ADURO Hybrid User manual

Technical maintenance of Aduro Hybrid
The technical maintenance must be conducted by a professional. The chimney must
be maintained and swept according to local rules.
The Aduro Hybrid stove must be inspected after one year for cleaning and potential
adjustment. Hereafter, maintenance must be conducted by an Aduro certified
professional every other year or for every 2,000 kg pellets burned.
First year maintenance:
•Chimney sweeping –this must be conducted by the local and qualified chimney
sweeper. Control the smoke pipes and smoke outlet for any humidity.
•Control the isolation tiles by taking them off, vacuum and take out the ashes,
clean the burning chamber and metallic baffle plate.
•Check the burning cave and cast iron grid is sitting properly without leakage,
clean if dirty and make sure air pathways are free.
•Check that the fan is working properly and clean the rotor blades if necessary.
•Empty the pellet container and vacuum the bottom of the external auger through
the opening in the pellet container.
•Take out the motherboard cautiously and clean it carefully if there I dust.
•Check the door is tight and glass gaskets. Adjust the glass fittings.
•Vacuum clean the internal auger and remove it. Check that the rubber O ring is
intact.
•Remove the ceramic igniter and check for ashes in the white cylinder. Clean it if
there are ashes.
•Check if the stove has any marks and give it some senotherm if necessary, for a
fresh new look.
Control and adjustment:
•Install the newest software.
•Check the function of the door switch and the switch for the air damper.
•Make sure that the grey air damper located in the middle of the stove is pushed
all the way in when burning with pellets and must only be pulled when burning
with wood.
•Check the door is tight and adjust it if necessary.
Restart of the stove:
•Fill the augers with pellets until you see visible pellets 1cm below the edge of the
short auger tube at the burning cave.
•Control that the stove ignites correctly in the 1 attempt.
Technical maintenance after year 1:
Maintenance must be conducted by an Aduro certified professional every other year
or for every 2,000 kg pellets burned.
•Conduct the same service as written above under First year maintenance and
replace the internal gear motor when you clean the internal auger.
•Check number of ignitions and change the electrical igniter if more than 3000
ignitions have been made.
Replacement:
•Dismount the internal auger and gearbox and check for “abnormal” wear.
•Replace the internal gearmotor and control the O-ring gasket.

Normal maintenance –frequency depending on number of hours in operation:
See user manual and Aduro Customer Service for guidance. Vacuum clean the burning cave and the
top of the internal auger.
Periodic maintenance –after approx. 500 hours in operation:
•Brush the inside of the pellet container.
•Vacuum clean the burning cave and internal auger.
•Check the fan and brush/clean the rotor blades.
•Clean the burning cave and grate for cinders, e.g. with a scraper.
•Clean the air pathway for the electrical igniter from the auger.
•Clean for dust in the top of the stove above the baffle plate. The baffle plate in vermiculite can be
lifted or removed. If you remove the baffle plate, you must remove the other vermiculite tiles first.
See Aduro Customer Service for guidance. Use a vacuum cleaner for cleaning.
How to change the internal gearmotor:
NB:
The hybrid stoves from the series going from production number 17H10114 to
17H10210 do not have the O-ring between the motor and the internal auger.
This O-ring helps prevent ash from pellets going on the engine. It is therefore
necessary to mount the ring within the internal gear motor during the yearly visit.
Instructions:
1. Unplug the stove.
2. Remove the internal auger and its motor according to the attached film:
https://www.youtube.com/watch?v=cvFp7qOh53M&list=PL5Ss_Yw6SykkagmwLY
EunXgsRd4QGPw1u&index=9.
3. Mount the O-ring on the internal gear motor (see photos below).
4. Insert the auger and the auger motor to its location like shown in the video.
5. Restart the stove.