Advanced Elements AdvancedFrame AE1007-E User manual

IMPORTANT!
PLEASE READ THIS MANUAL CAREFULLY BEFORE PROCEEDING. AFTER READING
THIS MANUAL, SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
AdvancedFrame
Convertible Elite
Inflatable Kayak
Owner’s Manual
MODEL AE1007-E
1 OR 2 PERSON KAYAK
ADVANCED ELEMENTS, INC. 2019 REV 06-2020
PATENTED

3
TABLE OF CONTENTS
1. Caution/Safety .................................................................. 4
1.1 Boating Safety........................................................ 5
2. Specification...................................................................... 6
2.1 Capacity ................................................................. 6
2.2 Features .................................................................. 6
3. Assembly/Inflating/Deflation Instruction .................... 7
3.1 Assembly ............................................................... 7
3.2 Understanding Your Valves................................ 8
3.3 Inflating................................................................ 10
3.4 Over Inflation ...................................................... 11
3.5 Deflation............................................................... 12
3.6 Folding ................................................................. 12
4. Guidelines for Usage ..................................................... 13
5. Proper Care and Storage ............................................... 13
6. Repairs ............................................................................. 14
6.1 Repairing Small Punctures and Cuts............... 14
6.2 Repairing Pinholes ............................................. 14
7. Troubleshooting............................................................. 14
8. Statement of Origin ....................................................... 17
9. Declaration of Conformity ........................................... 18
10. Warranty and Registration........................................... 19

TM
4
1. CAUTION - SAFETY WARNING
Users of this product agree by their use to accept the inherent risks involved in this paddlesports
activity and agree to follow all instructions, cautions, and warnings carefully before using this
Kayak.
(PLEASE READ CAUTION STATEMENT CAREFULLY)
SAFETY WARNING
PADDLESPORTS CAN BE VERY DANGEROUS AND PHYSICALLY DEMAND-
ING. THE USER OF THIS PRODUCT SHOULD UNDERSTAND THAT PARTICI-
PATION IN PADDLESPORTS MAY INVOLVE SERIOUS INJURY OR DEATH.
OBSERVE THE FOLLOWING SAFETY STANDARDS WHENEVER USING THIS
PRODUCT.
· GET PADDLESPORTS INSTRUCTIONS SPECIFIC TO THIS TYPE OF CRAFT.
· OBTAIN CERTIFIED FIRST AID TRAINING AND CARRY FIRST AID AND
RESCUE/SAFETY EQUIPMENT.
· ALWAYS WEAR A NATIONALLY APPROVED PERSONAL FLOTATION DEVICE.
· ALWAYS WEAR A HELMET WHERE APPROPRIATE.
· DRESS APPROPRIATELY FOR WEATHER CONDITIONS; COLD WATER AND/OR COLD
WEATHER CAN RESULT IN HYPOTHERMIA. CHECK YOUR EQUIPMENT PRIOR TO
EACH USE FOR SIGNS OF WEAR OR FAILURE.
· NEVER PADDLE ALONE.
· DO NOT PADDLE IN FLOOD CONDITIONS.
· BE AWARE OF APPROPRIATE RIVER WATER LEVELS, TIDAL CHANGES, DANGEROUS
CURRENTS, WEATHER CHANGES, AND STRONG OFF SHORE WINDS.
· SCOUT UNFAMILIAR WATER; PORTAGE WHERE APPROPRIATE.
· DO NOT EXCEED YOUR PADDLING ABILITY; BE HONEST WITH YOURSELF.
· CONSULT YOUR PHYSICIAN PRIOR TO BEGINNING YOUR PADDLESPORTS TRAINING.
· YOU MUST NOT USE ALCOHOL OR MIND ALTERING DRUGS PRIOR TO USING THIS
PRODUCT.
· FOLLOW THE MANUFACTURER’S RECOMMENDATIONS FOR THE USE OF THIS
PRODUCT.
· IF ADDITIONAL OUTFITTING IS REQUIRED, USE MANUFACTURER’S APPROVED
MATERIALS ONLY; DO NOT IMPAIR ENTRY OR EXIT ACCESS.
· READ OWNER’S INFORMATION PACKET PRIOR TO USING THIS PRODUCT.
THE USER OF THIS PRODUCT ACKNOWLEDGES BOTH AN UNDERSTANDING AND AN
ASSUMPTION OF THE RISK INVOLVED IN PADDLESPORTS.
CAUTION
ADVANCED ELEMENTS, INC.
TOLL FREE 866-262-9076
Please read this entire manual for additional safety information. Please pay close aention to items
marked DANGER, WARNING, CAUTION, IMPORTANT, NOTICE, NEVER and ALWAYS.

