Advance acoustic ALL CLEANER User manual

INSTRUCTIONS FOR USE AND PARTS LIST
MODELS: 56380772, 56381594
2/10 revised 1/11 Document Number 56380890
ALL CLEANER, ALL CLEANER XP

2 - FORM NO. 56380890
IMPORTANT SAFETY INSTRUCTIONS
This machine is only suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and offices other
than normal residential housekeeping purposes.
When using any electrical appliance, basic precautions should always be followed, including the following:
NOTE: Read all instructions before using this machine.
WARNING!
To reduce the risk of fire, electric shock, or injury:
Always use the power cord that comes with the machine and includes a GFCI (Ground Fault Circuit Interrupter). Never use the
machine without connecting to power through a GFCI.
Do not leave the machine when it is plugged in. Unplug the unit from the outlet when not in use and before servicing.
To avoid electric shock, do not expose to rain or snow. Store and use indoors.
Do not allow to be used as a toy. Close attention is necessary when used near children.
Use only as described in this manual. Use only the manufacturer’s recommended attachments.
Do not use with a damaged cord or plug. If the appliance is not working as it should, has been dropped, damaged, left outdoors, or
dropped into water, return it to a service center.
Do not pull by the cord, use the cord as a handle, damage the cord, or allow the cord or the machine near heated surfaces.
Do not unplug by pulling on the cord. To unplug, grasp the cord end.
Do not handle the plug, the cord, or the machine with wet hands.
Do not put any objects into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may
reduce air flow.
Keep loose clothing, hair, fingers, and all parts of your body away from the openings and moving parts.
Do not pick-up anything that is burning or smoking, or any health endangering dusts.
Turn off all controls before unplugging.
Always use chemicals with a pH between 4 and 12, and never introduce the chemcials in the tank. Always use the chemical
siphoning system.
Use extra care when cleaning on stairs.
Do not use to pick up flammable or combustible liquids, and do not use in any areas where these may be present.
If foam or liquid comes out with the vacuum exhaust, switch the power off immediately. Verify that there are not foreign objects from
preventing the float ball from moving freely. Contact Advance if the problem persists.
Liquid ejected at the spray nozzle could be dangerous as a result of its temperature, pressure, or chemical content.
SAVE THESE INSTRUCTIONS
WARNING!
The Products sold with this Manual contain or may contain chemicals that are known to certain governments (such as the State of
California, as identified in its Proposition 65 Regulatory Warning Law) to cause cancer, birth defects or other reproductive harm. In
certain locations (including the State of California) purchasers of these Products that place them in service at an employment job site
or a publicly accessible space are required by regulation to make certain notices, warnings or disclosures regarding the chemicals that
are or may be contained in the Products at or about such work sites. It is the purchaser’s responsibility to know the content of, and to
comply with, any laws and regulations relating to the use of these Products in such environments. The Manufacturer disclaims any
responsibility to advise purchasers of any specific requirements that may be applicable to the use of the Products in such environments.
revised 1/11

FORM NO. 56380890 -3
INTRODUCTION
This manual will help you to get the most from your Advance All Cleaner. Read it thoroughly before operating the machine.
This product is intended for commerical use only.
PARTS AND SERVICE
Repairs, when required, should be performed by Advance service personnel using original replacement parts and accessories. Call Advance for repair
parts or service.
Please specify the Model and Serial number when calling about your machine.
NAME PLATE
The model and serial number of your machine are shown on the Name Plate on the machine.
This information is needed when ordering parts for the machine.
Use the space below to note the model and serial numbers of your machine.
MODEL NUMBER/NAME: __________________________________________________
SERIAL NUMBER: ________________________________________________________
UNPACKING
When the machine arrives, carefully inspect the shipping carton and the machine for damage. If damage is evident, save the shipping carton so that it
can be inspected by the carrier. Contact the Advance customer service department immediately to file a freight damage claim.
