Advanced Elements AdvancedFrame AE1012 User manual

TM
IMPORTANT!
PLEASE READ THIS MANUAL CAREFULLY BEFORE PROCEEDING. AFTER READING
THIS MANUAL, SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
AdvancedFrame™
Inflatable Kayak
Owner’s Manual
MODEL AE1012
1 PERSON KAYAK
ADVANCED ELEMENTS, INC. 2011 REV 11-2010
PATENTED

It is our goal, at Advanced Elements, to develop new and unique paddles-
ports products that enhance our customers’ outdoor experience. Our focus is
on designing and manufacturing “Inatable kayaks with cuing edge tech-
nology”. Our kayaks incorporate many dierent materials and components
and deliver high performance at a very reasonable price. We are the makers
of the AdvancedFrame™ Inatable kayaks, Lagoon™ Inatable kayaks and
StraitEdge™ Canoe and Kayaks. The AdvancedFrame™ Kayaks are a hy-
brid of a folding frame kayak and an inatable kayak. Its bow slices through
water like a knife and rivals the tracking of hard-shell kayaks. The stern acts
as a skeg increasing the tracking performance. The Lagoon™ kayaks are
durable and lightweight. They have built-in rigid forms that increase the
performance once it is fully inated. You can take our inatables with you
anywhere in the world and no roof rack is needed! Keep it in the trunk of
your car and paddle whenever you want or pack it into a remote wilderness
area and paddle where no one has paddled before. Simply inate with a foot
pump and hit the water in minutes. Please visit our website for more infor-
mation on our products or to nd a dealer near you.
TM
INTRODUCTION
inflatable
inflatable
inflatable
inflatable
inflatable
inflatable
inflatable
inflatable
inflatable
inflatable
inflatable
kayaks
kayaks
kayaks
kayaks
kayaks
kayaks
kayaks
with
with
with
with
with
cutting
cutting
cutting
cutting
cutting
cutting
cutting
cutting
edge
edge
edge
edge
edge
technology
technology
technology
technology
technology
technology
technology
technology
technology
technology
technology

3
TABLE OF CONTENTS
1. Caution/Safety .................................................................. 4
1.1 Boating Safety ........................................................ 5
2. Specification ...................................................................... 6
2.1 Capacity ................................................................. 6
2.2 Features .................................................................. 6
3. Assembly/Inflating/Deflation Instruction .................... 7
3.1 Assembly ............................................................... 7
3.2 Understanding Your Valves................................ 8
3.3 Inflating ................................................................ 10
3.4 Over Inflation ...................................................... 11
3.5 Deflation ............................................................... 11
3.6 Folding ................................................................. 12
4. Guidelines for Usage ..................................................... 12
5. Proper Care and Storage ............................................... 13
6. Repairs ............................................................................. 13
6.1 Repairing Small Punctures and Cuts ............... 13
6.2 Repairing Pinholes ............................................. 14
7. Troubleshooting ............................................................. 15
8. Statement of Origin ....................................................... 17
9. Declaration of Conformity ........................................... 18
10. Warranty and Registration ........................................... 19

