "slots 1, 4, 7, 10"
physical location of U-BR1TE
optioned as "slots 2, 5, 8, 11"
LTS =
PS =
* =
lower time slot
physical slot
(1 physical slot consists of 2 time slots)
Must be empty - time slots are being used
by U-BR1TE card in C2
C1 C2 C1 C2 C1 C2
Unoccupied Unoccupied Unoccupied

3Section 61103.020L4-5, Issue 161103.020L4-5A
physical slot to the right must be left vacant. A unit
optionedforoneor two timeslots,B1+D,B2+D, B1, B2,
2B, and D only, occupies only the two time slots
associated with the physical slot used. In this
configuration, option the unit for Slot 1, 4, 7, or 10. See
TableAforadditionalchannelslotdeploymentrestrictions
for each bank type.
D4 Bank Requirements
The COT D4 bank must be configured with an OIU-2
optioned for external timing. The COT bank must be
providedwithanexternalcompositeclocksynchronized
with the network.
SLC Bank Requirements
The COT SLC bank must be configured with a special
service unit (SSU) optioned for external timing. The
COT SLC bank must be provided with an external
composite clock synchronized with the network.
Interface Requirements
The U-BR1TE III w/PWR unit includes two interfaces.
The loop-side interface is an ISDN U-interface which is
used to deliver Basic Rate service. The carrier-side
interface is a D4/SLC-96 channel bank interface which
is used to insert data into the 1.544 Mbps T1 stream.
Only the polarity-insensitive T and R leads are used in
the cross-connection. When deployed in a SLC-96
channelbank,theU-BR1TEIIIw/PWR U-interfacepins
out on the “odd” pair of the physical slot where it is
located.
Option Switch Settings
TableBcontains theoptionsettingsforSW1,SW3,and
SW4. Figure 4 displays the locations for SW1, SW3,
and SW4.
Table A. Channel Slots that CANNOT Contain BR1TE Cards
Type of Service
D
B1+D or B2+D (*)
2B+D (**)
D4 Bank with
D4 Counting
---
24
23, 24
SLC-96 Mode I with
D1D Counting
---
---
6, 12
D4 Bank with D1D Counting
or SLC-96 Mode III
with D4 Counting
---
12, 24,
11, 12, 23, 24
SLC-96 Mode III
with D1D Counting
---
6, 12, 18, 24,
5, 6, 11, 12, 17, 18,
23, 24
123456789101112
123456789101112
13 14 15 16 17 18 19 20 21 22 23 24
13 14 15 16 17 18 19 20 21 22 23 24
Physical Slots
Time Slots
Physical Slots
D4 Bank:
D4 Channel
Counting
123456789101112
1 5 9 1317212 6 10141822
3 7 11 15 19 23 4 8 12 16 20 24
Physical Slots
Time Slots
SLC-96
Mode 1:
D1D Channel
Counting
123456789101112
1 5 9 1317 212 6 10141822
3 7 11 15 19 23 4 8 12 16 20 24
13 14 15 16 17 18 19 20 21 22 23 24
Physical Slots
Time Slots
Physical Slots
SLC-96
Mode 3:
D1D Channel
Counting
123456789101112
2 4 6 8 10 12 14 16 18 20 22 24
1 3 5 7 9 11 13 15 17 19 21 23
13 14 15 16 17 18 19 20 21 22 23 24
Physical Slots
Time Slots
Physical Slots
D4 Bank:
D1D Channel
Counting, or
SLC-96
Mode 3:
D4 Channel
Counting
****
** **
**
**
**
**
**
**
**
**
**
**
**
**
**
*
*
*
*
*
A channel unit with B+D service cannot occupy this slot
A channel unit with 2B+D service
cannot occupy this slot
**
*

4 Section 61103.020L4-5A, Issue 1 61103.020L4-5A
Function dependent upon SW3-1 setting in non-powering configuration.
Function is not applicable in powering configuration (SW-4 to Power).
Table B. SW1, SW3, and SW4 Option Settings
LABEL
TRM
TRM
B1
B2
D
ZBS DIS
ZBS EN
LULT(RT)
LUNT(COT)
ADJ
TANDEM
ADJ
TANDEM
NORM
POWER*
FUNCTION
Bank Type Selection
Service Level Selection
Zero Byte Substitution
Disables ZBS
Enables ZBS
Termination Mode
LULT mode (RT typical)
LUNT mode (COT typical)
(See figure 5)
LULT Mode (SW3-1
On )
DC sealing current provided
DC sealing current not provided
LUNT Mode (SW3-1 Off )
Periodic wake-up tone not provided
Periodic wake-up tone provided
Normal
Powering provided toward the
customer U-interface.