DO NOT OPERATE THE MACHINE UNTIL YOU HAVE READ THIS SECTION
IMPROPER USE WILL VOID THE WARRANTY
Always use a defoamer when foaming occurs to prevent vacuum motor damage.
To keep fittings, pumps, and lines from damage during freezing conditions, use RV anti-freeze in the pump or keep the machine inside heated
areas.
Do not let the pump run dry.
All chemicals should be added through the feed system and NOT in the tank.
All extension cords must have a rating of at least 12/3 (12 gauge cord). Extension cords should be no longer than 50 feet. Replace the plug
immediately if the ground prong becomes damaged or is broken off.
DO NOT use water heated to greater than 120 °F (54 °C).
120VAC GROUNDING INSTRUCTIONS
This appliance must be grounded. If it should electrically malfunction, grounding provides a path of least resistance for electric current to reduce the risk
of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into
an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
DANGER!
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or
service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance. If it
will not fit the outlet, have a proper outlet installed by a qualified electrician.
This appliance is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in Figure 1 below. A temporary
adapter illustrated in Figures 2 and 3 may be used to connect this plug to a 2-pole receptacle as shown in Figure 2 if a properly grounded outlet is not
available. The temporary adapter should be used only until a properly grounded outlet (Figure 1) can be installed by a qualified electrician. The green-
colored rigid ear, tab, or the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover.
Whenever the adapter is used, it must be held in place by a metal screw. Grounding adapters are not approved for use in Canada.
Replace the plug if the grounding pin is damaged or broken.
The Green (or Green/Yellow) wire in the cord is the grounding wire. When replacing a plug, this wire must be attached to the grounding pin only.
Extension cords connected to this machine should be 12 gauge, three-wire cords with three-prong plugs and outlets. DO NOT use extension cords
more than 50 feet (15 m) long.
PLEASE NOTE: FOR NORTH AMERICA ONLY
revised 1/11

4 - FORM NO. 56380890
1
3
4
5
6
7
8
11
9
10
13
12
2
14
KNOW YOUR MACHINE DESCRIPTIONS
Operator Handle (1): Operator holds onto this handle to move the machine from one location to another.
Solution Tank Lid (2): This lid screws off so the tank can be filled. The solution fill hose is tethered to the lid, and hangs inside the arm
of the Operator Handle.
Recovery Tank Lid (3): This lid covers the opening in the Recovery Tank. This is where the operator can access the tank to clean
it and the ball float cage. The tank can be flushed out by running clean warm water into this opening and laying the open drain
hose into a bucket or drain.
Recovery Hose (4): Waste water is picked-up through this hose.
Spray Hose (5): This hose delivers water from the machine to the cleaning tool.
Drain Hose (6): This hose is used to empty the recovery tank. NOTE: hold the end of the hose above the water level in the tank
to avoid sudden, uncontrolled flow of waste water when you remove the cap, then lower the hose slowly to control the rate of
discharge.
Quick Disconnect (7): Point of attachment for the Spray Hose (5).
Tools & Accessories (8): Various accessories can be stored on the machine.
Castors and Wheels (9): Castors pivot for ease of steering, and large back wheels make it easy to roll the machine from location
to location.
Recovery Hose Inlet (10): Point of attachment for the Recovery Hose (4).
Chemical Feed Lines (11): These clear tubes connect the cleaning chemical containers to the machine where the chemical can
be siphoned into the outlet water from the pump. Metering tips -- used to change the ratio of water to chemical -- are installed
here.
Switch Plate (12): The machine’s on/off switches for the vacuum and for the pump are located here and this is where the valve to
change chemical feeds is located.
Power Cord (13): The 25 ft. power cord connects to a power cord pigtail on the rear of the machine.
Chemical Container Holders (14): Two molded-in bottle holders for chemical jugs.