TM
4
1. CAUTION - SAFETY WARNING
Users of this product agree by their use to accept the inherent risks involved in this paddlesports
activity and agree to follow all instructions, cautions, and warnings carefully before using this
Kayak.
(PLEASE READ CAUTION STATEMENT CAREFULLY)
SAFETY WARNING
PADDLESPORTS CAN BE VERY DANGEROUS AND PHYSICALLY DEMAND-
ING. THE USER OF THIS PRODUCT SHOULD UNDERSTAND THAT PARTICI-
PATION IN PADDLESPORTS MAY INVOLVE SERIOUS INJURY OR DEATH.
OBSERVE THE FOLLOWING SAFETY STANDARDS WHENEVER USING THIS
PRODUCT.
· GET PADDLESPORTS INSTRUCTIONS SPECIFIC TO THIS TYPE OF CRAFT.
· OBTAIN CERTIFIED FIRST AID TRAINING AND CARRY FIRST AID AND
RESCUE/SAFETY EQUIPMENT.
· ALWAYS WEAR A NATIONALLY APPROVED PERSONAL FLOTATION DEVICE.
· ALWAYS WEAR A HELMET WHERE APPROPRIATE.
· DRESS APPROPRIATELY FOR WEATHER CONDITIONS; COLD WATER AND/OR COLD
WEATHER CAN RESULT IN HYPOTHERMIA. CHECK YOUR EQUIPMENT PRIOR TO
EACH USE FOR SIGNS OF WEAR OR FAILURE.
· NEVER PADDLE ALONE.
· DO NOT PADDLE IN FLOOD CONDITIONS.
· BE AWARE OF APPROPRIATE RIVER WATER LEVELS, TIDAL CHANGES, DANGEROUS
CURRENTS, WEATHER CHANGES, AND STRONG OFF SHORE WINDS.
· SCOUT UNFAMILIAR WATER; PORTAGE WHERE APPROPRIATE.
· DO NOT EXCEED YOUR PADDLING ABILITY; BE HONEST WITH YOURSELF.
· CONSULT YOUR PHYSICIAN PRIOR TO BEGINNING YOUR PADDLESPORTS TRAINING.
· YOU MUST NOT USE ALCOHOL OR MIND ALTERING DRUGS PRIOR TO USING THIS
PRODUCT.
· FOLLOW THE MANUFACTURER’S RECOMMENDATIONS FOR THE USE OF THIS
PRODUCT.
· IF ADDITIONAL OUTFITTING IS REQUIRED, USE MANUFACTURER’S APPROVED
MATERIALS ONLY; DO NOT IMPAIR ENTRY OR EXIT ACCESS.
· READ OWNER’S INFORMATION PACKET PRIOR TO USING THIS PRODUCT.
THE USER OF THIS PRODUCT ACKNOWLEDGES BOTH AN UNDERSTANDING AND AN
ASSUMPTION OF THE RISK INVOLVED IN PADDLESPORTS.
CAUTION
ADVANCED ELEMENTS, INC.
TOLL FREE 866-262-9076
Please read this entire manual for additional safety information. Please pay close aention to items
marked DANGER, WARNING, CAUTION, IMPORTANT, NOTICE, NEVER, and ALWAYS.

AdvancedFrame™ Inatable Kayak Owner’s Manual
5
1.1 Boating Safety
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that follow this symbol to avoid possible injury or
death.
DANGER
Indicates an imminently hazardous
situation which, if not avoided, will
result in death or serious injury or
substantial property damage.
WARNING
Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury or
property damage.
CAUTION
Indicates a potentially hazardous
situation which, if not avoided, may
result in property damage.
CAUTION
Used without the safety alert symbol
indicates a potentially hazardous
situation, which, if not avoided, may
result in property damage.
NOTICE
Indicates installation, operation or
maintenance information which is
important but not hazard-related.
The precautions listed in this manual and on the cra are not all-inclusive. If a procedure,
method, tool or part is not specically recommended, you must satisfy yourself that it is safe
for you and others, and that the cra will not be damaged or made unsafe as a result of your
decision. REMEMBER - always use common sense when paddling YOUR KAYAK!