5
1.1 Boating Safety
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that follow this symbol to avoid possible injury or
death.
DANGER
Indicates an imminently hazardous
situation which, if not avoided, will
result in death or serious injury or
substantial property damage.
WARNING
Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury or
property damage.
CAUTION
Indicates a potentially hazardous
situation which, if not avoided, may
result in property damage.
CAUTION
Used without the safety alert symbol
indicates a potentially hazardous
situation, which, if not avoided, may
result in property damage.
NOTICE
Indicates installation, operation or
maintenance information which is
important but not hazard-related.
e. If a procedure,
decision. REMEMBER - always use common sense when paddling YOUR KAYAK!
®

6
2. SPECIFICATION
Dimensions:
Length: 15’
Width: 32”
Weight: 52 lbs (23.5 kg)
Max. Person Capacity: 500 lbs (227 kg)
Max. Persons & Gear Capacity: 550 lbs (249 kg)
Recommended Pressure:
Main chambers: 2.0 psi (0.14 bar)
Floor chamber: 6.0 psi (0.41 bar)
2.1 Capacity
The person/load capacity is determined by the availability of proper seating on the kayak.
Acceptable seating determines the number of passengers, not the overall load capacity.
MAXIMUM CAPACITIES
550 LBS PERSON, GEAR
PRESSURE = 2.0 psi (main chambers)
MANUFACTURER: ADVANCED ELEMENTS, INC. CONCORD, CA USA 94524
MODEL AE1007 - ADVANCEDFRAME™ CONVERTIBLE KAYAK
COMPLIANCE
WITH
ISO 6185-1
TYPE III, A
0123
2+= 249 kg
0,14 bar (main chambers)
2PERSON OR 500 LBS.
THIS BOAT COMPLIES WITH NMMASTANDARDS OF EFFECT
ON THE DATE OF CERTIFICATION
NATIONAL MARINE MANUFACTURES ASSN.
2010
NOT INTENDED FOR MECHANICAL PROPULSION
AdvancedFrame®Convertible Kayak Capacity Label
WARNING:
Overloading will reduce freeboard and increase the likelihood of swamping, especially in heavy
2.2 Features
SPECIAL FEATURES:
Hull Design
Durable: 3 Layers of material for extreme puncture resistance.
Easy to Set Up
Comfortable: High support, adjustable padded seat provides comfort for hours of paddling.
Versatile: 3 Seat locations allow for paddling solo or tandem.

7
OPTIONAL DECKS:
ak
with the option for using a spray skirt. Three seating positions allow for maximum versatility.
Single Double
3. ASSEMBLY/INFLATING/DEFLATION INSTRUCTION
The AdvancedFrame®Kayak has a rigid frame in the bow and stern that enhances its performance.
3.1 Assembly
The illustration below shows the general assembly of the kayak. Your kayak comes from the
INFLATABLE FLOOR
ADVANCEDFRAME
OUTER COVER
BOW RIB STERN RIB
Step 1
Step 2
Step 3
Step 1
Advanced Elements
Spring Valve
Drop-Stitch Floor
High-back
Lumbar Seat
®