FORM NO. 56380890 -5
O
I
O
12
3
4
METERING TIPS
COLOR HOLE SIZE MIX RATIO FLOW RATE
Orange 0.007 1 oz : 128 oz 1.0 oz/gal
Pink 0.012 1 oz : 64 oz 2.5 oz/gal
Dark Green 0.014 1 oz : 50 oz 3.0 oz/gal
Yellow 0.016 1 oz : 32 oz 5.0 oz/gal
Light Blue 0.020 1 oz : 20 oz 6.0 oz/gal
Burgundy 0.022 1 oz : 15 oz 9.0 oz/gal
Black 0.048 1 oz : 5 oz 20 oz/gal
KNOW YOUR SWITCH PLATE
Vacuum Switch (1): turns on the vacuum motor.
Chemical Valve (2): switches between the two chemical containers. When the selector is pointed straight down, the valve is off and
neither chemical is selected. When the selector is pointed directly towards one or the other symbols, that chemical is selected.
Solution Pump Switch (3): turns on the solution pump.
Quick Connect (4): this is where solution comes out of the machine and the attachment point for the solution hose.
METERING TIPS
The chemical metering tips allow you to select the ratio of chemical to water, as the water flows out of the machine. Insert the correct
metering tip for the desired mixture into the chemical siphon tube.

6 - FORM NO. 56380890
OPERATION
1) Insert the appropriate metering tips into the chemical feed lines (see illustration, page 5).
2) Fill the holding tank with warm water (not exceeding 120 °F). Do not add any chemical to the tank.
3) Prepare the area for cleaning by emptying waste receptacles, clearing debris, removing paper products, blowing out vents, and
sweeping floors.
4) Connect the 25 ft power cord to the pig-tail on the rear of the machine. Test the GFCI on the power cord before each use. Plug the
GFCI protected power cord into an outlet.
5) PRIME THE PUMP: Attach the priming hose to the outlet quick disconnect and place the open end of the hose into the recovery
tank. Turn on the pump and let it run until the pump is completely primed (no visible air in the water stream). Turn the pump off.
NOTE: prime the machine before you place the chemical feed tubes into chemical containers.
6) Disconnect the priming hose and attach the solution hose to the quick disconnect.
7) Attach the spray gun to the other end of the solution line.
8) Place chemicals in the molded-in chemical bottle containers on the rear of the machine. Insert one of the feed lines into one of the
chemical containers. Secure the line by screwing on the cap. The chemical will feed from which ever container the selector valve on
the switch plate is turned towards and when the gun is used in the low pressure setting. Use chemicals with a pH of between 4 and
12. Never add chemicals to the clean water tank.
9) Set the spray gun to low pressure by sliding the pressure selector forward (low pressure = forward; high pressure = back).
10) Turn on the pump switch (push button) and spray through the gun for a few seconds to fill the line with solution.
11) Apply the chemical to the walls and fixtures from the bottom up. Spray the floor last as you work your way out of the room.
12) Allow the chemical to work for the proper amount of dwell time, according to the chemical manufacturer’s directions. Agitate heavily
soiled areas with a scrub brush.
13) Turn off the chemical injector valve by turning the selector to the down position.
14) Set the spray gun to high pressure and rinse the area from the top down.
15) Connect the vacuum hose, attach the squeegee, and turn on the vacuum (rocker switch).
16) Squeegee off the mirrors, pick up the liquid off the floor with the floor tool. If you have the optional blow dry hose, use it to dry the
fixtures.
17) Drain the recovered water into a utility sink or toilet. NOTE: Keep the top of the drain hose higher than the water level in the tank to
avoid uncontrolled discharge of water when you open the cap on the hose.
CAUTION
To avoid vacuum motor damage, always use a defoamer any time foam is present.
Before you turn on the vacuum always make sure the filter screen on the ball float is clean and that the ball can travel freely.