TM
6
2. SPECIFICATION
Dimensions:
Length: 10’5”
Width: 34”
Weight: 36 lbs (16 kg)
Max. Person Capacity: 235 lbs (107 kg)
Max. Persons & Gear Capacity: 300 lbs (136 kg)
Recommended Pressure:
Main chambers: 2.0 psi (0.14 bar)
Floor chamber: 1.0 psi (0.07 bar)
2.1 Capacity
The person/load capacity is determined by the availability of proper seating on the kayak.
Acceptable seating determines the number of passengers, not the overall load capacity.
MAXIMUM CAPACITIES
300 LBS PERSON, GEAR
PRESSURE = 2.0 psi (main chambers)
MANUFACTURER: ADVANCED ELEMENTS, INC. CONCORD, CA USA 94524
MODEL AE1012 - ADVANCEDFRAME™ KAYAK
COMPLIANCE
WITH
ISO 6185-1
TYPE III, A
0123
1+ = 136 kg
0,14 bar (main chambers)
1PERSON OR 235 LBS.
THIS BOAT COMPLIES WITH NMMA STANDARDS OF EFFECT
ON THE DATE OF CERTIFICATION
NATIONAL MARINE MANUFACTURES ASSN.
NOT INTENDED FOR MECHANICAL PROPULSION
2010
AdvancedFrame™ Kayak Capacity Label
WARNING: Do not exceed the certied maximum capacities under any circumstances.
Overloading will reduce freeboard and increase the likelihood of swamping, especially in heavy
seas. Overloading causes handling to become sluggish, making it dicult to react quickly.
2.2 Features
Hull Design: Built-in Aluminum ribs dene the bow and stern and improve tracking.
Durable: 3 Layers of material for extreme puncture resistance.
Easy to Set Up: Pre-assembled at the factory. Simply unfold, inate and aach the seat.
Comfortable: High support, adjustable padded seat provides comfort for hours of paddling.
Style: Looks and paddles similar to a rigid hard-shell kayak with the portability of an inatable.

AdvancedFrame™ Inatable Kayak Owner’s Manual
7
3. ASSEMBLY/INFLATING/DEFLATION INSTRUCTION
The AdvancedFrame™ Kayak has a rigid frame in the bow and stern that enhances its performance.
3.1 Assembly
The illustration below shows the general assembly of the kayak. Your kayak comes from the
factory pre-assembled. The only assembly you should need to do is aach the adjustable seat.
INFLATABLE FLOOR
ADVANCEDFRAME
OUTER COVER
BOW RIB STERN RIB
Step 1
Step 2
Step 3
Step 1
1. Your AdvancedFrame™ kayak comes from the factory pre-assembled however should you
take it apart you will need to insert the aluminum Bow rib and the Stern Rib into the webbing
slots on the cover of the AdvancedFrame™ tube (while deated).
2. Place the AdvancedFrame™ (with Ribs installed), into the Outer Skin, making sure that the
air valve is upright and at the back of the boat, and lined up with the opening on the outer
cover. Chamber 1 and 2 are separate chambers but equalize in pressure because they are

TM
8
inside a fabric cover. Ideally you want to put half of the air in chamber 1 and half in chamber
2. This way if you suddenly lose pressure in one chamber you should have another chamber
as a safety.
3. With the AdvancedFrame™ tube installed inside the outer skin place the inatable oor
inside the center of the AdvancedFrame™ with twist valve up.
4. Aach the adjustable backrest to the AdvancedFrame™ side tubes by fastening buckles.
3.2 Understanding Your Valves
Advanced Elements AdvancedFrame™ kayak uses the following valves. The Advanced
Elements spring valve has the function and durability of other military type valves and is
compatible with most standard pumps. The lock nut holds the valve in place with the cover for
easy ination. The following gures will have details on how to operate the valves.
To Inate: The valve’s plunger stem should be in the up/outward position ush with the valve
threading.
To Deate: The valve’s plunger stem should be set in the down/inward position recessed in the
valve threading.
In order to switch the valve from inate to deate or vice-versa, simply use your nger to
press the valve stem down/inward and rotate it a 1/4 turn to either lock it down for deate, or
unlock it (stem will spring up) for inate.
How the Spring Valve Works:
When the valve is in the inate (up/outward) position, the air being pumped in pushes the
spring-loaded plunger open, allowing air to enter the air chamber, but not leing it escape.
When the valve is in the deate (down/inward) position, the spring loaded plunger is wide open
allowing the air to come rushing out of the air chamber. If the valve is in the inate position, the
valve’s plunger stem will be ush with the rim of the valve. If the valve is in the deate position,
the valve’s plunger stem will be inside, or lower than, the rim of the valve. To change the valve
from the inate position to the deate position, simply use your nger to press the valve plunger
stem down/inward, and give it a 1/4 turn. This will lock the plunger open and allow the air to
rush out. Use the same procedure in reverse to unlock the valve plunger, allowing it to spring up
into the inate position.
Special Note: If you are using a 12v inator, like those that come with most inatable maresses
or those that plug into car cigaree lighters, you may need to have the valve in the deate (down/
inward) position because these types of pumps typically do not provide enough air pressure
to press the plunger open to allow air into the air chamber. Additionally, 12v inators do not
provide enough pressure to fully inate the kayak, so you will need a secondary pump to nish
the job.

