Advantech IPC-610-H User manual

IPC-610-H
4U Rackmount Chassis
User’s Manual

Copyright
Advantech Co., Ltd copyrights this documentation and the software
included with this product in 2002. All rights are reserved. Advantech
Co., Ltd. reserves the right to make improvements in the products
described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated or
transmitted in any form or by any means without the prior written
permission of Advantech Co., Ltd. Information provided in this manual
is intended to be accurate and reliable. However, Advantech Co., Ltd.
assumes no responsibility for its use, or for any infringements of the
rights of third parties, which may result from its use.
Acknowledgments
PC-LabCard is a trademark of Advantech Co., Ltd. IBM and PC are
trademarks of International Business Machines Corporation. MS-DOS,
Windows, Microsoft Visual C++ and Visual BASIC are trademarks of
Microsoft Corporation. Intel and Pentium are trademarks of Intel
Corporation. Delphi and C++ Builder are trademarks of Inprise
Corporation.
CE notification
The IPC-610-H, developed by ADVANTECH CO., LTD., has passed the
CE test for environmental specifications when shielded cables are used
for external wiring. We recommend the use of shielded cables. This kind
of cable is available from Advantech. Please contact your local supplier
for ordering information.
IPC-610-H User’s Manual
ii

On-line Technical Support
For technical support and service, please visit our support website at:
http://www.advantech.com/support
Note:
DDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDD
DDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDD
DDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDD
DDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDD
Part No. 2003178400 1st Edition
Printed in Taiwan July 2002
iii

Contents
CHAPTER 1 GENERAL INFORMATION...................................... 2
1.1 INTRODUCTION................................................................ 2
1.2 SPECIFICATIONS .............................................................. 2
1.3 PASSIVE BACKPLANE OPTIONS ....................................... 3
1.4 POWER SUPPLY OPTIONS................................................. 4
Tablel 1-1 Installation Flow Chart ..................... 4
1.5 SYSTEM REGULATION ..................................................... 5
Tablel 1-2 Installation Flow Chart ..................... 5
1.6 DIMENSIONS.................................................................... 5
Fig. 1-1 Installation Flow Chart ......................... 5
1.7 EXPLODED DIAGRAM ...................................................... 6
Fig. 1-2 Installation Flow Chart ......................... 6
CHAPTER 2 SYSTEM SETUP.......................................................... 8
2.1 SYSTEM INSTALL............................................................. 8
2.1.1 Attaching the handles.......................................... 8
2.1.2 Removing the top cover ...................................... 8
Figure 2-1........................................................... 8
2.1.3 Chassis Front and Rear Sections ......................... 9
Figure 2-2........................................................... 9
Figure 2-3......................................................... 10
2.1.4 Drive Bay Installation ....................................... 10
Figure 2-4......................................................... 11
2.2 IPC-610-H SERIES INSTALLATION ................................ 12
2.2.1 IPC-610BP-00XH ................................................ 12
2.2.2 IPC-610MB-00XH............................................... 12
2.3 LED INDICATORS.......................................................... 13
2.3.1 System Status LED .............................................. 13
Tablel 2-1 ......................................................... 13
2.3.2 Power Status LED................................................ 13
Table 2-2 .......................................................... 13
2.4 COOLING FAN AND FILTER ............................................ 14
Figure 2-5......................................................... 14
Figure 2-6......................................................... 14
Figure 2-7......................................................... 15
IPC-610-H User’s Manual
iv

2.5 INSTALLING CPU CARDS & ADD-ON CARDS ............... 15
APPENDIX A BACKPLANE........................................................... 18
Figure 1.1 ......................................................... 18
Table 1.1 Connectors........................................ 19
Table 1.2 Routing Table ................................... 20
v

General Information
1
CHAPTER

Chapter 1 General Information
1.1 Introduction
IPC-610-H is a 4U height 14-slot rackmount IPC chassis designed for
building mission-critical applications. The unit includes a versatile
14-slot passive-backplane by option (which supports ATX M/B form
factor), a high-efficiency 300W ATX with power factor correction (PFC)
power supply, and dual easy maintenance cooling fan which provides
abundant cooling. A wide range of standard computing peripherals can
be integrated with the chassis to meet different application development
under mission-critical environment 24 hours a day, 7days a week.
1.2 Specifications
General
! Construction: Heavy duty steel chassis
! Drive bay: Shock-proof. Front accessed three 5.25" & one 3.5”
drivers
! Cooling system: Dual easy-to-replace 84 ~ 114 CFM cooling
fan with front-access air filter
! Controls: Power switch (on-off or momentary) and reset switch
behind the lockable door
Indicators
! Power: Green LED shows the power status
! HDD: Green LED for HDD activity
! Voltages: 3.3V/+5V/+12V/-5V/-12V/Vsb single-color LED
(green) shows the voltage status
! Connectors: Front access USB and PS/2 keyboard, rear panel
9-pin connector (9-pin connector is not included for the M/B
version)
! Paint Color: Pantone 414U Gray, textured
! Operating temperature: 0 ~ +40°C (32°F ~ 104°F)
IPC-610-H User's Manual
2