RE-PRIMING THE PUMP
If the pump looses prime between jobs, follow the instructions to PRIME THE PUMP, above. If that doesn’t get water flowing, put the
priming hose into the vacuum inlet hose barb and cover the rest of the space around the priming hose with your hand. Turn on the
vacuum (with the pump also running) and let the suction of the vacuum assist in getting water into the pump.

FORM NO. 56380890 -7
MAINTENANCE
1) Use only approved chemicals at the recommended mix ratios. All chemicals should be added through the feed system and NOT
added directly to the water in the solution tank to prevent possible damage to the pump, seals, or other components.
2) For optimum performance, flush the Chemical Feed lines after every job by replacing the chemical containers with containers of
clear water and spraying through the gun until the fluid stream is clear. See the Maintenance Schedule, below.
3) The pump seals and/or valves in the high pressure pumps may need to be replaced after about 1000 hours of use, if the pump
begins to loose performance or to leak. The pressure regulator valve may need to be when a drop in the spraying pressure at the
tool is apparent.
4) If the 4”, clear lid is removed from the top of the base (solution tank), you will need to apply a silicone sealant to the threads when
you reinstall the lid to seal for vacuum leaks.
MAINTENANCE SCHEDULE
ITEM DAILY WEEKLY QUARTELY YEARLY
Flush chemical lines X
Check/clean vac inlet filter X
Clean solution filter X
Check vacuum motor airways X
Check pump for leaks X
Check vacuum motor brushes* X
* Have Advance check the carbon brushes once a year or after about 500 hours of operation.
TECHNICAL SPECIFICATIONS (as installed and tested on the unit)
MODEL 56380772 56381594
VACUUM MOTOR: 2 stage, 8 amp 2 stage, 8 amp
WATER LIFT: 97” 97”
AIR FLOW: 100 CFM 100 CFM
TANK CONSTRUCTION: Rotationally molded polyethylene Rotationally molded polyethylene
SOLUTION TANK CAPACITY: 20 gallon 20 gallon
RECOVERY TANK CAPACITY: 12 gallon 12 gallon
APPLICATION FLOW: 200 psi 400 psi
VAC & SOLUTION HOSE LENGTH: 15 feet 15 feet
POWER CORD: 25 feet 25 feet
HEIGHT: 38.5 inches 38.5 inches
WIDTH: 21.25 inches 21.25 inches
LENGTH: 34 inches 34 inches
WEIGHT 85 LBS 85 LBS
revised 10/10

8 - FORM NO. 56380890
OI
O
12
4
5
6
10
16
11 12 13
15
21
14
24
22 23
25
17
9
20
3
26
19
87
23B
3B
18
16
15
17
26
400 PSI
200 PSI
revised 10/10

FORM NO. 56380890 -9
Item Ref. No. Qty Description
1 56380775 1 Lid and gasket, recovery tank
[ ] 1 Lid 12 X 12 Ester Coplyester
[ ] 1 Screw 6-32 X 1/2 Panhead
[ ] 1 Nut Nylon Lock 6/32 Z.P.