8
1. Your AdvancedFrame®kayak comes from the factory pre-assembled however should you
take it apart you will need to insert the aluminum Bow Rib and the Stern Rib into the
webbing
2. Place the AdvancedFrame®(with Ribs installed), into the Outer Skin, making sure that the
air valve is upright and at the back of the boat, and lined up with the opening on the outer
cover.
3.
inside the center of the AdvancedFrame®with twist valve up.
4.
5. NOTE
This will allow the zippers to align properly.
3.2 Understanding Your Valves
Advanced Elements AdvancedFrame®Convertible kayak uses the following valves. The
Advanced Elements spring valve has the function and durability of other military type valves
and is compatible with most standard pumps. The lock nut holds the valve in place with the
threading.
The valve’s plunger stem should be set in the down/inward position recessed in the
valve threading.
.
How the Spring Valve Works:
spring-loaded plunger open, allowing air to enter the air chamber
the valve’s plunger stem will be inside, or lower than, the rim of the valve. To change the valve
stem down/inward, and give it a 1/4 turn. This will lock the plunger open and allow the air to
rush out. Use the same procedure in reverse to unlock the valve plunger, allowing it to spring up
Special Note:
inward) position because these types of pumps typically do not provide enough air pressure
®
®
®

9
the job.
Using the “Screw-on” Spring Valve Adaptor:
The screw-on Spring Valve Adaptor was designed to enable the pump hose to securely connect to
The valve adaptor also has a semi-circle protrusion that depresses the valve stem, opening the
Special Note: The Spring Valve Adaptor comes with all current Advanced Elements pumps,
OPERATING THE “TWIST” VALVES
TWIST TO OPEN / INFLATE / THEN CLOSE
TWIST VALVE
PUMP HOSE
INSERT
1
2
Bellows Foot Pump or a Double Action Hand
Pump. Never use compressors, CO2 or compressed air as they may damage your kayak.
®
Valve Stem Closeup Spring Valve Top View

10
ADVANCEDFRAME AIR CHAMBER DESIGN
®
Main Chamber 1
Main Chamber
Dividing Wall
Main Chamber 2
Floor Chamber 3
3.3 Inflation and Setup in 3 Simple Stages
1. Starting with Main Chamber 1, check to be sure that the valve plunger is UP or in the
INFLATE position (See Figure 1 on previous page).
NOTE:This will bea minimalamount ofair pressure. DO NOT inflate this chamber to 2.0 psi!
DO NOT PUT ALL OF THE AIR PRESSURE IN THIS CHAMBER.
3. Inflation of Main Chamber 1 is complete. Secure the black cap on the valve and proceed to
Main Chamber 2. Continued on Next Page.
Inflating Main Chamber 1: For the best setup experience, we recommend
STAGE 1
using the AE2011 Double Action Hand Pump with Gauge which provides 4,000 cc’s
per full cycle stroke.
As shown in the diagram above, our unique tube design divides the main inflation
chamber into two separate air chambers that encircle the entire kayak. This provides
optimum safety when out on the water. Following the inflation steps below will
ensure that you have properly divided the air into the two main chambers, not only
for proper performance, but for safety as well.
2. Using the AE2011 Double Action hand pump, inflate the kayak approximately 55 full (up then
down) strokes until the kayak begins to take shape. If using another pump, the key here is to
just partially inflate the kayak. The kayak will still be soft/under-inflated.