AdvancedFrame™ Inatable Kayak Owner’s Manual
9
Using the NEW “Screw-on” Spring Valve Adaptor:
The screw-on Spring Valve Adaptor was designed to enable the pump hose to securely connect to
the Advanced Elements Spring Valve without falling o during ination, making ination easier.
The valve adaptor also has a semi-circle protrusion that depresses the valve stem, opening the
valve slightly to allow pumps with pressure gauges to take a constant reading. When inating
the kayak using the Spring Valve Adaptor, the valve should be in the inate position.
Special Note: The Spring Valve Adaptor comes with all current Advanced Elements pumps,
with the exception of the 12v inator, and will aach to any Advanced Elements pump that
does not have the adaptor already included, with the exception of the 12v inator. The Spring
Valve Adaptor will also aach to some other manufacturer’s pumps, but you must check the
aachment style at the end of the pump hose to be sure it will t.
Figure 1. Inate/Deate Spring Valve
OPERATINGTHE“TWIST”VA LVES
TWIST TO OPEN / INFLATE / THEN CLOSE
TWIST VALVE
PUMP HOSE
INSERT
1
2
Figure 2. Inate/Deate Twist Valve
To begin inating your kayak, you will need a Bellows Foot Pump or a Double Action Hand
Pump. Never use compressors, CO2 or compressed air as they may damage your kayak.

TM
10
Diagram of Ination Chambers
3.3 Inating
IMPORTANT: Before inating, check to be sure that the kayak is completely assembled.
Inate your kayak in the following order. Failure to follow these instructions may cause
damage to your kayak. Do not over inate.
1. Partially inate chamber 1 until the kayak begins to ll out or appears to be half way inated
then close cap. Check to be sure the valve is in the inate position (See Figure 1).
2. Inate chamber 2 until the AdvancedFrame™ tube is rm to touch (2 psi ONLY).
3. Inate chamber 3 “oor“ (using appropriate ing) twist valve open to inate and twist
closed when complete. Fill until rm. Do Not Over-Inate! (1.0 psi ONLY)
4. Inate Coaming chambers 4 & 5 until rm. Never over-inate! (1.0 psi ONLY)
5. Inate chamber 6 & 7 for desired deck li. Never over-inate! (1.0 psi ONLY)
6. Make sure all valves are closed tightly and properly.
7. Finally, Insert Plastic Bow and Stern forms into pocket on bow and stern (Figure 3).
CAUTION: Water temperature and weather will aect the air pressure of the kayak. In cold
weather your boat will lose some pressure as the air inside contracts. If this occurs, you may want
to add a bit more air to improve your kayak’s performance. However in hot weather, or prolonged
direct sunlight, the air inside will expand. You must let some air out of the appropriate chambers
to prevent the kayak from failing due to overpressure. You should avoid exposing your kayak to
extreme temperatures (hot or cold).