[ ] 1 Chain 8 W/ D Couplings Both E
[ ] 2.875 Gasketseal Black Neoprene 8
2 56380780 1 Hose kit, drain, priming and vac inlet
[ ] 1 Plug Drain Hose1 1/2 Dia Gre
[ ] 1 Hose Drain 1- 1/2 Dia X 24
[ ] 1 Hose Clamp 3/4 X 1 3/4 Ss
[ ] 1 Hose Vacuum Clear 1-1/2 X
[ ] 1 Hose Barb Fitting Black Abs
[ ] 1 Syphon/Priming Hose For 300 An
[ ] 1 Clamp Hose Plastic Dump Hose
3 56380782 1 Tubing kit, water and chemical feed
[ ] 20 Hose 3/8 Id 0.688 Od Red
[ ] 126” Tubing Clear 1/4 Idx 3/8 Od
[ ] 2 Chemical Feed Cap & Tube W/Ff
[ ] 2 Reducer 3/8 Pipe Female To 1
[ ] 1 Injector Chemical Brass 4500
[ ] 1 Hose Barb Solution Tank Standa
3B 56380913 1 Chemical metering injector and tips
[ ] 2 Metering Tip Black 0.048 Orif
[ ] 2 Metering Tip Burgundy 0.022 O
[ ] 2 Metering Tip Light Blue 0.020
[ ] 2 Metering Tip Yellow 0.016 Ori
[ ] 2 Metering Tip Dark Green 0.014
[ ] 2 Metering Tip Pink 0.012 Orifi
[ ] 2 Metering Tip Orange 0.007 Ori
[ ] 1 Injector Chemical Brass 4500
4 56380774 1 Power cord, 25 ft, with GFCI
5 56380783 1 Power cord pigtail with cord retainer
6 56380781 1 Vacuum motor kit, with gasket and hose
[ ] 1 Sleeve Vacuum Outlet For Hos
[ ] 2 Electrical Connec .250 X .032
[ ] 1 Vacuum Motor 120 Volts 2-Sta
[ ] 1 Gasket 1 Side Adhesive 5-1/2 O
[ ] 4 Hose 2 Id 50 Lenght Rb
7 56380785 1 Tank, Recovery, complete
[ ] 1 Vacuum Tank Orca 8 Gal Grey
[ ] 2 Hose Barb Fitting Black Abs
[ ] 1 Spin Weld Boss 1- 3/16
[ ] 1 Plug Drain Hose1 1/2 Dia Gre
[ ] 1 Hose Drain 1- 1/2 Dia X 24
[ ] 1 Hose Clamp 3/4 X 1 3/4 Ss
[ ] 1 Clamp Hose Plastic Dump Hose
[ ] 1 Elbow 90 Degree Abs 1-1/2 S
[ ] 1 Adapter Abs 1-1/2 Trap Sl
[ ] 1 Elbow 90 Pvc 1-1/2 Slip X F
[ ] 1 Filter S/S Ball Float With Rig
[ ] 1 Adapter Female 1 1/2
8 56380779 1 Vacuum inlet kit
[ ] 1 Filter S/S Ball Float With Rig
[ ] 1 Elbow 90 Degree Abs 1-1/2 S
[ ] 1 Adapter Abs 1-1/2 Trap Sl
[ ] 1 Adapter Female 1 1/2
[ ] 2 Hose Barb Fitting Black Abs
[ ] 1 Elbow 90 Pvc 1-1/2 Slip X F
9 56380786 1 Switch Plate Complete (200 psi)
[ ] 1 Switch On-Off Illuminated Cle
[ ] 1 Switch Plate For The All Clea
[ ] 1 Switch Rocker Dpst W/Light 120
[ ] 1 Valve 3-Way For Spotter & Apc
[ ] 2 Hose Barb 90 Deg Nylon 1/8 Mpt
9 56380919 1 Switch Plate Complete (400 psi)
[ ] 1 Switch On-Off Illuminated Cle
[ ] 1 Switch Plate For The All Clea
[ ] 2 Hose Barb 90 Deg Nylon 1/8 Mpt
[ ] 1 Valve 3-Way For Spotter & Apc
[ ] 16” Seal Neoprene 5/8 Gap X 1-1
[ ] 7 Washer Backup For 1/8 Rivet
[ ] 7 Rivet 1/8 Dia Aluminum 1/8 T
[ ] 14 Bracket Hepa Filter Retaining
[ ] 1 Switch Rocker Dpst On/Off 20
10 56380847 1 Switch Kit (200 psi)