11
Figure 3. Plastic Bow and Stern Insert
INFLATION TIPS
NEVER USE COMPRESSORS,
CO2, OR COMPRESSED AIR AS THEY MAY DAMAGE YOUR KAYAK. The main chambers use
high-end military style, plunger valves (Push in and twist to activate the spring-loaded check
valve for inflating, or push-in and twist to lock open for deflating).
3.4
CAUTION:
weather and water your kayak will lose some pressure. If this occurs, you may want to add a
bit more air to the kayak to improve performance. In hot weather or prolonged sunlight, the air
inside the kayak will expand. You must let some air out of the appropriate chambers to prevent
the kayak from failing due to overpressure. You should avoid exposing your kayak to extreme
temperatures (hot or cold).
Inflating The Floor and Smaller Air Chambers:
STAGE 3
Over Inflation and Temperature Regulation:
1. Moving to Main Chamber 2 on the inside of kayak, check to be sure that the valve plunger is
UP or in the INFLATE position (See Figure 1) and inflate until firm to touch (2.0 psi ONLY).
2. Inflation of Main Chamber 2 is complete. Secure the black cap on the valve.
Inflating Main Chamber 2:
STAGE 2
®
1. Inflate Chamber 3 “floor” using the adaptor included in the Repair Kit. (4.0 psi - 6.0 psi MAX)
2. Inflate chamber 4 (thwart/foot brace) until firm. (1.0 psi ONLY). Aach to Velcro on side
tubes when paddling tandem. Remove or move the thwart/foot brace when paddling solo.
3. Inflate chamber 5 & 6 for desired deck lift. (1.0 psi ONLY)
4. Make sure all valves are closed tightly and properly.
5. Finally, insert plastic Bow and Stern Forms into the grey pockets on the bow and stern of the
kayak. (See Figure 3).

12
2.
3. Fold in half, down the center.
4. Fold into 5 equal sections.
4.
3.5
, 2, & 3.1rebmahcmorfspacehtevomeR.1
2. (See Figure 1).
.6hguorht4srebmahcnosevlavtsiwtnepO.3
4.
3.6 Folding
NOTICE
1. Reversing
your pump to pump out all the remaining air will make folding easier.

13
Most areas have local laws and regulations about the use and equipment of small boats. Usually
a phone call to the local authorities will provide you with the needed information. Some areas
may require that you register and display a registration number on the front of your kayak.
Your kayak is designed to be paddled with a double bladed kayak paddle. Paddle with short
and even strokes. Keep the blade close to the kayak and the paddle almost vertical. Pull with
your lower hand and push with your upper hand. To reduce the amount of swaying at the
ALWAYS practice safety and take the time to learn about the area where you are paddling. Get
you do not over estimate your strength, your endurance or your skill. Be careful never to under
estimate weather conditions. Be aware of the dangers before you begin. Be aware of your skill
level. Be sure you understand and accept the risk of these dangers. There are many paddling
clubs all over the world. These can be a great source of information on places to paddle, people
to paddle with and most importantly, continued safety practices.
5. PROPER CARE AND STORAGE
use and care will increase the life of your kayak. Before storing your kayak, make sure it is both
CLEAN and DRY. You may clean your kayak with a mild soap and water. NEVER use strong
solvents to clean your kayak as they will destroy the material.
kept out of direct sunlight when stored. Avoid exposure to extreme temperatures (hot or cold).
If your boat is exposed to freezing temperatures while storing, allow it to warm up before
unfolding.
®
4. GUIDELINES FOR USAGE
Paddlesports can be very dangerous and physically demanding. The user of this product should
understand that participation in paddlesports may involve serious injury or death. Observe the
following safety standards whenever using this product. The user of this product acknowledges
both an understanding and an assumption of the risk involved in paddlesports.
for obvious signs of wear or failure. Review local rules and regulations and read again the
“CAUTION” statement.