SWITCH
SW1-1
SW1-2
SW1-3
SW1-4
SW1-5
SW 1-6
On*
Off
SW 3-1
On*
Off
SW 3-2
On*
Off
On
Off
SW4
* Factory default settings
DESCRIPTION
Selects the bank type for the U-BR1TE III w/PWR.
Bank Count/Slot SW1-1 SW1-2
D4 ............... D4 Counting*.................. On........ Off
D1D Counting ................ On........ On
SLC I........... CU in slots 1,4,7,10 ....... On........ On
CU in slots 2,5,8,11 ....... Off........ Off
SLC III......... D4 Counting ................... On........ On
D1D Counting ................ Off........ On
Selects the service level. The U-BR1TE III w/PWR may be
optioned to deliver full ISDN (2B+D) or any other level of
service. SW1-3 SW1-4 SW1-5
Service Option B1 B2 D
2B+D* ........................... On ........... On .............On
2B ................................. On ........... On .............Off
B1+D............................. On ........... Off .............On
B2+D............................. Off ........... On .............On
B1 ................................. On ........... Off .............Off
B2 ................................. Off ........... On .............Off
D ................................... Off ........... Off .............On
The ZBS option must be set the same for the COT and RT.
SW1-6 should be set toward “ZBS EN” for AMI-provisioned
carriers. The switch setting is optional for B8ZS-provisioned
carriers. Consult local provisioning guidelines.
This switch should be set toward “LULT” when the unit is
installed as Adjacent-to U-Repeater/I-NIU, Adjacent-to-
Customer, or Tandem Office Source configuration. This
switch should be set toward “LUNT” for Adjacent-to-Switch
and Tandem Office Sink configurations.
In the LULT(RT) mode, SW3-2 controls sealing current.
WhenusedinanAdjacent-to-Customerconfiguration,sealing
current should be provided (SW3-2 On ). In a Tandem Office
Source,sealingcurrentis not required,andshouldbedisabled
(SW3-2 Off ).
In the LUNT(COT) mode, SW3-2 controls periodic wake-up
tone. Periodic wake-up tones should be disabled when
locatedinanAdjacent-to-Switchlocation(SW3-2 On ). Periodic
wake-up tones are required (SW3-2 Off ) when located in a
Tandem Office Sink configuration, or when adjacent to a
devicerequiringwake-uptones,suchasaNewbridge®switch.
No powering provided toward the customer U-interface.
Automatically determines which of the following modes of
operation is appropriate:
• Supply a constant 43 mA to power an ADTRAN
ISDNU-Repeater II or U-Repeater III.
• Supply a constant -120 VDC to power an ADTRAN I-NIU.
Note: PoweroptionshouldonlybeusedintheLULT
(RT) configuration

5Section 61103.020L4-5, Issue 161103.020L4-5A
recessed push-button, a rotary switch, a
bantam jack, and LEDs, as illustrated in
Figure1. TheB1/B2 DIP Switch selectsthe
desired bearer channel, B1 or B2, to be
tested during local tests using the
U-BR1TE IIIw/PWR faceplate. TheNORM/
PTRN DIP Switch selects between normal
and internal 2047 pattern generator local
test. The ten-position rotary switch is used
to determine the specific test that will be
performed,includingdownstreamloopbacks
Faceplate Features
The U-BR1TE III w/PWR faceplate features a two-
position Dual In-line Package (DIP) Switch, a
(See Table C). LED indicators display the current
status of the unit, as listed in Table D.
Figure 5. Position Switch Settings at Network Locations
ISDN
Switch
D4
Channel
Bank
Customer
NT1
D4/SLC-96
RT
Channel
Bank
2-Wire
2-Wire T Carrier T Carrier 2-Wire
Loop
Adjacent to
Switch Tandem Office
(Source) Tandem Office (Sink) Adjacent to Customer
D4
Channel
Bank
D4/SLC-96
COT
Channel
Bank
L
U
L
T
L
U
L
T
L
U
N
T
L
U
N
T
1 LULT (RT)
2 TANDEM
SW3
1 LUNT (COT)
2 ADJ
SW3 1 LUNT (COT)
2 TANDEM
SW3 1 LULT (RT)
2 ADJ
SW3
Norm*
SW4
Norm*
SW4 Norm*
SW4 Norm*
SW4
D4/SLC- 96
COT
Channel
Bank
D4/SLC-96
RT
Channel
Bank
2-Wire T Carrier 2-Wire
Loop
Adjacent to
Switch Adjacent to
Customer
L
U
L
T
L
U
N
T
1 LUNT (COT)
2 ADJ
SW3 1 LULT (RT)
2 ADJ
SW3
Norm*
SW4 Norm*
SW4
Customer
NT1
Note: Refer to the bottom of Table B
to interpret switch settings.