[ ] 1 Switch On-Off Illuminated Cle
[ ] 1 Switch Rocker Dpst W/Light 120
[ ] 1 Valve 3-Way For Spotter & Apc
[ ] 2 Hose Barb 90 Deg Nylon 1/8 Mpt
[ ] 8 Screw 6 X 1/2 S.M.S. S/S
10 56380939 1 Switch Kit (400 psi)
[ ] 2 Hose Barb 90 Deg Nylon 1/8 Mpt
[ ] 1 Switch On-Off Illuminated Cle
[ ] 1 Switch Rocker Dpst On/Off 20
[ ] 1 Valve 3-Way For Spotter & Apc
[ ] 1 Instruction Sheet
11 1 Pallet, component mounting, empty *
Item Ref. No. Qty Description
12 1 Lid, with fill hose, holding tank/base
[ ] 1 Elect Butt Conn 10-12 Ga Non-I
[ ] 1 Hose Fill Apc
[ ] 1 Adapter Faucet Inside/Outsid
[ ] 1 Tie Wire 8 W/Mounting Hole
[ ] 1 Chain 8 W/ D Couplings Both E
[ ] 1 Tie Wire 8 W/Mounting Hole
[ ] 1 Cap-Raw With Tether
13 56380843 1 Fasteners kit
[ ] 2 Hinge Pin 1/4 X 2.25 S/S
[ ] 1 Clip Handle Black Vinyl Coated
[ ] 1 Strap/Buckle Cord Wrap W/Spur
[ ] 1 Bolt 8-32 X 1/2 Pan Head
[ ] 3 Washer Internal Tooth 10
[ ] 2 Hose Clamp 3/4 I.D. For Hhp
[ ] 1 Wire Hanger 3/16 S/S 8 Gall
[ ] 2 Cap Black .165 I.D. X 27/16 I
[ ] 2 Cap .281 I.D. X 1/2 Long In B
[ ] 2 Screw Thumb 1/4-20 X 1 Type
[ ] 2 Washer 1/4 I.D. 1 O.D. F
14 56380841 1 Lid and ring, 4”
[ ] 1 Lid And Ring 4 Lid Clear
[ ] 6 Screw 8-32 X 7/8 Panhead Phi
[ ] 6 Nut Nylon Lock 8-32 Stainles
[ ] 1 Chain 8 W/ D Couplings Both E
[ ] 1 Gasket For Apc Closed Cell B
15 56380789 1 Kit-Pump and Motor (200 psi)
[ ] 1 Pump & Motor 200 Psi 120v.
[ ] 8” Tubing Black 3/4 Id X 1
[ ] 1 Elbow 90 Deg 1/4 Fpt X 1/4 F
[ ] 1 Hose Barb With Male 1/4 Pipe X
[ ] 4 Hose Clamp 3/8-7/8
[ ] 2 Electrical Connec .250 X .032
15 56380923 1 Kit-Pump and Motor (400 psi)
[ ] 1 Pump Piston Style 300-500 Ps
[ ] 1 Motor A/C 1/3 Hp For 300 Psi P
[ ] 1 Bearing & Cam Assembly Size 1
16 56380791 1 Motor-Pump Drive (200 psi)
2060 1 Motor-Pump Drive (400 psi)
17 56380790 1 Pump Complete (200 psi)
[ ] 1 Pump Head 114v Buna U-Valve
[ ] 4” Tubing Black 3/4 Id X 1
[ ] 1 Elbow 90 Deg 1/4 Fpt X 1/4 F
[ ] 1 Hose Barb With Male 1/4 Pipe X
[ ] 4 Hose Clamp 3/8-7/8
[ ]#1 Bearing & Cam Assembly
17 56380902 1 Pump Complete (400 psi)
[ ] 1 Hose Assy Mpt X Fm Swivel Ove
[ ] 1 Hose Barb 1/2 Hose To 3/8 M
[ ] 1 Flare Fitting Fm 90 Deg -6 X
[ ] 1 Quick Connect Plug Brass 1/
[ ] 1 Coupling 3/8 X 3/8 Brass
[ ] 1 Quick Connect Brass 1/4 Fpt
[ ] 1 Reducer 3/8 Pipe Female To 1
[ ] 1 Plug Brass Pipe 1/4 Pipe H
[ ] 4 Capscrew 1/4-20 X 2 X 1
[ ] 4 Washer Rubber 1/4 Id X 3/4
[ ] 8 Washer Flat 3/16 Zinc Plat
[ ] 4 Bolt Hex 1/4-20 X 1 Full
[ ] 12.75” Hose 1/2 Id 2 Braid 250 Psi Go
[ ] 6 Hose Clamp 3/8-7/8
[ ] 1 Hose Barb 1/4 Pipe X 1/2 Hose.