14
5. If there is sand or gravel in the kayak, you can hose out the cover, and then wipe it
down with a towel.
6.
kayak absorbing most of the water, then pack it up.
PROBLEM
Does not hold air
The kayak is sagging
SOLUTION
The spring valve uses a plunger system. The only time the plunger
otate
counter-clockwise.
Be sure that the right pump is being used. You need a bellows foot
pump or a double action hand pump. A 12-V electric does not supply
-
7. TROUBLESHOOTING
Do not store your kayak for an extended period of time while wet.
Follow these steps for removing excess water.
1. Unzip the 2 zippers that run down the center of the kayak.
2.
from the outer cover. In order to completely separate these parts, it is necessary to
unscrew the locking nut on the spring valve.
3. Use a sponge or towel and wipe up any excess water in the outer cover.
4.
6. REPAIRS
6.1 Repairing Small Punctures and Cuts Using the Peel-And-Stick Patch
6.2 Repairing Pinholes
1.
you see air bubbles. Mark the location of the pinhole.
All kayaks come with a repair kit that includes a glueless peel-and-stick patch. For more significant
repairs, we include a selection of material patches that can be glued on. Simply aquire a PVC
glue at your local marine or outdoor store or contact our Customer Service for assistance via
email at [email protected] or 1-866-262-9076.
2. Deflate the tube and dry affected area. Following the instructions above, apply peel-and-stick
patach OR apply a drop of PVC glue to the pinhole.
3. If using glue, allow it to dry completely.
4. Do not inflate the kayak for at least 12 hours.
1. Cut a patch to size (approx. 1/2” larger than the hole or damaged area).
2. Carefully clean the area where patch will be placed with water and/or mild soap.
3. Make sure all surfaces are completely dry befor proceeding.
4. Carefully peel back the paper liner on the glueless patch and carefully apply the patch
over the hole-taking care to avoid any bubbles in the patch. Rub all edges to seal.
5. As a rule of thumb, the patch will start to cure immediately with approx. immediate
adhesion of 50% with full 100% adhesion 24 hours after application.

15
PROBLEM
Kayak still loses air.
Tube is kinked or
bent in.
Water in the kayak.
one side.
SOLUTION
If you have checked all the previous possible reasons for the kayak
losing air, then there may be a pinhole or a puncture somewhere on the
where a leak may be, take a clean rag with soapy water and begin rub-
bing the tube. If a hole is present, bubbles will continually form. Repair
using repair kit. If it is a very small pinhole, a dab of the glue may be
-
justing the position of the tube inside of the outer shell. The
-
proximately ten minutes. Fin will conform to its original shape. Even if
puddle up on the deck and leak through the zipper. Make sure that the
a spray skirt from our accessories list from a dealer. This will help keep
the inside of the kayak dry as well as you.
A kayak will always head in the direction of your last stroke. The longer
r is prop-
uneveness in the kayak.
®
The kayak will not hold
full pressure for more
than a couple of hours.
Make sure that the plunger is in the closed position. It should only
ck rubber

16
PADDLING NOTES:
It is alway a good idea to keep nots of your paddling experiences. Your notes can serve as a reminder
of what to look out for, as well as what gear to bring along, and what conditions are like.
DATE TIME LOCATION NOTES