* SW4 Only pertains to 1103.020L4.
Norm*
SW4 Power*
SW4
D4/SLC-96
COT
Channel
Bank
2-Wire T Carrier
Adjacent to
Switch Adjacent to
U-Repeater/I-NIU
D4/SLC-96
RT
Channel
Bank
L
U
L
T
L
U
N
T
1 LUNT (COT)
2 ADJ
SW3 1 LULT (RT)
2 ADJ
SW3
2-Wire
Loop
2-Wire Customer
NT1
RP
Figure 4. SW1, SW3, and SW4 Labeling
1
TRM B1 B2 D ZBS DIS
1
O
N2
23456
O
N
ZBS EN
LUNT(COT)
1
TRM B1 B2 D ZBS DIS
23456
O
N
ZBS EN
1
O
N2
LUNT(COT)
SW1
SW3
TANDEM
LULT(RT) ADJ
TANDEM
SW3
LULT(RT) ADJ
SW2
NORM
SW4
POWER
NORM POWER
SW4

6 Section 61103.020L4-5A, Issue 1 61103.020L4-5A
1. Select the desired loopback address using the ten-
position rotary switch. Refer to Table C.
2. Select the desired bearer channel using the B1/B2
DIP switch.
3. Select PTRN on the NORM/PTRN DIP switch.
4. Depress the recessed TEST push-button to initiate
the test. The TEST LED will illuminate GREEN
when the loopback is established to the selected
address, and the ERR LED should go out following
synchronization to the test pattern. If the selected
addressdoesnotrespond,theTESTLEDwillremain
out and the ERR LED will illuminate.
3. TESTING
The U-BR1TE III w/PWR responds to embedded
operation channel loopbacks, including B1, B2, and
2B+D, when configured for D channel operation. When
used in non-D channel modes of operation (B1, B2, or
2B),theAdjacent-to-CustomerU-BR1TEwillrespondto
theinbound OCU Latching loopback sequence for each
B-Channel. When remote testing is not available, or
during sectionalization of trouble or equipment
malfunction,theU-BR1TE IIIw/PWRfaceplateprovides
localcapabilities. Usingtheinternal2047pseudorandom
test pattern generator or the bantam jacks allows
craftpersonstotestinboththedownstreamandupstream
directions, including loopback for 6 addressable ISDN
devices and the customer’s NT1.
The faceplate bantam jacks accommodate standard DS0
LogicTesterssuchastheTPI108/109RTIIorFIREBERD
4000/6000 which perform both the upstream and the
downstream testing.
Loopback Tests (ADR1 - ADR6, NT1)
Loopbacks in the network-to-customer direction can be
initiated from either the ISDN switch or the faceplate.
Either the internal 2047 test pattern or a DS0 digital test
set provide the 64kbs bit test pattern to be tested in B1
orB2. WheninitiatingloopbacksfromtheU-BR1TE III w/
PWRfaceplate,thedownstreamdirectionisautomatically
selected based on the card position in the network. To
initiate a loopback using the internal 2047 test pattern,
perform the following:
DISPLAY
AD1
AD2
AD3
AD4
AD5
AD6
LPBK
CRTX
LPTX
NT1
INTERPRETATION
Address #1, address of this unit
Address #2, the next downstream unit away
Address #3, the second unit downstream
Address #4, the third unit downstream
Address #5, the fourth unit downstream
Address #6, the fifth unit downstream
Loopback, forces this unit to loopback either
B1/B2 from the front panel. Loopbacks occur
in both the customer and network directions.
Carrier transmit, in the carrier direction
Loop transmit, in the loop direction
NT1, address of the NT1
Table C. Rotary Switch Options Table D. LED Indicators
DISPLAY
LP SYNC
(Loop Sync)
LP CRC
(Loop CRC )
CR SYNC
(Carrier Sync)
CR CRC
(Carrier CRC)
ACT
(ACT Bit)
TEST
ERR
COLOR
Red
Red
Red
Red
Green
Green
Yellow
Red
INTERPRETATION
U-interface is out of sync.
In normal mode, Flashes upon
receipt of NEBE from the loop.
In Local Performance Monitoring:
Flashes when 6-19 CRC errors are
detected from the loop.
Solid when 20 or more CRC errors
are detected from the loop.
Invalid TR-397 framing over the T1
carrier facilities.
In normal mode, Flashes upon
receipt of NEBE from the T1
In Local Performance Monitoring:
Flashes when 6-19 CRC errors are
detected from the T1.