! Storage temperature: -40° to +60°C (-40° to +140°F)
! Relative Humidity: 10 ~ 95%@40°C, non-condensing
! Vibration: (Operating) 5Hz ~ 500Hz, 0.5G rams
! Shock (operating): 2.0 G with 11m Sec duration, 1/2 sine wave
! Acoustic Noise: Less than 52 dB sound pressure at +5° to
+28°C (+41° to +82°F)
! Altitude: 0 to 3048m (0 to 10,000 ft)
! Slide rails: General Device C-300 series supported
! Dimensions: 482(W) x 173(H) x 480(D)mm (19”x 6.8” x 18.9”)
! Weight: 16-18kg (35.2 – 39.6lb)
! Safety: CCC approved
1.3 Passive Backplane Options
Single System Backplane models (refer appendix for details)
# PCA-6114P4-C
3

1.4 Power Supply Options
Specifications
Model Name Watt Input Output Mini-load Safety MTBF
PS-300ATX-Z
(ATX,PFC) 300 W
AC 90~135V
AC 180~265V
(Full-range)
+5 V @ 30 A
+3.3 V @ 24 A
+12 V @ 15 A
-12 V @ 0.8 A
-5 V @ 0.3 A
+5 Vsb @ 2 A
+5V @ 1A
+12V @ 0.5A
UL/cUL/CSA,
CE EN61000-3-2
Class D
TUV, Nordic,
CB
CCC
100,000 hours @ 25℃
275W load
PS-400ATX-Z
(ATX PFC) 400 W AC 90~264V
(Full-range)
+5V @ 42A
+3.3V @ 20A
+12V @ 14A
-12V @ 1A
-5V @ 1A
+5 Vsb @ 0.75 A
+5V @ 2.5A
+12V @ 0.5A
UL/cUL/TUV/
CCC
100,000 hours @ 25℃
75% load
PS-250ATX-Z
(ATX,PFC) 250 W AC 95~132V
AC 190~264V
+5V @ 27A
+3.3V @ 20A
+12V @ 13A
-12V @ 0.8A
-5V @ 0.3A
+5 Vsb @ 2 A
+5V @ 0.5A
+12V @ 0.3A
UL/cUL/CSA/TUV/C
B/CCC 100,000 hours@25℃
+3.3V @ 0.3A
+3.3V @ 0.2A
Tablel 1-1 Installation Flow Chart
IPC-610-H User's Manual
4

1.5 System Regulation
Model Name With Power Supply With Backplane or
MotherBoard Regulation
IPC-610P4-25ZH PS-250ATX-Z(ATX PFC) PCA-6114P4-C CCC
IPC-610BP-00XH w/o w/o None
IPC-610BP-25ZH PS-250ATX-Z(ATX,PFC) w/o CCC
IPC-610BP-30ZH PS-300ATX-Z(ATX PFC) w/o CCC
IPC-610MB-00XH w/o w/o None
IPC-610MB-25ZH PS-250ATX-Z(ATX,PFC) w/o None
IPC-610MB-30ZH PS-300ATX-Z(ATX PFC) w/o None
Tablel 1-2 Installation Flow Chart
1.6 Dimensions
Fig. 1-1 Installation Flow Chart
5

1.7 ExplodedDiagram
Fig.1-2InstallationFlowChart
IPC-610-H User's Manual
6

System Setup
2
CHAPTER

Chapter 2 System Setup
2.1 System Install
WARNING: Before starting the installation process, make sure to
disconnect all power from the chassis. Do this by turning off the power
switch, and unplugging the power cord from the power outlet. When in
doubt, consult with an experienced technician.
2.1.1 Attaching the handles
The handles for the front panel are in the accessory box. To install the
handles, simply secure them to the front panel with the screws provided.
2.1.2 Removing the top cover
First, remove the chassis cover. You don’t need any screwdriver.
Top cover is fixed to the chassis by two thumbscrews
To remove the top covers:
1. Release two thumbscrews on rear upper location the chassis.
2. Pull back and lift off the cover.
Figure 2-1
IPC-610-H User's Manual
8