[ ] 1 Injector Chemical Brass 4500
[ ] 1 Bearing & Cam Assembly Size 1
[ ] 1 Pump Piston Style 300-500 Ps
18 56380788 1 Filter, pump in-line, with hoses
[ ] 2 Hose Clamp 3/8-7/8
[ ] 11” Hose 1/2 Id Wire Reinforced
[ ] 1 Filter Water In-Line
[ ] 8.75” Hose 1/2 Id 2 Braid 250 Psi Go
19 56380879 1 Vacuum Hose 15 ft Complete
20 56380787 1 Quick disconnect kit, with washers
[ ] 1 Quick Disconnect Plug Male
[ ] 2 Washer Brass Half Hard 1 X
[ ] 2 Washer 1 Od X 9/16 Id X
21 56380851 1 Grommets and foam
[ ] 1 Foam Reticulated 20 Ppi 1/2 X
[ ] 1 Grommet 3/4 Id X 3/16 Panel
[ ] 1 Grommet 11/16 Id X 1/4 Pane
22 56380797 1 Cap, drain, and brass fitting
[ ] 1 Adapter Brass 3/4 Hose Male
[ ] 1 Cap Garden Hose 3/4 Fght N
revised 1/11
Item Ref. No. Qty Description
23 56380798 1 Castor kit
[ ] 2 Caster Swivel 4 Gray Non Ma
[ ] 8 Washer Flat 3/16 Zinc Plat
[ ] 8 Screw 1/4-20 X 5/8 Hesx Co
[ ] 2 Plug Square Tube Smooth 3/4
[ ] 1 Caster Plate For The Orca With
23B 56380904 1 Castor plate, with plugs
[ ] 2 Plug Square Tube Smooth 3/4
[ ] 1 Caster Plate For The Orca With
24 56380795 1 Holding tank/base
[ ] 2 Plug Square Tube Smooth 3/4
[ ] 1 Base For Apc/Orca Dark Gray
[ ] 1 Caster Plate For The Orca With
25 56380799 1 Wheel kit
[ ] 2 Wheel 10 Grey Plastic Insert
[ ] 2 Axel Cap Black Pal Nut
[ ] 1 Axel Rod Zinc Plated 1/2 Ro
26 56380893 1 Pressure Regulator (200 psi)
945D 1 Unloader Valve (400 psi)
MISCELLANEOUS PARTS
[ ] 56380844 1 Labels Kit All Cleaner
[ ] 1 Label N/A & Kent Warning 6 Lo
[ ] 2 Label All Cleaner 6 X 3 Ov
[ ] 56380867 1 Pallet Kit Component Mounting
[ ] = Not Shown
#= Revised or new since last update

10 - FORM NO. 56380890
1
24
5
6
7
8
3
9
10
3
4
5
TOOLS
OPTIONAL ACCESSORIES
1 56380856 Mop frame
2 56380857 Mop, microfiber, package of six
3 56380888 Squeegee assembly, 24”
4 56209089 Squeegee assembly, 30”
5 56380871 Mount assembly, mechanical, for squeegee head
6 56380877 Blower hose assembly, with nozzle
7 56380805 Recovery hose, 25 ft
8 56380838 Solution hose, 25 ft
9 56380865 Bucket, 10 qt
Tool Kit, standard, complete -- 56380846 (200PSI) / 56381618 (400PSI)
1
2
7
6
8
1 56108017 Squeegee, hand-held, 12”
2 56380853 Handle, 12”, for hand squeegee
3 56380804 Pressure Line 15 Ft Complete (200 psi)
56381617 Hose Assy-1/4 X 15 Blue (400 psi)
4 56380855 Brush, dual surface, polypropylene
5 56108027 Wand, two-piece, snap fit
6 56108028 Squeegee,14’, for floor
7 56108072 Spray gun, complete
8 56380802 Metering tip kit, two each of seven sizes
9 SUBSYP1 Priming hose assembly, for 200 psi pump
10 56380852 Handle, black, 54”
9
revised 1/11

FORM NO. 56380890 -11
BUT BEFORE PAINTING.