AdvancedFrame™ Inatable Kayak Owner’s Manual
11
Figure 3. Plastic Bow and Stern Insert
INFLATION TIPS
Use either a bellows style foot pump or two-way hand pump to inate your kayak. Be sure that
the ing on the pump hose ts snug in the valve on the kayak. NEVER USE COMPRESSORS,
CO2, OR COMPRESSED AIR AS THEY MAY DAMAGE YOUR KAYAK. The main chambers use
high-end military style, plunger valves (Push in and twist to activate the spring-loaded check
valve for inflating, or push-in and twist to lock open for deflating).
3.4 Over Ination
CAUTION: Water temperature and weather will aect the air pressure of the kayak. In cold
weather and water your kayak will lose some pressure. If this occurs, you may want to add a
bit more air to the kayak to improve performance. In hot weather or prolonged sunlight, the air
inside the kayak will expand. You must let some air out of the appropriate chambers to prevent
the kayak from failing due to overpressure. You should avoid exposing your kayak to extreme
temperatures (hot or cold).
3.5 Deation
1. Remove the caps from chamber 1 & 2.
2. Push stems inward and rotate to deate position (See Figure 1).
3. Open twist valves on chambers 3 through 7.
4. Once the chamber is deated you can use your pump to vacuum out any additional air for
improved folding. This requires a pump capable of deating.

TM
12
3.6 Folding
NOTICE: Reverse your pump to completely deate all chambers.
1. Completely deate all air chambers and thoroughly dry kayak and remove the seat
reversing your pump to pump out all the remaining air will make folding easier.
2. Remove plastic Bow and Stern forms and seat then lay kayak out at.
3. Fold in half, down the center
(right to le)(A).
4. Fold into 4 equal sections.
5. Place into duel bag.
FOLD
FOLD
FOLD
FOLD
12
34
4. GUIDELINES FOR USAGE
Paddlesports can be very dangerous and physically demanding. The user of this product should
understand that participation in paddlesports may involve serious injury or death. Observe the
following safety standards whenever using this product. The user of this product acknowledges
both an understanding and an assumption of the risk involved in paddlesports.
Aer you have inated your kayak and before you put it in the water, inspect your equipment
for obvious signs of wear or failure. Review local rules and regulations and read again the
“CAUTION” statement.
Most areas have local laws and regulations about the use and equipment of small boats. Usually
a phone call to the local authorities will provide you with the needed information. Some areas
may require that you register and display a registration number on the front of your kayak.
Once you have been issued a number, it is best to ax it to the kayak by printing it on the
material with a permanent ink marker. If you are required to display a sticker or vinyl leers, an
inatable boat ID kit can be purchased at most marine stores.
Your kayak is designed to be paddled with a double bladed kayak paddle. Paddle with short
and even strokes. Keep the blade close to the kayak and the paddle almost vertical. Pull with
your lower hand and push with your upper hand. To reduce the amount of swaying at the
front of the kayak, ease o on the force of your stroke. Paddling with a backward stroke can
sometimes oer quick maneuverability.

AdvancedFrame™ Inatable Kayak Owner’s Manual
13
ALWAYS practice safety and take the time to learn about the area where you are paddling. Get
ocial information about the local tides and currents before paddling there. Be careful that
you do not over estimate your strength, your endurance or your skill. Be careful never to under
estimate weather conditions. Be aware of the dangers before you begin. Be aware of your skill
level. Be sure you understand and accept the risk of these dangers. There are many paddling
clubs all over the world. These can be a great source of information on places to paddle, people
to paddle with and most importantly, continued safety practices.
5. PROPER CARE AND STORAGE
Your inatable kayak is made of very durable materials. However, like anything else, proper
use and care will increase the life of your kayak. Before storing your kayak, make sure it is both
CLEAN and DRY. You may clean your kayak with a mild soap and water. NEVER use strong
solvents to clean your kayak as they will destroy the material.
NEVER unzip the chamber cover when the kayak is inated.
Be sure to rinse your kayak with fresh water aer every use in salt water and allow it to dry
thoroughly before storing. Use a dry towel to wipe up all moisture. It should be deated and
kept out of direct sunlight when stored. Avoid exposure to extreme temperatures (hot or cold).
If your boat is exposed to freezing temperatures while storing, allow it to warm up before
unfolding.
Do not store your kayak for an extended period of time while wet.
Follow these steps for removing excess water.
1. Unzip the 2 zippers that run down the center of the kayak.
2. Remove the gray fabric tube and cover, along with the inatable oor, separating it
from the outer cover. In order to completely separate these parts, it is necessary to
unscrew the locking nut on the spring valve.
3. Use a sponge or towel and wipe up any excess water in the outer cover.
4. Wipe o the oor (top and boom)
5. If there is sand or gravel in the kayak, you can hose out the cover, and then wipe it
down with a towel.
6. Most of the time you can just pull out the inatable oor and wipe out the inside of the
kayak absorbing most of the water, then pack it up.
6. REPAIRS
All kayaks come with a repair kit that includes glue and several patches. This should remain
with the kayak in the event that you may need it. If service is required for your kayak, please call
866-262-9076 for assistance.
6.1 Repairing Small Punctures and Cuts
1. Cut a rounded patch at least ¼” or ½” larger than the hole or cut.
2. Clean the area where the patch will be placed with water and/or mild soap.
3. Make sure all surfaces are dry.
4. In a well ventilated area, spread a thin layer of glue on both the patch and on the
damaged area. Let it sit for three to ve minutes or until tacky.