Solid when 20 or more CRC errors
are detected from the T1.
Customer NT1 successfully
exchangingACTbitswiththenetwork.
Solid when internal 2047 test has
successfully looped the selected
remote, during internal 2047 in
LPTX or CRTX test, or in Local
Performance Monitoring.
Flashes once per second in
response to a EOC B1 loopback.
Flashes twice per second in
response to a EOC B2 loopback.
Solid in response to EOC 2B+D
loopback and during DS0 logic test
whentheremoteunithassuccessfully
looped, or in LPTX or CRTX.
Flashes whena bit erroris received
duringtheinternal2047testpattern.
Solid whenunithasencounteredan
error while in test mode.

7Section 61103.020L4-5, Issue 161103.020L4-5A
5. To insert one bit error, momentarily (for less than 2
seconds)depressthe TEST push-button. TheERR
LED should flash upon receipt of the injected error.
6. Tests to additional network addresses may be
performed by changing the selector knob to the
desired address. It is not necessary to exit the test
mode to select a new address.
7. Todeactivatetheloopback,depresstheTESTpush-
buttonfor2seconds, until the GREEN TESTLEDis
extinguished, or select NORM on the NORM/PTRN
DIP switch.
To initiate a loopback using a DS0 digital test set,
perform the following:
1. InserttheTXandRXbantamplugsoftheDS0digital
testsetintotheU-BR1TE IIIw/PWRrespectivefront
panel bantam jacks. Connect the clock input of the
DS0 digital test set to the channel bank’s clock
source (D4’s OIU, or the SLC-96 SSU). Configure
the test set for Near Logic and 64kbps.
2. Select the desired loopback address using the ten-
position rotary switch. Refer to Table C.
3. Select the desired bearer channel using the B1/B2
DIP switch.
4. Depress the recessed TEST push-button to initiate
the test. The TEST LED will illuminate YELLOW
when the loopback is established to the selected
address. If the selected address does not respond,
the TEST LED will remain out. Observe the DS0
digital test set for bit errors.
5. Tests to additional network addresses may be
performed by changing the selector knob to the
desired address. It is not necessary to exit the test
mode to select a new address.
6. Todeactivatetheloopback,depresstheTESTpush-
button or remove the transmit bantam plug. Upon
deactivation of the test, the TEST LED will go out.
Point-to-Point Test (CRTX, LPTX)
Apoint-to-point(straight-away)testcanbeperformedto
either the U-interface (LPTX) or the T1 carrier interface
(CRTX). In both cases either the internal 2047 test
patterngeneratororaDS0digitaltestsetisusedtoverify
the performance of the selected bearer channel. To
initiate a point-to-point test using the internal 2047 test
pattern, perform the following:
1. Selectthedesiredtestdirection,LPTXorCRTX,using
the ten-position rotary switch. Refer to Table C.
2. Select the desired bearer channel using the B1/B2
DIP switch.
3. Select PTRN on the NORM/PTRN DIP switch.
4. Depress the recessed TEST push-button to initiate
the test. The TEST LED will illuminate GREEN and
theERRLEDshouldgooutfollowingsynchronization
to the test pattern from the far end.
5. IfthefarendunitisaU-BR1TE IIIw/PWR,usingthe
internal 2047 test pattern, perform steps 1-4,
choosing the same faceplate switch setting. If the
farendisatestset,ensureitisconfiguredfora2047
test pattern.
6. To insert one bit error, momentarily (for less than 2
seconds)depresstheTESTpush-button. Biterrors
will be seen at the far end test unit.
7. Todeactivatetheloopback,depresstheTESTpush-
buttonfor2seconds, until the GREEN TESTLEDis
extinguished, or select NORM on the NORM/PTRN
DIPswitch. Upondeactivationofthetest,theTEST
LED will go out.
To initiate a point-to-point test using a DS0 digital test
set, perform the following:
1. InserttheTXandRXbantamplugsoftheDS0digital
testsetintotheU-BR1TE IIIw/PWRrespectivefront
panel bantam jacks. Connect the clock input of the
DS0 digital test set to the channel banks clock
source (D4’s OIU, or the SLC-96 SSU). Configure
the test set for Near Logic and 64kbps.
2. Selectthedesiredtestdirection,LPTXorCRTX,using
the ten-position rotary switch. Refer to Table C.
3. Select the desired bearer channel using the B1/B2
DIP switch.
4. Depress the recessed TEST push-button to initiate
the test. The TEST LED will illuminate YELLOW.