C
1. ALL DIMENSIONS IN INCHES.
APPROVED
APPROVED
DRAWN
SIZE
AS NOTED.
CODE
APPROVED
UNITS IN [ ] ARE ISO METRIC
NOTES UNLESS OTHERWISE
SPECIFIED
4. REMOVE ALL BURRS AND SHARP
CHECKED
EDGES.
ORCAD
PROJ ENG
DIM. IN [ ] ARE MM.
2. DO NOT SCALE DRAWING.
TITLE
3. ALL DIMENSIONS APPLY AFTER
PLATING AND HEAT TREATING,
DI
A
POWER CORD
P/N 1120 P/N 1120
P/N 1120 P/N 1120
P/N 1120 P/N 1120
P/N 1120P/N 1120
11
11
0
0
00
PMO
12-14-10
12-14-10 SAB
WGL
WGL
12-14-10
12-14-10
1. NON-CSA MACHINE
2. VAC SWITCH
ALL CLEANER - P/N 2123
ALL CLEANER XP AND TFC 400 - P/N 1644
3. PUMPS
ALL CLEANER - P/N 960
ALL CLEANER AND TFC 400 - P/N 2060(120V)
APC 328(400PSI) - P/N 2064-CE
4. VAC
ALL CLEANER - P/N 408
ALL CLEANER XP AND TFC 400 - P/N 408
APC 328(400PSI) - P/N 407A
ALL CLEANER XP AND TFC 400 - P/N 2060(120V)
0
00
0
00
00
4" OF HEAT SHRINK
P/N 1649
GRN
BLK
WHT WHT 14 AWG 14.5"
BLK 14 AWG 14.5"
BLK 14 AWG 4.5"
BLK 14 AWG 3.5"
WHT 14 AWG 4.5"
WHT 14 AWG 4.5"
BLK 14 AWG 14"
WHT 14 AWG 14"
BLK 14 AWG 21"
WHT 14 AWG 21" GRN 14 AWG 20"
GRN 14 AWG 7"
GRN
M
~
PUMPP/N's SEE NOTE 3
M
~
PUMPP/N's SEE NOTE 3
P/N 170P/N 170
12
P/N 61P/N 61
1
2
P/N 1121P/N 1121
P/N 65
PANEL GROUND
P/N 65
PANEL GROUND
P/N 1121P/N 1121
P/N 61P/N 61 1
2
P/N 61P/N 61
1
2
P/N 1121P/N 1121
P/N 1120P/N 1120
M
~
VAC 1
P/N's SEE NOTE 4
M
~
VAC 1
P/N's SEE NOTE 4
1 2
P/N 170P/N 170
12
P/N 1121P/N 1121
P/N 1120P/N 1120
P/N 64P/N 64
P/N 1120P/N 1120
P/N 1623R
PUMP
P/N 1623R
PUMP
1 2
3 4
P/N 1120P/N 1120
P/N SEE NOTE 2
VAC
P/N SEE NOTE 2
VAC
1 4
2 5
revised 1/11
WIRING DIAGRAM

14600 21st Avenue North
Plymouth, MN 55447-3408
www.advance-us.com
Phone: [phone]
Fax: [phone]
©2011 Nilfisk-Advance, Inc.
A Nilfisk-Advance Brand