TM
14
6.2 Repairing Pinholes
1. Inate the PVC tube. Locate the pinhole by sponging soapy water over the tube until
you see air bubbles. Mark the location of the pinhole.
2. Deate the tube and dry the aected area. Apply a drop of glue to the pinhole
3. Allow glue to dry completely.
4. Do not inate the kayak for at least twelve hours.
PROBLEM
Does not hold air
while inating.
The kayak is sagging
or under inated.
The kayak will not hold
full pressure for more
than a couple of hours.
Kayak still loses air.
Tube is kinked or
bent in.
The n is bent.
The oor has formed
a large bubble.
SOLUTION
The spring valve uses a plunger system. The only time the plunger
should be in the open position is when you are deating. Make sure
that the plunger is closed to inate. Push the plunger in and rotate
counter-clockwise.
Be sure that the right pump is being used. You need a bellows foot
pump or a double action hand pump. A 12-V electric does not supply
enough pressure to fully inate the kayak. The 12-V can be used to par-
tially inate the kayak but one of the other pumps is needed to top it o.
Make sure that the plunger is in the closed position. It should only
be open when deating. If it is open, the only seal is the black rubber
gasket inside the cap. Even then, a lile air may still leak out.
If you have checked all the previous possible reasons for the kayak
losing air, then there may be a pinhole or a puncture somewhere on the
tube. Pull tube from outer covers. Inate. If you cannot see or hear
where a leak may be, take a clean rag with soapy water and begin rub-
bing the tube. If a hole is present, bubbles will continually form. Repair
using repair kit. If it is a very small pinhole, a dab of the glue may be
sucient.
The tube just needs to be adjusted. When kayak is fully deated try ad-
justing the position of the tube inside of the outer shell. Then reinate.
Aer inating the kayak, turn upside down and leave out in sun for ap-
proximately ten minutes. Fin will conform to its original shape. Even if
it is slightly bent, it will not aect the kayaks performance.
If two of the ridges in the oor have formed one large one, the I-beam
has come apart. This is caused by over ination. It cannot be repaired.
It is important to take all over ination warnings very seriously.
7. TROUBLESHOOTING

AdvancedFrame™ Inatable Kayak Owner’s Manual
15
PROBLEM
Water in the kayak.
The kayak dris to
one side.
SOLUTION
There will almost always be a lile water in the kayak. One reason is the
water drips o of the paddle and into the kayak. Another is some will
puddle up on the deck and leak through the zipper. Make sure that the
deck lis are fully inated so a puddle does not form. You can also get
a spray skirt from our accessories list from a dealer. This will help keep
the inside of the kayak dry as well as you.
A kayak will always head in the direction of your last stroke. The longer
the kayak the less this is usually noticed. If it is driing in the opposite
direction, the oor may not be aligned. Make sure that the oor is prop-
erly centered inside the kayak cover. If the oor is o-center it will cause
uneveness in the kayak.