2.1.3 Chassis Front and Rear Sections
The front panel switches which behind the door are used for system
power switch and system reset. The door cover is on the right side of
door cover, there are system LED status and key lock switch. The
USB and P/S 2 keyboard connector are on the left side of front panel.
Figure 2-2
Power On/Off
Switch
System Reset
Figure 2-3
System Reset : Press this switch to reinitialize the system. This is the
same as the hardware reset button.
Power On/Off Switch: Use this switch to turn on/off the system power.
9

Momentary Switch: Use this switch and by way of ATX (PS_ON)
function to turn on system power. Please use system shutdown to turn off
system power automatic or press momentary switch for a while to turn
off system power
USB connector: If you have any USB interface device want to connect
with system, you could use this connector.
PS/2 connector: If you want to connect PS/2 keyboard, you could use
this connector.
The rear section of B/P version includes B/P rear window. The rear
14-slot I/O brackets and the sheet metal kit for section of M/B version
includes M/B rear window, 7-slot I/O brackets, ATX M/B I/O cover.
Figure 2-3
2.1.4 Drive Bay Installation
The Standard Drive Bay of the IPC-610-H can hold 5.25” x 3 and 3.5” x
1 devices
IPC-610-H User's Manual
10

Installation disk drives
1. Remove the top cover
2. Undo the four screws of cushion and four screws fixing the
Standard Drive Bay on right side
3. Lift off the Standard Drive Bay. See Figure 2-4
4. Insert the drives into their proper locations in the drive bay and
secure them with the screws provided.
5. Connect the disk drive power and signal cables.
Figure 2-4
11

2.2 IPC-610-H Series Installation
The IPC-610-H can be of two basic models, IPC-610BP-00XH and
IPC-610MB-00XH.
2.2.1 IPC-610BP-00XH
IPC-610BP-00XH has no backplane, no power supply and has
momentary switch on front panel. The momentary switch is suitable for
ATX power supply such as PS-250ATX-Z, PS-300ATX-Z.
For IPC-610BP-00XH, please plug 20-pin ATX power connector with
backplane first, then use a orange-white wire (1700030500) to connector
between CN# (PSON_GND_5VSB) of Backplane and “ATX feature
connector” (CN20) of SBC, finally connect POWER SW wire with the
“ATX soft power switch”(CN21) on SBC to finish the installation.
2.2.2 IPC-610MB-00XH
ACP-610MB-00X is for M/B using, it is with ATX M/B rear I/O.
ACP-610MB-00X is without M/B inside, has no power supply and has
momentary switch on front panel. The momentary switch is suitable for
ATX power supply such as PS-250ATX-Z, PS-300ATX-Z. For
ACP-610MB-00X, please plug 20-pin ATX power connector with your
ATX M/B, and then connect POWER SW wire with your ATX M/B to
finish the installation. Please refer your ATX M/B installation guide for
correct connection.
IPC-610-H User's Manual
12

2.3 LED Indicators
2.3.1 System Status LED
The System Status LED shows as following:
LED Description GREEN
PWR System Power Normal
HDD Hard Drive
activity
Data access
Tablel 2-1
2.3.2 Power Status LED
The Power Status LED indicates the status of the backplane voltage
signals.
LED Description Light No light
+3.3V +3.3V signal Normal No output
+5V + 5V signal Normal No output
+12V +12V signal Normal No output
-5V - 5V signal Normal No output
-12V -12V signal Normal No output
+5Vsb +5Vsb signal Normal No output
Table 2-2
When an LED fails to light, it indicates a problem with one of the
voltage signals. Check to make sure that the power supply connector is
properly attached to the backplane. If problem persists, consult an
experienced technician.
13

2.4 Cooling Fan and Filter
There are two (2) Cooling Fans located inside the chassis. The Cooling
Fans are easy maintenance and provide adequate cooling to the system
by blowing air inward. Please refer the Figure 2-5 and Figure 2-6 to
replace the defective fan. Press the location A and then pull the B
which is showed on Figure 2-6 then the connector could be released.
Please refer Figure 2-7 to change the filter if you found the filter was
blocked with dust or other particles
Figure 2-5
A
B
Figure 2-6
IPC-610-H User's Manual
14