Note: If your state requires the licensing of this boat, please use the form below. If you need any assistance filling
out this form, please contact Advanced Elements Customer Service Department.
MANUFACTURER’S STATEMENT OF ORIGIN
FOR A VESSEL SOLD IN THE STATE OF_____________________________________
The undersigned manufacturer hereby certies that the new boat described below, the property of
said manufacturer, has been transferred this _________day of _____________________, 20_________on
Invoice# _________________to:
Owner’s/Dealer’s Name_____________________________________________________________
Address___________________________________________________________________________
City, State, Zip______________________________________________________________________
Model Name Model Year Manufacturer’s Hull Identication#
m AdvancedFrame™ __________ HIN# _________________________
Convertible Kayak(AE1007)
Type: Kayak Hull Material: PVC/Polyester
Length Overall: 15’ Beam: 34”
U. S. Coast Guard Capacity Plate Information (where applicable):
Maximum persons capacity in whole persons: 500 lbs (227 kg)
Maximum weight capacity (persons & gear): 550 lbs (249 kg)
The manufacturer further certies that this was the rst transfer of such new boat and that all
information given herein is true and accurate to the best of their knowledge
TM
P.O. Box 5128 Concord, CA 94524
Signature_________________________________________________________________________________
FIRST ASSIGNMENT
FOR VALUE RECEIVED, in the amount of $ __________________________________________________,
the undersigned hereby transfers the Certicate of Origin and the boat described therein
to _______________________________________________________________________________________
Address __________________________________________________________________________________
and certies that the boat is new and has not been registered in this or any other state; Advanced
Elements, Inc. also warrants the title of said boat at time of delivery, subject only to the liens and
encumbrances as set out below:
Amount of Lien Date To whom Due Address
___________________ __________ __________________ ___________________________________
Dates___________________________ 20 _________, at _____________________ ____________________
___________________________ By:___________________________________________________________
Transferrer (Firm name) Sign Here ___________________________________________________________
Before me personally appeared _____________________________ who by me being duty sworn under
oath says the statements set forth above are true and correct. Subscribed and sworn to me before
this __________ day of _____________________________ 20 ___________.
___________________________________Notary Public Date commission expires_______________
(SEAL)

18
Declaration of Conformity
(according to ISO/IEC Guide 22 and EN 45014)
s’rerutcafunaM Name: Advanced Elements, Inc.
s’rerutcafunaM Address: P.O. Box 5128
Concord, CA 94524
,seralced that the product:
tcudorP Name: AdvancedFrame® Convertible Kayak
ledoM Number (s): AE1007
to which this declaration relates, meets the essential health and safety
stnemeriuqer and is in conformity with the relevant EU Directives listed below:
General Product Safety Directive
using the relevant section of the following EU standards and other normative
documents:
EN ISO 6185-1 : 2001
ABYC H-29: 2012
Date: January 1, 2019
Clay Haller, President
This product complies with European directives for recreational vessels as
published by the International Organization for Standardization (ISO).

19
LIMITED WARRANTY
OUR GUARANTEE
Advanced Elements, Inc. warrants this product to be free from defects in material or workmanship for a period of
one year from the date of purchase. Products that prove to be defective under conditions of normal and proper use
during the warranty period because of defective workmanship or faulty material will be replaced or repaired without
charge. For warranty service, contact Advanced Elements, Inc.
Advanced Elements, Inc shall inspect all warranty claims and in the event of a defect, repair or replace the defective
part or entire item, at its option. The purchaser must, before return of a defective product, obtain from Advanced
Elements, Inc, a return authorization number and return center address. Please write or call as listed below. Once an
authorization number is obtained, the purchaser must ship the product, POSTAGE PREPAID, to Advanced Elements,
Inc for repair. Do not ship to P.O. Box address as it may be sent back.
This warranty does NOT cover:
Products used for rental, for hire or in professionally guided tours and other uses not considered normal recreational
purposes; and punctures, cuts and abrasions sustained in normal use; and items involved in accidents; and items
damaged in white water mishaps, and other unreasonable uses or improper storage.
Advanced Elements, Inc shall within (30) days from receipt of an authorized return from purchaser, perform its re-
sponsibilities in conformance with this warranty.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION OF THE FACE HEREOF.
ADVANCED ELEMENTS SHALL NOT BE HELD LIABLE FOR INCIDENTAL AND CONSEQUENTIAL DAMAGES.
THIS WARRANTY IS INCLUSIVE IN LIEU OF ALL OTHER WARRANTIES.
This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
Advanced Elements, Inc.
P.O. Box 5128, Concord, CA 94524
Toll Free - 866-262-9076 - email [email protected] - www.advancedelements.com
It is very important to us that you are 100% satisfied with your Advanced Elements product. If you are not satisfied
for any reason at all please call us immediately Toll Free at 866-262-9076. Please use the Warranty Registration Form
at: www.advancedelements.com/warranty to register your Advanced Elements Product.