5. If the far end unit is a U-BR1TE III w/PWR using a
DS0digitaltest set, performsteps1-4,choosingthe
samefaceplateswitchsetting. Ensurethatbothtest
sets are configured for the same test pattern (511,
2047). If the far end unit is a U-BR1TE III w/PWR
usingtheinternal2047testpattern,performsteps1-
4 of the previous section.
6. Observe the DS0 digital test set for bit errors.
7. Todeactivatetheloopback,depresstheTESTpush-
button, or remove the transmit bantam plug. Upon
deactivation of the test, the TEST LED will go out.
Local Loopback (LPBK)
AbilateralloopbackcanbeinitiatedfromtheU-BR1TE III
w/PWR faceplate for either bearer channel. A test
pattern source is not required for this test. To initiate a
local loopback, perform the following:
1. Select the desired bearer channel using the B1/B2
DIP switch.
2. Select LPBK using the ten-position rotary switch.
Refer to Table C.
3. Depress the recessed TEST Push-button to initiate
the test. The TEST LED will flash YELLOW to
indicate B1 or B2.
4. Todeactivatetheloopback,depresstheTESTpush-
button. Upondeactivationofthetest,theTESTLED
will go out.

8 Section 61103.020L4-5A, Issue 1 61103.020L4-5A
Local Performance Monitoring
PerformanceMonitoring ofthelocalT1carriersystemand
2-wireU-interfaceoftheISDNdatacanbeperformedfrom
thefrontpanelwithoutinterruptionofservicetothecustomer.
Forthistest,bearerchannelselectionisnotapplicableand
a test pattern source is not required. To initiate local
performance monitoring, perform the following:
1. EnsuretheNORM/PTRNDIPswitchisintheNORM
position, and that a bantam plug is NOT installed in
the faceplate TX bantam jack.
2. Select ADR1 using the ten-position rotary switch.
3. Depress the recessed TEST Push-button to initiate
the test. The TEST LED will illuminate GREEN.
4. The total number of Near End Block Errors (NEBE)
receivedaresimultaneouslydisplayedas CRC errors
withtheLPandCRCRCstatusLEDs. (SeeTableD).
5. To exit Local Performance monitoring, depress the
TEST button for 2 seconds or longer. Upon
deactivation of the test, the TEST LED will go out.
Leased Mode Testing (B1, B2, and 2B)
Forleased mode applications, the D channel istypically
disabled on the U-BR1TE III w/PWR. Without the D
channel, standard ISDN loopbacks by way of the EOC
are not available across the T1 carrier system. For this
situationtheADTRANU-BR1TE IIIw/PWRrespondsto
independent network-issued OCU latching loopback
sequences for B1 and B2, when configured as the
Adjacent-to-Customer.
Enabling OCU latching loopback sequence:
1. Minimum of 35 transition in progress (TIP) bytes
(*0111010).
2. Minimum of 35 loopback select code (LSC) bytes
(*1010101).
3. Minimum of 100 loopback enable (LBE) bytes
(*1010110).
4. Minimumof32far-endvoice(FEV)bytes(*1011010).
* Denotes Don’t Care bit -- either a 1 or a 0.
Disabling OCU latching loopback sequence:
1. Minimum of 35 TIP bytes.
The valid front panel tests in leased modes are ADR1,
CRTX, LPTX, and LPBK for all circuit positions. NT1,
ADR1-ADR6 loopback tests are valid for the Adjacent-
to-Customer circuit position only. ADR2 would be used
to test an ADTRAN U-Repeater deployed from the
U-BR1TE III w/PWR.
Local Performance Monitoring is available only for the U-
interface,whenconfiguredforaleasedmodeofoperation.
See the subsections entitled Loopback Tests , Point-to-
Point Test , and Local Loopback for applicable test
descriptions.
4. WARRANTY AND CUSTOMER SERVICE
ADTRAN will replace or repair this product within ten
years from the date of shipment if this product does not
meet its published specifications or if it fails while in
service. For detailed warranty, repair, and return
information, refer to the ADTRAN Equipment Warranty
and Return Policy Procedure.
Return Material Authorization (RMA) is required prior to
returning equipment to ADTRAN. ADTRAN does not
recommend that repairs be performed in the field.
ForService,RMArequests,orfurtherinformation,contact
one of the following numbers:
ADTRAN Customer Service:
Telco Technical Support [phone]
Standard support hours: Monday-Friday
7 a.m. - 7 p.m. CST
Emergency support: 7 days/week, 24 hours/day
Sales [phone]
RMA (repair service) [phone]
Repair and Return Address:
ADTRAN, Inc.
Customer Service Department
901 Explorer Boulevard
Huntsville, Alabama 35806-2807