16
PADDLING NOTES:
It is alway a good idea to keep nots of your paddling experiences. Your notes can serve as a reminder
of what to look out for, as well as what gear to bring along, and what conditions are like.
DATE TIME LOCATION NOTES

Note: If your state requires the licensing of this boat, please use the form below. If you need any assistance filling
out this form, please contact Advanced Elements Customer Service Department.
MANUFACTURER’S STATEMENT OF ORIGIN
FOR A VESSEL SOLD IN THE STATE OF_____________________________________
The undersigned manufacturer hereby certies that the new boat described below, the property of
said manufacturer, has been transferred this _________day of _____________________, 20_________on
Invoice# _________________to:
Owner’s/Dealer’s Name_____________________________________________________________
Address___________________________________________________________________________
City, State, Zip______________________________________________________________________
Model Name Model Year Manufacturer’s Hull Identication#
m AdvancedFrame™ Kayak (AE1012) __________ HIN# ___________________________
Type: Kayak Hull Material: PVC/Polyester
Length Overall: 10’5” Beam: 34”
U. S. Coast Guard Capacity Plate Information (where applicable):
Maximum persons capacity in whole persons: 235 lbs (107 kg)
Maximum weight capacity (persons & gear): 300 lbs (136 kg)
The manufacturer further certies that this was the rst transfer of such new boat and that all
information given herein is true and accurate to the best of their knowledge
TM
P.O. Box 5128 Concord, CA 94524
Signature_________________________________________________________________________________
FIRST ASSIGNMENT
FOR VALUE RECEIVED, in the amount of $ __________________________________________________,
the undersigned hereby transfers the Certicate of Origin and the boat described therein
to _______________________________________________________________________________________
Address __________________________________________________________________________________
and certies that the boat is new and has not been registered in this or any other state; Advanced
Elements, Inc. also warrants the title of said boat at time of delivery, subject only to the liens and
encumbrances as set out below:
Amount of Lien Date To whom Due Address
___________________ __________ __________________ ___________________________________
Dates___________________________ 20 _________, at _____________________ ____________________
___________________________ By:___________________________________________________________
Transferrer (Firm name) Sign Here ___________________________________________________________
Before me personally appeared _____________________________ who by me being duty sworn under
oath says the statements set forth above are true and correct. Subscribed and sworn to me before
this __________ day of _____________________________ 20 ___________.
___________________________________Notary Public Date commission expires_______________
(SEAL)

Declaration of Conformity
(according to ISO/IEC Guide 22 and EN 45014)
   Manufacturer’s Name: Advanced Elements, Inc.
   Manufacturer’s Address: P.O. Box 5128
Concord, CA 94524
 declares, that the product:
   Product Name: AdvancedFrame™ Kayak
   Model Number (s): AE1012
to which this declaration relates, meets the essential health and safety
 requirements and is in conformity with the relevant EU Directives listed below:
General Product Safety Directive
using the relevant section of the following EU standards and other normative
documents:
EN / USI 6185-1 : 2006
ABYC H28-76
Date: January 1, 2011
Clay Haller, President
This product complies with European directives for recreational vessels as
published by the International Organization for Standardization (ISO).

IMPORTANT!
PLEASE READ THIS MANUAL CAREFULLY BEFORE PROCEEDING.
AFTER READING THIS MANUAL, SAVE THESE INSTRUCTIONS
FOR FUTURE REFERENCE.
If you would like a catalog of our latest products please
visit our website at
www.advancedelements.com
or call Toll Free 866-262-9076
PLEASE COMPLETE THE OTHER SIDE OF THIS
WARRANTY REGISTRATION CARD AND RETURN TO ADVANCED ELEMENTS, INC.
TM
P.O. Box 5128
Concord, CA 94524
1-866-262-9076
www.advancedelements.com
Email: [e-mail]
PLACE
STAMP
HERE